Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE(for Single Type) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0050504 SPIRAL CABLE(for Single Type) G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE(for Single Type)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the driver side of RHD and LHD vehicles.

·

The procedures listed below are for the driver side of LHD vehicles.



PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

w/ Vehicle Stability Control System:

Do not remove the steering sensor from the spiral cable sub-assembly.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



a.

Visually check for defects with the spiral cable sub-assembly.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector


OK:

No defects are found.


If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.
B340955C01
0.875,3.073 1.26,3.292 0.385,0.219 1.552,3.021 1.938,3.24 0.385,0.219 1.417,0.188 1.802,0.406 0.385,0.219 2.083,0.188 2.469,0.406 0.385,0.219 0.177,1.531 0.563,1.75 0.385,0.219 2.052,1.99 2.667,1.667 true 2.677,1.563 2.99,1.719 0.313,0.156 10 *1 0.125,0.094 0.438,0.25 0.313,0.156 10 *a 0.958,3.104 1.271,3.302 0.313,0.198 10 G9 1.656,3.052 1.969,3.25 0.313,0.198 10 G8 1.542,0.219 1.854,0.417 0.313,0.198 10 z1 2.208,0.219 2.521,0.417 0.313,0.198 10 z4 0.281,1.552 0.594,1.75 0.313,0.198 10 z2
*1 Interlock
*a Component without harness connected
(Spiral Cable Sub-assembly)


Check the spiral cable sub-assembly.

NOTICE:

When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.


i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 - z4-3 Always 3 Ω or less
G8-2 - z4-4 Always 3 Ω or less
G8-3 - z1-8 Always 3 Ω or less
G8-4 - z1-9 Always 3 Ω or less
G8-5 - z1-10 Always 3 Ω or less
G8-6 - z1-11 Always 3 Ω or less
G8-9 - z1-1 Always 3 Ω or less
G8-10 - z1-2 Always 3 Ω or less
G8-11 - z1-3 Always 3 Ω or less
G8-13 - z1-5 Always 3 Ω or less
G9-1 - z2-2 Always Below 1 Ω
G9-2 - z2-1 Always Below 1 Ω



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 - z4-3 Always 3 Ω or less
G8-2 - z4-4 Always 3 Ω or less
G8-3 - z1-8 Always 3 Ω or less
G8-4 - z1-9 Always 3 Ω or less
G8-5 - z1-10 Always 3 Ω or less
G8-6 - z1-11 Always 3 Ω or less
G8-9 - z1-1 Always 3 Ω or less
G8-10 - z1-2 Always 3 Ω or less
G8-11 - z1-3 Always 3 Ω or less
G8-13 - z1-5 Always 3 Ω or less
G9-1 - z2-2 Always Below 1 Ω
G9-2 - z2-1 Always Below 1 Ω



iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 - z4-3 Always 3 Ω or less
G8-2 - z4-4 Always 3 Ω or less
G8-3 - z1-8 Always 3 Ω or less
G8-4 - z1-9 Always 3 Ω or less
G8-5 - z1-10 Always 3 Ω or less
G8-6 - z1-11 Always 3 Ω or less
G8-9 - z1-1 Always 3 Ω or less
G8-10 - z1-2 Always 3 Ω or less
G8-11 - z1-3 Always 3 Ω or less
G8-13 - z1-5 Always 3 Ω or less
G9-1 - z2-2 Always Below 1 Ω
G9-2 - z2-1 Always Below 1 Ω


If the result is not as specified, replace the spiral cable with sensor sub-assembly.