Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR MAIN SWITCH(for RHD) › 2012.12–2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0050342 BLIND SPOT MONITOR MAIN SWITCH(for RHD) G

PARK ASSIST / MONITORING  BLIND SPOT MONITOR MAIN SWITCH(for RHD)  INSPECTION  


PROCEDURE

Hide 83950M 1.INSPECT TELLTALE LIGHT ASSEMBLY (BLIND SPOT MONITOR MAIN SWITCH)

a.
E269059C02
1.542,1.01 1.854,0.406 false 1.344,1.021 0.875,0.344 false 0,0 0.313,0.156 0.313,0.156 10 *a 1.885,0.302 2.042,0.5 0.156,0.198 10 D 0.469,0.26 0.927,0.438 0.458,0.177 10 LAPB
*a Component without harness connected
(Telltale Light Assembly (Blind Spot Monitor Main Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (D) - 9 (LAPB) Blind spot monitor main switch assembly on (not protruding) Below 1 Ω
8 (D) - 9 (LAPB) Blind spot monitor main switch assembly off (protruding) 10 kΩ or higher


If the result is not as specified, replace the telltale light assembly (blind spot monitor main switch).


b.

Check that the switch illuminates.

i.
E269059C03
2.167,1.75 1.781,1.271 false 1.188,1.698 1.635,1.26 false 1.354,1.021 1.063,0.406 false 2.896,1.75 2.448,1.26 false 0,0 0.313,0.156 0.313,0.156 10 *a 2.063,1.781 2.375,1.948 0.313,0.167 10 DIM 0.854,0.219 1.281,0.396 0.427,0.177 10 LAPB 1.063,1.729 1.354,1.917 0.292,0.188 10 ILL- 2.885,1.792 3.052,1.979 0.167,0.188 10 E
*a Component without harness connected
(Telltale Light Assembly (Blind Spot Monitor Main Switch))


Apply battery voltage to the telltale light assembly (blind spot monitor main switch) and check that the switch illuminates.

OK:
Connection Specified Condition
Battery positive (+) → Terminal 18 (DIM)
Battery negative (-) → Terminal 19 (ILL-)
Illuminates
Battery positive (+) → Terminal 18 (DIM)
Battery positive (+) → Terminal 9 (LAPB)
Battery negative (-) → Terminal 19 (ILL-)
Battery negative (-) → Terminal 13 (E)
Illuminates in dimmed state


If the result is not as specified, replace the telltale light assembly (blind spot monitor main switch).



c.

Check that the switch indicator illuminates.

i.
E269059C04
1.25,1.021 0.875,0.375 false 1.396,1.021 1.688,0.365 false 1.49,1.906 1.781,1.271 false 2.875,1.896 2.448,1.271 false 0,0 0.313,0.156 0.313,0.156 10 *a 1.521,0.188 1.958,0.365 0.438,0.177 10 LAPB 0.781,0.208 0.948,0.396 0.167,0.188 10 E 1.354,1.948 1.656,2.104 0.302,0.156 10 DIM 2.854,1.917 3.156,2.073 0.302,0.156 10 E
*a Component without harness connected
(Telltale Light Assembly (Blind Spot Monitor Main Switch))


Apply battery voltage to the telltale light assembly (blind spot monitor main switch) and check operation of the switch as shown in the table below.

OK:
Connection Switch Condition Specified Condition
Battery positive (+) → Terminal 9 (LAPB)
Battery negative (-) → Terminal 10 (E)
Blind spot monitor main switch assembly on (not protruding) Indicator Illuminates
Battery positive (+) → Terminal 9 (LAPB)
Battery positive (+) → Terminal 18 (DIM)
Battery negative (-) → Terminal 10 (E)
Battery negative (-) → Terminal 13 (E)
Blind spot monitor main switch assembly on (not protruding) Illuminates in dimmed state


If the result is not as specified, replace the telltale light assembly (blind spot monitor main switch).