Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 2AR-FE)
RM3090E _52 Drivetrain _008754 CLUTCH _0050753 CLUTCH UNIT(for 2AR-FE) A

CLUTCH  CLUTCH UNIT(for 2AR-FE)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

C226308C01
2.063,1.594 2.396,1.302 2.396,1.302 2.625,1.302 false 2.094,3.281 2.427,2.99 2.427,2.99 2.656,2.99 false 1.688,2.885 2.021,2.594 2.021,2.594 2.25,2.594 false 2.729,1.24 3.188,1.438 0.458,0.198 10 SST 2.729,2.917 3.188,3.115 0.458,0.198 10 SST 2.323,2.521 2.781,2.719 0.458,0.198 10 *1
*1 Clutch Disc Assembly


a.

Insert SST into the clutch disc assembly, and then attach them both to the flywheel sub-assembly.

SST
09301-00210  

NOTICE:

Insert the clutch disc assembly in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

C280394C01
1.094,1.24 0.5,1.542 0.5,1.542 1.188,1.271 false 2.167,1.313 2.375,0.958 2.375,0.958 2.708,0.958 true 0.354,1.5 0.51,1.698 0.156,0.198 10 *a 0.792,1.646 0.948,1.844 0.156,0.198 10 3 1.177,1.906 1.333,2.104 0.156,0.198 10 6 1.833,1.833 2.344,2.021 0.51,0.188 10 2, 5 2.552,0.656 2.708,0.854 0.156,0.198 10 8 1.823,0.042 2.406,0.25 0.583,0.208 10 1, 4 0.885,0.542 1.042,0.74 0.156,0.198 10 7 2.802,0.885 3.219,1.073 0.417,0.188 10 SST
*a Matchmark


a.

Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.


b.

Following the order shown in the illustration, tighten the 6 bolts, starting with the bolt located near the knock pin at the top.

SST
09301-00210  

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C204681

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Maximum non-alignment:

0.5 mm (0.0196 in.)



b.
C204682

If the alignment is more than the maximum, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31400 4.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

a.
C197022

Temporarily install the clutch release cylinder to flexible hose tube to a new clutch release with bearing cylinder assembly.


b.

Clean and degrease all installation surfaces for the clutch release with bearing cylinder assembly.


c.
C226305

Install the clutch release with bearing cylinder assembly with 3 new bolts.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

NOTICE:
·

The clutch release with bearing cylinder and installation bolts cannot be reused and must be replaced with new ones.

·

Clean and degrease all installation surfaces and make sure the clutch release with bearing cylinder fits securely with the transaxle during installation. The first bolt should be tightened by hand while holding the clutch release with bearing cylinder.

·

Make sure that none of the clutch spline grease adheres to the clutch release with bearing cylinder.

·

The clutch release with bearing cylinder cannot be disassembled.




d.
C226304

Install the clutch tube boot to the manual transaxle assembly.


e.
C227868

Temporarily install the clutch release cylinder to flexible hose tube to the clutch release bleeder sub-assembly.


f.
C226303

Temporarily install the clutch release bleeder sub-assembly with the 2 bolts.


g.
C280415

Using a union nut wrench, install the clutch release cylinder to flexible hose tube to the clutch release with bearing cylinder assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



h.
C280416C01
2.885,1.625 3.167,1.885 0.281,0.26 10 false .
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 31407B 5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C199329

Using a union nut wrench, disconnect the clutch release cylinder to flexible hose tube from the clutch release bleeder sub-assembly.


b.

Remove the 2 bolts and clutch release bleeder sub-assembly.


Hide 6.INSPECT CLUTCH PIPE LINE

C207383N01
2.573,1.021 2.677,0.823 2.677,0.823 2.865,0.823 false 2.958,0.719 3.354,0.917 0.396,0.198 10 SST

a.

Using SST, apply a pressure of 100 kPa (1.0 kgf/cm2, 15 psi) to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

SST
09992-00242  

If the pressure drops, replace the clutch release cylinder to flexible hose tube.


Hide 31407B 7.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C199329

Temporarily install the clutch release cylinder to flexible hose tube to the clutch release bleeder sub-assembly.


b.

Install the clutch release bleeder sub-assembly with the 2 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


c.

Using a union nut wrench, install the clutch release cylinder to flexible hose tube.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 8.INSTALL CLUTCH TUBE

a.

Temporarily install the bleeder to accumulator tube labeled A and accumulator to flexible hose tube labeled B.


b.
C280409C01
2.229,0.208 1.979,0.208 1.979,0.208 1.729,0.427 true 0.406,1.635 0.563,1.833 0.156,0.198 10 A 2.292,0.135 2.51,0.385 0.219,0.25 10 *a 2.635,2.042 2.792,2.24 0.156,0.198 10 A 2.635,2.469 2.792,2.667 0.156,0.198 10 B
*a Paint Mark


Using a 10 mm union nut wrench, tighten the bleeder to accumulator tube labeled A and accumulator to flexible hose tube labeled B.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



c.

Install the clamp with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

HINT:

Align the clamp and paint mark as shown in the illustration and install the clamp.