33321
1.INSPECT NO. 1 OUTPUT SHAFT
Check the No. 1 output shaft for wear and damage.
Using a dial indicator, measure the No. 1 output shaft runout.
0.03 mm (0.00118 in.)
If the runout is more than the maximum, replace the No. 1 output shaft.
Using a micrometer, measure the journal diameter of the No. 1 output shaft journal surface.
| Item | Specified Condition |
|---|---|
| Journal A | 32.002 to 32.018 mm (1.2600 to 1.2605 in.) |
| Journal B | 35.984 to 36.000 mm (1.4167 to 1.4173 in.) |
| Journal C | 41.984 to 42.000 mm (1.6530 to 1.6535 in.) |
| Journal D | 41.989 to 42.000 mm (1.6532 to 1.6535 in.) |
| Journal E | 46.984 to 47.000 mm (1.8498 to 1.8503 in.) |
| Journal F | 36.002 to 36.018 mm (1.4174 to 1.4180 in.) |
If the outer diameter is not as specified, replace the No. 1 output shaft.
33335
2.INSPECT 1ST DRIVEN GEAR THRUST CLEARANCE
Using a dial indicator, measure the 1st driven gear thrust clearance.
0.10 to 0.35 mm (0.00394 to 0.01377 in.)
0.35 mm (0.01377 in.)
If the clearance is more than the maximum, replace the 1st driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33335
3.INSPECT 1ST DRIVEN GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 1st driven gear radial clearance.
0.015 to 0.068 mm (0.000591 to 0.00267 in.)
0.068 mm (0.00267 in.)
If the clearance is more than the maximum, replace the 1st driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33332
4.INSPECT 2ND DRIVEN GEAR THRUST CLEARANCE
Using a dial indicator, measure the 2nd driven gear thrust clearance.
0.11 to 0.46 mm (0.00434 to 0.0181 in.)
0.46 mm (0.0181 in.)
If the clearance is more than the maximum, replace the 2nd driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33332
5.INSPECT 2ND DRIVEN GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 2nd driven gear radial clearance.
0.015 to 0.048 mm (0.000591 to 0.00188 in.)
0.048 mm (0.00188 in.)
If the clearance is more than the maximum, replace the 2nd driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33423A
6.INSPECT 3RD DRIVEN GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 3rd driven gear thrust clearance.
0.11 to 0.54 mm (0.00434 to 0.0212 in.)
0.54 mm (0.0212 in.)
If the clearance is more than the maximum, replace the 3rd driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33423A
7.INSPECT 3RD DRIVEN GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 3rd driven gear radial clearance.
0.015 to 0.066 mm (0.000591 to 0.00259 in.)
0.066 mm (0.00259 in.)
If the clearance is more than the maximum, replace the 3rd driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33422B
8.INSPECT 4TH DRIVEN GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 4th driven gear thrust clearance.
0.10 to 0.65 mm (0.00394 to 0.0255 in.)
0.65 mm (0.0255 in.)
If the clearance is more than the maximum, replace the 4th driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33422B
9.INSPECT 4TH DRIVEN GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 4th driven gear radial clearance.
0.015 to 0.066 mm (0.000591 to 0.00259 in.)
0.066 mm (0.00259 in.)
If the clearance is more than the maximum, replace the 4th driven gear, needle roller bearing or No. 1 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33428C
10.INSPECT 5TH DRIVEN GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 5th driven gear thrust clearance.
0.10 to 0.55 mm (0.00394 to 0.0216 in.)
0.55 mm (0.0216 in.)
If the clearance is more than the maximum, replace the 5th driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33428C
11.INSPECT 5TH DRIVEN GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 5th driven gear radial clearance.
0.015 to 0.066 mm (0.000591 to 0.00259 in.)
0.066 mm (0.00259 in.)
If the clearance is more than the maximum, replace the 5th driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33429B
12.INSPECT 6TH DRIVEN GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 6th driven gear thrust clearance.
0.10 to 0.55 mm (0.00394 to 0.0216 in.)
0.55 mm (0.0216 in.)
If the clearance is more than the maximum, replace the 6th driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33429B
13.INSPECT 6TH DRIVEN GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 6th driven gear radial clearance.
0.015 to 0.066 mm (0.000591 to 0.00259 in.)
0.066 mm (0.00259 in.)
If the clearance is more than the maximum, replace the 6th driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33331
14.INSPECT REVERSE DRIVEN GEAR THRUST CLEARANCE
Using a feeler gauge, measure the reverse driven gear thrust clearance.
0.11 to 0.34 mm (0.00434 to 0.0133 in.)
0.34 mm (0.0133 in.)
If the clearance is more than the maximum, replace the reverse driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33331
15.INSPECT REVERSE DRIVEN GEAR RADIAL CLEARANCE
Using a dial indicator, measure the reverse driven gear radial clearance.
0.015 to 0.068 mm (0.000591 to 0.00267 in.)
0.068 mm (0.00267 in.)
If the clearance is more than the maximum, replace the reverse driven gear, needle roller bearing or No. 2 output shaft. Replace the part or parts determined to be the most likely cause of the problem.
33242F
16.INSPECT 1ST AND 2ND SHIFT FORK SHAFT
Using a micrometer, measure the 1st and 2nd shift fork shaft.
13.982 to 14.000 mm (0.5505 to 0.5511 in.)
13.982 mm (0.5505 in.)
If the outer diameter is less than the minimum, replace the 1st and 2nd shift fork shaft.
33243F
17.INSPECT 3RD AND 4TH SHIFT FORK SHAFT
Using a micrometer, measure the 3rd and 4th shift fork shaft.
13.982 to 14.000 mm (0.5505 to 0.5511 in.)
13.982 mm (0.5505 in.)
If the outer diameter is less than the minimum, replace the 3rd and 4th shift fork shaft.
33244J
18.INSPECT 5TH AND 6TH SHIFT FORK SHAFT
Using a micrometer, measure the 5th and 6th shift fork shaft.
13.982 to 14.000 mm (0.5505 to 0.5511 in.)
13.982 mm (0.5505 in.)
If the outer diameter is less than the minimum, replace the 5th and 6th shift fork shaft.
33245H
19.INSPECT REVERSE SHIFT FORK SHAFT
Using a micrometer, measure the reverse shift fork shaft.
13.982 to 14.000 mm (0.5505 to 0.5511 in.)
13.982 mm (0.5505 in.)
If the outer diameter is less than the minimum, replace the reverse shift fork shaft.
33246C
20.INSPECT NO. 5 GEAR SHIFT FORK SHAFT
Using a micrometer, measure the No. 5 gear shift fork shaft.
15.966 to 15.984 mm (0.6286 to 0.6292 in.)
15.966 mm (0.6286 in.)
If the outer diameter is less than the minimum, replace the No. 5 gear shift fork shaft.
33212A
21.INSPECT NO. 1 GEAR SHIFT FORK
Using a vernier caliper, measure the No. 1 gear shift fork.
9.50 to 9.80 mm (0.375 to 0.385 in.)
14.010 to 14.043 mm (0.5516 to 0.5528 in.)
If the diameter and thickness is not as specified, replace the No. 1 gear shift fork.
33213G
22.INSPECT NO. 2 GEAR SHIFT FORK
Using a vernier caliper, measure the No. 2 gear shift fork.
9.50 to 9.80 mm (0.375 to 0.385 in.)
14.010 to 14.043 mm (0.5516 to 0.5528 in.)
14.70 to 15.30 mm (0.579 to 0.602 in.)
If the diameter and thickness is not as specified, replace the No. 2 gear shift fork.
33214G
23.INSPECT NO. 3 GEAR SHIFT FORK
Using a vernier caliper, measure the No. 3 gear shift fork.
9.50 to 9.80 mm (0.375 to 0.385 in.)
14.010 to 14.043 mm (0.5516 to 0.5528 in.)
If the diameter and thickness is not as specified, replace the No. 3 gear shift fork.
33211
24.INSPECT REVERSE SHIFT FORK
Using a vernier caliper, measure the reverse shaft fork.
4.40 to 4.56 mm (0.174 to 0.179 in.)
14.010 to 14.043 mm (0.5516 to 0.5528 in.)
14.70 to 15.30 mm (0.579 to 0.602 in.)
If the diameter and thickness is not as specified, replace the reverse shaft fork.
33233A
25.INSPECT NO. 2 GEAR SHIFT HEAD
Using a vernier caliper, measure the No. 2 gear shift head.
13.994 to 14.054 mm (0.551 to 0.553 in.)
14.054 mm (0.553 in.)
If the inside diameter is more than the maximum, replace the No. 2 gear shift head.
33234A
26.INSPECT NO. 3 GEAR SHIFT HEAD
Using a vernier caliper, measure the No. 3 gear shift head.
15.994 to 16.054 mm (0.630 to 0.632 in.)
14.20 to 14.25 mm (0.560 to 0.561 in.)
16.054 mm (0.632 in.)
14.25 mm (0.561 in.)
If the inside diameter is more than the maximum, replace the No. 3 gear shift head.
33335
27.INSPECT 1ST DRIVEN GEAR
Using a cylinder gauge, measure the inside diameter of the 1st driven gear.
53.015 to 53.040 mm (2.0872 to 2.0881 in.)
53.040 mm (2.0881 in.)
If the inside diameter is more than the maximum, replace the 1st driven gear.
33332
28.INSPECT 2ND DRIVEN GEAR
Using a cylinder gauge, measure the inside diameter of the 2nd driven gear.
56.015 to 56.030 mm (2.2054 to 2.2059 in.)
56.030 mm (2.2059 in.)
If the inside diameter is more than the maximum, replace the 2nd driven gear.
33423A
29.INSPECT 3RD DRIVEN GEAR
Using a cylinder gauge, measure the inside diameter of the 3rd driven gear.
42.015 to 42.040 mm (1.6542 to 1.6551 in.)
42.040 mm (1.6551 in.)
If the inside diameter is more than the maximum, replace the 3rd driven gear.
33422B
30.INSPECT 4TH DRIVEN GEAR
Using a cylinder gauge, measure the inside diameter of the 4th driven gear.
48.015 to 48.040 mm (1.8904 to 1.8913 in.)
48.040 mm (1.8913 in.)
If the inside diameter is more than the maximum, replace the 4th driven gear.
33037B
31.INSPECT 1ST DRIVEN GEAR SYNCHRONIZER RING SET
Check for wear and damage.
Coat the 1st driven gear cone with gear oil.
Turn the synchronizer ring in both directions while pushing it against the 1st driven gear cone and check that it locks in both directions.
If the synchronizer ring does not lock, replace the synchronizer ring.
Using a feeler gauge, measure the clearance between the synchronizer ring back and gear spline end.
0.98 to 1.82 mm (0.0386 to 0.0716 in.)
0.98 mm (0.0386 in.)
If the clearance is less than the minimum, replace the 1st driven gear synchronizer ring set.
33037B
32.INSPECT 2ND DRIVEN GEAR SYNCHRONIZER RING SET
Check for wear and damage.
Coat the 2nd driven gear cone with gear oil.
Turn the synchronizer ring in both directions while pushing it against the 2nd driven gear cone and check that it locks in both directions.
If the synchronizer ring does not lock, replace the synchronizer ring.
Using a feeler gauge, measure the clearance between the synchronizer ring back and 2nd gear spline end.
1.08 to 1.92 mm (0.0426 to 0.0755 in.)
1.08 mm (0.0426 in.)
If the clearance is less than the minimum, replace the 2nd driven gear synchronizer ring set.
33047
33.INSPECT 3RD DRIVEN GEAR SYNCHRONIZER RING SET
Check for wear and damage.
Coat the 3rd driven gear cone with gear oil.
Turn the synchronizer ring in both directions while pushing it against the 3rd driven gear cone and check that it locks in both directions.
If the synchronizer ring does not lock, replace the synchronizer ring.
Using a feeler gauge, measure the clearance between the 3rd gear synchronizer ring back and spline end.
1.00 to 2.00 mm (0.0394 to 0.0787 in.)
1.00 mm (0.0394 in.)
If the clearance is less than the minimum, replace the 3rd driven gear synchronizer ring set.
34.INSPECT 4TH DRIVEN GEAR SYNCHRONIZER RING SET
Check for wear and damage.
Coat the 4th driven gear cone with gear oil.
Turn the synchronizer ring in both directions while pushing it against the 4th driven gear cone and check that it locks in both directions.
If the synchronizer ring does not lock, replace the synchronizer ring.
Using a feeler gauge, measure the clearance between the 4th gear synchronizer ring back and spline end.
0.92 to 1.88 mm (0.0363 to 0.0740 in.)
0.92 mm (0.0363 in.)
If the clearance is less than the minimum, replace the 4th driven gear synchronizer ring set.
33363
35.INSPECT NO. 1 TRANSMISSION HUB SLEEVE
Using a vernier caliper, measure the clearance between the No. 1 transmission hub sleeve and the No. 1 gear shift fork.
0.10 to 0.50 mm (0.00394 to 0.0196 in.)
If the clearance is not as specified, replace the No. 1 transmission hub sleeve and No. 1 gear shift fork.
33364
36.INSPECT NO. 2 TRANSMISSION HUB SLEEVE
Using a vernier caliper, measure the clearance between the No. 2 transmission hub sleeve and the No. 2 gear shift fork.
0.10 to 0.50 mm (0.00394 to 0.0196 in.)
If the clearance is not as specified, replace the No. 2 transmission hub sleeve and No. 2 gear shift fork.
