Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM3090E _59 Vehicle Exterior _008792 WINDOW / GLASS _0050246 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  B2312  Power Window Switch Malfunction  


DESCRIPTION

The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the power window regulator master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor and ECU functions.

This DTC is stored when the ECU built into the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) determines that the power window regulator master switch assembly is stuck.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2312 Power Window Switch Malfunction Either condition is met:
·

Front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) stuck

·

Power window regulator master switch assembly held in same position for more than 20 seconds


·

Power window regulator master switch assembly

·

Front power window regulator motor assembly LH (for LHD)

·

Front power window regulator motor assembly RH (for RHD)

·

Harness or connector



WIRING DIAGRAM

B341195E01
2.563,3.49 4.479,3.833 1.917,0.344 10 Front Power Window Regulator Motor Assembly LH*1 2.552,4.146 4.479,4.49 1.927,0.344 10 Front Power Window Regulator Motor Assembly RH*2 2.573,3.302 4.104,3.5 1.531,0.198 10 J3*1, I3*2 1.875,1.885 2.792,2.083 0.917,0.198 10 DOOR D 3.802,1.594 4.417,1.792 0.615,0.198 10 AUTO 0.448,1.719 2.281,1.917 1.833,0.198 10 from Battery 0.031,0.667 1.865,0.865 1.833,0.198 10 from POWER Relay 1.823,0.854 3.052,1.052 1.229,0.198 10 P/W MAIN 3.75,2.354 4.365,2.552 0.615,0.198 10 DOWN 0.24,3.76 1.927,3.958 1.688,0.198 10 *1: for LHD 0.24,4.229 1.927,4.427 1.688,0.198 10 *2: for RHD 5.406,0.646 5.563,0.844 0.156,0.198 10 B 2.844,1.583 3,1.781 0.156,0.198 10 B 2.615,1.604 2.771,1.802 0.156,0.198 10 2 3.875,2.729 4.49,2.927 0.615,0.198 10 GND 3.969,1.958 4.583,2.156 0.615,0.198 10 UP 5.438,1.677 5.594,1.875 0.156,0.198 10 A 5.427,2.063 5.583,2.26 0.156,0.198 10 U 5.427,2.427 5.583,2.625 0.156,0.198 10 D 5.438,2.823 5.594,3.021 0.156,0.198 10 E 5.156,0.521 5.313,0.719 0.156,0.198 10 6 5.198,1.583 5.354,1.781 0.156,0.198 10 4 5.177,2.354 5.333,2.552 0.156,0.198 10 5 4.792,1.958 5.615,2.177 0.823,0.219 10 8*1, 1*2 5.375,3.302 6.906,3.5 1.531,0.198 10 J5*1, I5*2 5.333,3.5 7.031,4.396 1.698,0.896 10 Power Window Regulator Master Switch Assembly 4.792,2.729 5.75,2.917 0.958,0.188 10 1*1, 9*2 4.292,1.573 4.448,1.771 0.156,0.198 10 4 4.292,1.969 4.583,2.156 0.292,0.188 10 10 4.292,2.354 4.448,2.552 0.156,0.198 10 7 4.281,2.74 4.438,2.938 0.156,0.198 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 is stored in the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD).

·

If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

If DTC B2312 is not output again after the DTC has been cleared, the DTC was output due to the switch being held.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTC.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Clear DTCs
50002 124

b.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

Result:
Proceed to
DTC B2312 is not output
DTC B2312 is output



DTC B2312 is not output

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

DTC B2312 is output

2.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DATA LIST / ACTIVE TEST

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal ON or OFF ON: Driver door power window auto switch being operated
OFF: Driver door power window auto switch not being operated
-
D Door P/W Up SW Driver door power window manual up switch signal ON or OFF ON: Driver door power window manual up switch being operated
OFF: Driver door power window manual up switch not being operated
-
D Door P/W Down SW Driver door power window manual down switch signal ON or OFF ON: Driver door power window manual down switch being operated
OFF: Driver door power window manual down switch not being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Auto SW
D Door P/W Up SW
D Door P/W Down SW
50003 124 1,2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG (for LHD)
NG (for RHD)



OK (for LHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

OK (for RHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG (for LHD)

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH AND BODY GROUND)

NG (for RHD)

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH AND BODY GROUND)
a.

Disconnect the J5 power window regulator master switch assembly connector.


b.

Disconnect the J3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-8 (U) - J3-10 (UP) Always Below 1 Ω
J5-5 (D) - J3-7 (DOWN) Always Below 1 Ω
J5-4 (A) - J3-4 (AUTO) Always Below 1 Ω
J5-1 (E) - Body ground Always Below 1 Ω
J3-1 (GND) - Body ground Always Below 1 Ω
J5-8 (U) or J3-10 (UP) - Body ground Always 10 kΩ or higher
J5-5 (D) or J3-7 (DOWN) - Body ground Always 10 kΩ or higher
J5-4 (A) or J3-4 (AUTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Inspect the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH AND BODY GROUND)
a.

Disconnect the I5 power window regulator master switch assembly connector.


b.

Disconnect the I3 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-1 (U) - I3-10 (UP) Always Below 1 Ω
I5-5 (D) - I3-7 (DOWN) Always Below 1 Ω
I5-4 (A) - I3-4 (AUTO) Always Below 1 Ω
I5-9 (E) - Body ground Always Below 1 Ω
I3-2 (GND) - Body ground Always Below 1 Ω
I5-1 (U) or I3-10 (UP) - Body ground Always 10 kΩ or higher
I5-5 (D) or I3-7 (DOWN) - Body ground Always 10 kΩ or higher
I5-4 (A) or I3-4 (AUTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Inspect the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY