Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM3090E _59 Vehicle Exterior _008792 WINDOW / GLASS _0050246 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) Y

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the power window control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
4.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the LIN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Proceed to
DTCs are not output
DTCs are output



DTCs are not output

5.CHECK FOR DTC*

DTCs are output

5.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

b.

Clear the DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Clear DTCs
50002 124

c.

Recheck for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

Result:
Proceed to
DTCs are not output
DTCs are output



DTCs are not output

6.PROBLEM SYMPTOMS TABLE

DTCs are output

6.PROBLEM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in problem symptoms table
Fault is listed in problem symptoms table



Fault is not listed in problem symptoms table

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in problem symptoms table

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

8.ADJUST, REPAIR OR REPLACE
a.

Check if the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD), door glass or door glass run has been removed and reinstalled.


Result:
Result Proceed to
Front power window regulator motor assembly LH (for LHD), front power window regulator motor assembly RH (for RHD), door glass or door glass run has been removed and reinstalled. A
Front power window regulator motor assembly LH (for LHD), front power window regulator motor assembly RH (for RHD), door glass or door glass run has not been removed and reinstalled. B



A

9.INITIALIZE POWER WINDOW CONTROL SYSTEM

B

10.CONFIRMATION TEST
9.INITIALIZE POWER WINDOW CONTROL SYSTEM
a.

If the front door window regulator assembly (for driver door) has been removed and reinstalled, perform "Initialize Power Window Control System" for the driver door glass.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

HINT:

If "Initialize Power Window Control System" has not been performed, the auto operation function, jam protection function and key-off operation function will not operate or will operate incorrectly.



Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END