Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0050769 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


TELEVISION CAMERA ASSEMBLY


a.
E240561E01
1.5,0.104 1.938,0.365 0.438,0.26 1.615,0.156 1.927,0.354 0.313,0.198 10 U6

Disconnect the U6 television camera assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U6-6 (CB+) - Body ground B - Body ground Power source Within 60 seconds of turning the ignition switch to ACC 5.5 to 7.05 V


c.

Reconnect the U6 television camera assembly connector.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U6-3 (CV+) - U6-2 (CV-) W - R Video signal Ignition switch ON
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(See waveform 1)
Ignition switch ON
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(See waveform 2)

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly*1 or navigation ECU sub-assembly*2 with the connector connected.


*1: w/o Navigation System

*2: w/ Navigation System



e.
E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly*1 or navigation ECU sub-assembly*2 with the connector connected.


*1: w/o Navigation System

*2: w/ Navigation System


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Terminal No. (Symbol) U6-3 (CV+) - U6-2 (CV-)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R

HINT:

The video waveform changes according to the image sent by the television camera assembly.



ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Terminal No. (Symbol) U6-3 (CV+) - U6-2 (CV-)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R

HINT:

The video waveform changes according to the image sent by the television camera assembly.