Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM3090E _59 Vehicle Exterior _008792 WINDOW / GLASS _0050246 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  B2311  Power Window Motor Malfunction  


DESCRIPTION

The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the power window regulator master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor and ECU functions.

This DTC is output when the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is malfunctioning, or the ECU built into the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction Either condition is met:
·

Front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is malfunctioning

·

When ECU in front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position


·

Front power window regulator motor assembly LH (for LHD)

·

Front power window regulator motor assembly RH (for RHD)

·

Incorrect installation of power window components

·

Overheated front power window regulator motor assembly LH (for LHD)

·

Overheated front power window regulator motor assembly RH (for RHD)



CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2311 is stored in the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD).

·

If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

·

If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been removed and installed, or if the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) was reused when the door glass or door glass run was replaced, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DATA LIST / ACTIVE TEST

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Driver door power window OFF, UP or DOWN -
HINT:

Up and down movement does not occur if the arrow is not pressed and held.


Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
OK:

Driver door power window motor operates.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

2.PERFORM INITIALIZATION

NG (for LHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG (for RHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

2.PERFORM INITIALIZATION
a.

Initialize the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM
3.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check that the driver door power window operates normally by opening and closing the window.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>OPERATION CHECK

OK:

Driver door power window motor operates.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

4.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

NG (for LHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG (for RHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

4.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.


Result:
Proceed to
Power window components are installed correctly
Power window components are installed incorrectly



Power window components are installed correctly

5.CHECK FOR DTC

Power window components are installed incorrectly

INSTALL PARTS CORRECTLY

5.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Wait for at least 10 seconds, and then turn the ignition switch to ON.


c.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

Result:
Proceed to
DTC B2311 is not output
DTC B2311 is output (for LHD)
DTC B2311 is output (for RHD)



DTC B2311 is not output

END

DTC B2311 is output (for LHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

DTC B2311 is output (for RHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH