Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › 2012.12–2015.10
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0050374 POWER BACK DOOR SYSTEM U

DOOR / HATCH  POWER BACK DOOR SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK DOOR ECU


C278778E02
2.417,0.531 2.833,0.781 0.417,0.25 4.302,0.51 4.719,0.76 0.417,0.25 2.5,0.583 2.958,0.781 0.458,0.198 10 U19 4.375,0.552 4.833,0.75 0.458,0.198 10 U18

a.

Disconnect the U18 and U19 multiplex network door ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U18-1 (ECUB) - Body ground W - Body ground Battery power supply Always 11 to 14 V
U18-7 (IG) - Body ground W - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
U19-8 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
U19-7 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω


c.

Reconnect the U18 and U19 multiplex network door ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U19-10 (DC+) - U19-9 (DC-) B - R Back door lock assembly (back door lock motor) circuit Back door lock motor operating 11 to 14 V
Back door lock motor not operating Below 1 V
U18-20 (MSW) - Body ground W - Body ground Power back door main switch signal Power back door main switch not pushed Below 1 V
Power back door main switch pushed Pulse generation
U18-6 (BDDN) - Body ground LG - Body ground Door control switch signal Door control switch assembly on Below 1 V
Door control switch assembly off Pulse generation
U18-5 (BZR+) - Body ground V - Body ground Wireless door lock buzzer signal Wireless door lock buzzer sounding Pulse generation
Wireless door lock buzzer not sounding Below 1 V
U18-18 (OSL) - U18-17 (OSE) L - GR Power back door sensor assembly LH signal Power back door sensor assembly LH not pressed 4 to 6 V
Power back door sensor assembly LH pressed Below 1 V
U18-16 (OSR) - U18-17 (OSE) SB - GR Power back door sensor assembly RH signal Power back door sensor assembly RH not pressed 4 to 6 V
Power back door sensor assembly RH pressed Below 1 V



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


B264892E77
4.719,0.646 5.167,0.927 0.448,0.281 1.854,0.646 2.302,0.927 0.448,0.281 3.229,0.635 3.677,0.917 0.448,0.281 4.813,0.698 5.271,0.896 0.458,0.198 10 G84 1.938,0.708 2.396,0.906 0.458,0.198 10 G82 3.333,0.698 3.792,0.896 0.458,0.198 10 G83

a.

Disconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G82-2 (+B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
G82-10 (CUTB) - Body ground P - Body ground Battery power supply Always 11 to 14 V
G84-5 (IG) - Body ground LG - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G82-11 (E) - Body ground BR - Body ground Body ground Always Below 1 Ω


c.

Reconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G83-27 (TSW5) - Body ground Y - Body ground Back door opener switch assembly signal Back door opener switch assembly off Pulse generation
Back door opener switch assembly on Below 1 V



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


C278789E03
2.656,5.323 2.958,5.563 0.302,0.24 0.552,5.271 0.854,5.51 0.302,0.24 1.896,6.99 2.198,7.229 0.302,0.24 5.583,5.302 5.885,5.542 0.302,0.24 5.417,7.01 5.719,7.25 0.302,0.24 2.344,1.146 2.656,1.344 0.313,0.198 10 3B 2.708,5.365 3.021,5.563 0.313,0.198 10 3B 3.656,1.052 3.969,1.25 0.313,0.198 10 3C 4.365,1.188 4.677,1.385 0.313,0.198 10 3D 2.26,2.979 2.573,3.177 0.313,0.198 10 3A 0.604,5.302 0.917,5.5 0.313,0.198 10 3A 1.969,7.031 2.281,7.229 0.313,0.198 10 3D 5.646,5.323 5.958,5.521 0.313,0.198 10 3C 3.052,1.063 3.365,1.26 0.313,0.198 10 3E 5.479,7.052 5.792,7.25 0.313,0.198 10 3E

B338301C03
3.521,5.49 3.979,5.74 0.458,0.25 1.51,5.49 1.969,5.74 0.458,0.25 1.438,3.865 1.896,4.115 0.458,0.25 1.219,5.083 1.635,5.083 false 1.052,5 1.365,5.156 0.313,0.156 10 *1 3.615,5.531 3.99,5.698 0.375,0.167 10 G78 1.604,5.521 1.979,5.688 0.375,0.167 10 G79 2.802,1.917 3.177,2.083 0.375,0.167 10 A 1.615,3.906 1.99,4.073 0.375,0.167 10 A
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Connect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) -Body ground None - Body ground Battery power supply Always 11 to 14 V
A-29 (ACC) -Body ground None - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-32 (IG) - Body ground None - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground None - Body ground Body ground Always Below 1 Ω



e.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*: w/o Entry and Start System

G78-23 (BDSU) - Body ground* R - Body ground Back door opener switch assembly signal Back door opener switch assembly off Pulse generation
Back door opener switch assembly on Below 1 V
G79-27 (PBDS) - Body ground R - Body ground Back door control switch signal Back door control switch off Pulse generation
Back door control switch on Below 1 V