When the ignition switch is ON, the rear power window regulator motor assembly RH is operated by the rear power window regulator switch assembly RH.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check that the window lock switch is off before performing the following procedure.
Remove the rear power window regulator switch assembly RH.
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL
Inspect the rear power window regulator switch assembly RH.
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear power window regulator motor assembly RH.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
Inspect the rear power window regulator motor assembly RH.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly RH) |
Disconnect the rear power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K1-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect K3 the rear power window regulator motor assembly RH connector.
Disconnect K1 the rear power window regulator switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K3-1 (U) - K1-4 (U) | Always | Below 1 Ω |
| K3-2 (D) - K1-1 (D) | Always | Below 1 Ω |
| K3-1 (U) or K1-4 (U) - Body ground | Always | 10 kΩ or higher |
| K3-2 (D) or K1-1 (D) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K1 rear power window regulator switch assembly RH connector.
Disconnect the J5*1 or I5*2 power window regulator master switch assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-5 (SU) - J5-10 (U) | Always | Below 1 Ω |
| K1-2 (SD) - J5-18 (D) | Always | Below 1 Ω |
| K1-5 (SU) or J5-10 (U) - Body ground | Always | 10 kΩ or higher |
| K1-2 (SD) or J5-18 (D) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-5 (SU) - I5-16 (U) | Always | Below 1 Ω |
| K1-2 (SD) - I5-15 (D) | Always | Below 1 Ω |
| K1-5 (SU) or I5-16 (U) - Body ground | Always | 10 kΩ or higher |
| K1-2 (SD) or I5-15 (D) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG