Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type)
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047060 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type)  Back Sonar Sensor RH Circuit  


DESCRIPTION

The ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance between the vehicle and the obstacle, and sends the distance value as a signal to the clearance warning ECU assembly.

WIRING DIAGRAM

E270572E06
4.156,2.094 5.719,2.448 1.563,0.354 10 No. 3 Ultrasonic Sensor (Rear Center Sensor LH) 4.156,1.906 4.469,2.104 0.313,0.198 10 S3 4.229,0.552 4.385,0.75 0.156,0.198 10 4 4.219,0.938 4.375,1.135 0.156,0.198 10 2 4.219,1.313 4.375,1.51 0.156,0.198 10 6 4.417,0.667 4.729,0.865 0.313,0.198 10 SO 4.396,1.042 4.708,1.24 0.313,0.198 10 BO 4.427,1.396 4.74,1.594 0.313,0.198 10 EO 2.833,0.958 2.99,1.156 0.156,0.198 10 1 2.833,0.563 2.99,0.76 0.156,0.198 10 3 2.833,1.313 2.99,1.51 0.156,0.198 10 5 2.531,0.677 2.844,0.875 0.313,0.198 10 SI 2.531,1.052 2.844,1.25 0.313,0.198 10 BI 2.542,1.406 2.854,1.604 0.313,0.198 10 EI 1.604,1.875 1.917,2.073 0.313,0.198 10 S2 1.594,2.073 3.146,2.438 1.552,0.365 10 No. 3 Ultrasonic Sensor (Rear Center Sensor RH)

PROCEDURE

1.INSPECT NO. 3 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
a.
E270573E02
1.958,0.896 2.375,0.479 false 1.958,1.115 2.656,1.115 false 1.958,1.365 2.417,1.74 false 0.948,0.563 1.5,0.896 false 0.792,1.115 1.469,1.115 false 1.021,1.75 1.479,1.354 false 2.729,1.031 3.042,1.229 0.313,0.198 10 SI 2.479,0.375 2.792,0.573 0.313,0.198 10 BI 2.51,1.667 2.823,1.865 0.313,0.198 10 EI 0.521,1.052 0.833,1.25 0.313,0.198 10 SO 0.615,0.458 0.927,0.656 0.313,0.198 10 BO 0.771,1.698 1.083,1.896 0.313,0.198 10 EO

Remove the No. 3 ultrasonic sensor (rear center sensor RH).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BI) - 5 (EI) Always 10 kΩ or higher
1 (BI) - 2 (BO) Always 10 kΩ or higher
3 (SI) - 4 (SO) Always Below 1 Ω
5 (EI) - 6 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CENTER SENSOR LH)

NG

REPLACE NO. 3 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

2.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CENTER SENSOR LH)
a.

Disconnect the S2 No. 3 ultrasonic sensor (rear center sensor RH) connector.


b.

Disconnect the S3 No. 3 ultrasonic sensor (rear center sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S2-3 (SI) - S3-4 (SO) Always Below 1 Ω
S2-1 (BI) - S3-2 (BO) Always Below 1 Ω
S2-5 (EI) - S3-6 (EO) Always Below 1 Ω
S2-3 (SI) - Body ground Always 10 kΩ or higher
S2-1 (BI) - Body ground Always 10 kΩ or higher
S2-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR