Home › Drivetrain › EB63 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT
RM3090E _52 Drivetrain _009272 EB63 MANUAL TRANSMISSION / TRANSAXLE _0050734 OUTPUT SHAFT G

EB63 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  INSPECTION  


PROCEDURE

Hide 1.INSPECT 1ST GEAR THRUST CLEARANCE

a.
C194350

Using a dial indicator, measure the 1st gear thrust clearance.

Standard clearance:

0.23 to 0.37 mm (0.00906 to 0.01456 in.)


Maximum clearance:

0.37 mm (0.01456 in.)


If the clearance is more than the maximum, replace the No. 1 transmission clutch hub, 1st gear bush or 1st gear. Replace the part or parts determined to be the most likely cause of the problem.


Hide 2.INSPECT 2ND GEAR THRUST CLEARANCE

a.
C194351

Using a dial indicator, measure the 2nd gear thrust clearance.

Standard clearance:

0.16 to 0.33 mm (0.00630 to 0.01299 in.)


Maximum clearance:

0.33 mm (0.01299 in.)


If the clearance is more than the maximum, replace the inner 2nd gear bearing race, No. 1 transmission clutch hub, 2nd gear or 3rd driven gear. Replace the part or parts determined to be the most likely cause of the problem.


Hide 3.INSPECT 1ST GEAR RADIAL CLEARANCE

a.
C194352

Using a dial indicator, measure the 1st gear radial clearance.

Standard clearance:

0.009 to 0.047 mm (0.00036 to 0.00185 in.)


Maximum clearance:

0.047 mm (0.00185 in.)


If the clearance is more than the maximum, replace the 1st gear, 1st gear needle roller bearing or output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 4.INSPECT 2ND GEAR RADIAL CLEARANCE

a.
C194353

Using a dial indicator, measure the 2nd gear radial clearance.

Standard clearance:

0.009 to 0.047 mm (0.00036 to 0.00185 in.)


Maximum clearance:

0.047 mm (0.00185 in.)


If the clearance is more than the maximum, replace the 2nd gear, 2nd gear needle roller bearing or output shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33321 5.INSPECT OUTPUT SHAFT

a.
C199115

Using a dial indicator and 2 V-blocks, measure the output shaft runout.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the output shaft.


b.
C202200
0.288,3.262 0.413,3.416 0.126,0.154 10 A 2.474,3.239 2.598,3.389 0.124,0.15 10 B 3.012,3.234 3.137,3.384 0.124,0.15 10 C

Using a micrometer, measure the outer diameter of the output shaft journal surface at the locations indicated.

Standard journal diameter:
Journal A:

28.010 to 28.023 mm (1.1028 to 1.1032 in.)

Journal B:

42.180 to 42.200 mm (1.6607 to 1.6614 in.)

Journal C:

36.010 to 36.026 mm (1.4178 to 1.4183 in.)


Minimum journal diameter:
Journal A:

28.010 mm (1.1028 in.)

Journal B:

42.180 mm (1.6607 in.)

Journal C:

36.010 mm (1.4178 in.)


If the outer diameter is less than the minimum, replace the output shaft.


Hide 33335 6.INSPECT 1ST GEAR

a.
C200256

Using a cylinder gauge, measure the inside diameter of the 1st gear.

Standard inside diameter:

57.909 to 57.925 mm (2.2799 to 2.2805 in.)


Maximum inside diameter:

57.925 mm (2.2805 in.)


If the inside diameter is more than the maximum, replace the 1st gear.


Hide 33332 7.INSPECT 2ND GEAR

a.
C200257

Using a cylinder gauge, measure the inside diameter of the 2nd gear.

Standard inside diameter:

57.909 to 57.925 mm (2.2799 to 2.2805 in.)


Maximum inside diameter:

57.925 mm (2.2805 in.)


If the inside diameter is more than the maximum, replace the 2nd gear.


Hide 33345 8.INSPECT 1ST GEAR BUSH

a.
C194374

Using a micrometer, measure the outer diameter of the 1st gear bush.

Standard outer diameter:

51.890 to 51.900 mm (2.0430 to 2.0433 in.)


Minimum outer diameter:

51.890 mm (2.0430 in.)


If the outer diameter is less than the minimum, replace the 1st gear bush.


b.
C194376

Using a cylinder gauge, measure the inside diameter of the 1st gear bush.

Standard inside diameter:

42.200 to 42.215 mm (1.6615 to 1.6620 in.)


Maximum inside diameter:

42.215 mm (1.6620 in.)


If the inside diameter is more than the maximum, replace the 1st gear bush.


Hide 33356A 9.INSPECT INNER 2ND GEAR BEARING RACE

a.
C200309

Using a micrometer, measure the outer diameter of the inner 2nd gear bearing race.

Standard outer diameter:

51.890 to 51.900 mm (2.0430 to 2.0433 in.)


Minimum outer diameter:

51.890 mm (2.0430 in.)


If the outer diameter is less than the minimum, replace the inner 2nd gear bearing race.


b.
C200310

Using a cylinder gauge, measure the inside diameter of the inner 2nd gear bearing race.

Standard inside diameter:

42.200 to 42.215 mm (1.6615 to 1.6620 in.)


Maximum inside diameter:

42.215 mm (1.6620 in.)


If the inside diameter is more than the maximum, replace the inner 2nd gear bearing race.


Hide 33037B 10.INSPECT NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

a.

Coat the 1st gear cone and No. 1 synchronizer ring set (inner ring, middle ring and outer ring) with gear oil.


b.
C195453
0.728,0.541 0.893,0.695 0.165,0.153 10 *1 1.319,0.629 0.934,0.629 false 0.728,1.205 0.893,1.359 0.165,0.153 10 *2 1.378,1.293 0.934,1.293 false 0.728,1.798 0.893,1.951 0.165,0.153 10 *3 1.421,1.886 0.934,1.886 false
*1 Outer Ring
*2 Middle Ring
*3 Inner Ring


Install the inner ring to the 1st gear.


c.

Install the middle ring to the 1st gear.


d.

Install the outer ring to the 1st gear.


e.
C284670
1.406,0.073 1.719,0.271 0.313,0.198 10 false *a
*a Locks in both directions


Check for wear and damage.


f.

Turn the No. 1 synchronizer ring set in both directions while pushing it against the 1st gear cone and check that it locks in both directions.

If the No. 1 synchronizer ring set does not lock, replace the No. 1 synchronizer ring set.


g.
C194379

Using a feeler gauge, measure the clearance between the No. 1 synchronizer ring set and gear spline end.

Standard clearance:

0.88 to 1.72 mm (0.0347 to 0.0677 in.)


Minimum clearance:

0.88 mm (0.0347 in.)


If the clearance is less than the minimum, replace the No. 1 synchronizer ring set.


Hide 33037B 11.INSPECT NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)

a.

Coat the 2nd gear cone and No. 1 synchronizer ring set (inner ring, middle ring and outer ring) with gear oil.


b.
C195454
0.74,0.594 1.208,0.594 false 0.771,1.333 1.24,1.333 false 0.823,2.073 1.292,2.073 false 0.531,0.521 0.844,0.719 0.313,0.198 10 *1 0.573,1.271 0.885,1.469 0.313,0.198 10 *2 0.625,2 0.938,2.198 0.313,0.198 10 *3
*1 Outer Ring
*2 Middle Ring
*3 Inner Ring


Install the inner ring to the 2nd gear.


c.

Install the middle ring to the 2nd gear.


d.

Install the outer ring to the 2nd gear.


e.
C284671
1.625,0.167 1.938,0.365 0.313,0.198 10 false *a
*a Locks in both directions


Check for wear and damage.


f.

Turn the No. 1 synchronizer ring set in both directions while pushing it against the 2nd gear cone and check that it locks in both directions.

If the No. 1 synchronizer ring set does not lock, replace the No. 1 synchronizer ring set.


g.
C194381

Using a feeler gauge, measure the clearance between the No. 1 synchronizer ring set and gear spline end.

Standard clearance:

0.88 to 1.72 mm (0.0347 to 0.0677 in.)


Minimum clearance:

0.88 mm (0.0347 in.)


If the clearance is less than the minimum, replace the No. 1 synchronizer ring set.


Hide 33331 12.INSPECT REVERSE GEAR

a.
C194382
0.146,1.479 0.292,1.688 0.146,0.208 10 B 2.208,3.042 2.354,3.25 0.146,0.208 10 A 0.313,4.271 0.594,4.448 0.281,0.177 10 *a
*a Clearance = A - B


Using a vernier caliper, measure the width of the reverse gear groove (A) and the thickness of the claw part on the No. 1 gear shift fork shaft assembly (B), and calculate the clearance.

Standard clearance (A - B):

0.1 to 0.5 mm (0.00394 to 0.01968 in.)


If the clearance is not as specified, replace the reverse gear and No. 1 gear shift fork shaft assembly.


Hide 33361 13.INSPECT NO. 1 TRANSMISSION CLUTCH HUB

a.
C194383

Check that the No. 1 transmission clutch hub and reverse gear slide smoothly.


b.

Check that the edges of the reverse gear spline gear are not worn down.