33322
37.INSPECT NO. 2 OUTPUT SHAFT
Check the No. 2 output shaft for wear and damage.
Using a dial indicator, check the No. 2 output shaft runout.
0.03 mm (0.00118 in.)
If the runout is more than the maximum, replace the No. 2 output shaft.
Using a micrometer, measure the journal diameter of the No. 2 output shaft journal surface.
| Item | Specified Condition |
|---|---|
| Journal A | 32.002 to 32.018 mm (1.2600 to 1.2605 in.) |
| Journal B | 35.984 to 36.000 mm (1.4167 to 1.4173 in.) |
| Journal C | 41.984 to 42.000 mm (1.6530 to 1.6535 in.) |
| Journal D | 46.984 to 47.000 mm (1.8498 to 1.8503 in.) |
| Journal E | 35.002 to 35.018 mm (1.3781 to 1.3786 in.) |
If the outer diameter is not as specified, replace the No. 2 output shaft.
33428C
38.INSPECT 5TH DRIVEN GEAR
Using a cylinder gauge, measure the inside diameter of the 5th driven gear.
48.015 to 48.040 mm (1.890 to 1.891 in.)
48.040 mm (1.891 in.)
If the inside diameter is more than the maximum, replace the 5th driven gear.
33429B
39.INSPECT 6TH DRIVEN GEAR
Using a cylinder gauge, measure the inside diameter of the 6th driven gear.
42.015 to 42.040 mm (1.6542 to 1.6551 in.)
42.040 mm (1.6551 in.)
If the inside diameter is more than the maximum, replace the 6th driven gear.
33331
40.INSPECT REVERSE DRIVEN GEAR
Using a cylinder gauge, measure the inside diameter of the reverse driven gear.
53.015 to 53.040 mm (2.0873 to 2.0881 in.)
53.040 mm (2.0881 in.)
If the inside diameter is more than the maximum, replace the reverse driven gear.
41.INSPECT 5TH DRIVEN SYNCHRONIZER RING SET
Check for wear and damage.
Coat the 5th driven gear cone with gear oil.
Turn the synchronizer ring in both directions while pushing it against the 5th driven gear cone and check that it locks in both directions.
If the synchronizer ring does not lock, replace the synchronizer ring.
Using a feeler gauge, measure the clearance between the synchronizer ring back and 5th driven gear spline end.
0.80 to 1.60 mm (0.0315 to 0.0629 in.)
0.80 mm (0.0315 in.)
If the clearance is less than the minimum, replace the 5th driven gear synchronizer ring set.
33369B
42.INSPECT 6TH DRIVEN SYNCHRONIZER RING SET
Check for wear and damage.
Coat the 6th driven gear cone with gear oil.
Turn the synchronizer ring in both directions while pushing it against the 6th driven gear cone and check that it locks in both directions.
If the synchronizer ring does not lock, replace the synchronizer ring.
Using a feeler gauge, measure the clearance between the gear synchronizer ring back and 6th driven gear spline end.
0.80 to 1.60 mm (0.0315 to 0.0629 in.)
0.80 mm (0.0315 in.)
If the clearance is less than the minimum, replace the 6th driven gear synchronizer ring set.
33369B
43.INSPECT REVERSE DRIVEN GEAR SYNCHRONIZER RING SET
Check for wear and damage.
Coat the reverse driven gear cone with gear oil.
Turn the synchronizer ring in both directions while pushing it against the reverse driven gear cone and check that it locks in both directions.
If the synchronizer ring does not lock, replace the synchronizer ring.
Using a feeler gauge, measure the clearance between the synchronizer ring back and reverse driven gear spline end.
0.68 to 1.32 mm (0.0268 to 0.0519 in.)
0.68 mm (0.0268 in.)
If the clearance is less than the minimum, replace the reverse driven gear synchronizer ring set.
33395
44.INSPECT NO. 3 TRANSMISSION HUB SLEEVE
Using a vernier caliper, measure the clearance between the No. 3 transmission hub sleeve and the No. 3 gear shift fork.
0.10 to 0.50 mm (0.00394 to 0.0196 in.)
If the clearance is not as specified, replace the No. 3 transmission hub sleeve and No. 3 gear shift fork.
33327
45.INSPECT NO. 4 TRANSMISSION HUB SLEEVE
Using a vernier caliper, measure the clearance between the No. 4 transmission hub sleeve and the reverse shift fork.
0.15 to 0.41 mm (0.00591 to 0.0161 in.)
If the clearance is not as specified, replace the No. 4 transmission hub sleeve and reverse shift fork.