Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048163 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the back door only, the request code may not be being transmitted from the back door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU [smart key ECU assembly] and electrical key antenna [outside luggage]), or there may be electric wave interference.

WIRING DIAGRAM

B341304E02
6.063,2.865 6.677,3.063 0.615,0.198 10 TSW5 6.063,2.427 6.677,2.625 0.615,0.198 10 TSW6 5.708,2.26 6.052,2.458 0.344,0.198 10 28 5.74,2.75 6.083,2.948 0.344,0.198 10 27 5.542,3.406 5.885,3.604 0.344,0.198 10 G83 5.885,0.302 6.229,0.5 0.344,0.198 10 2 5.885,0.75 6.229,0.948 0.344,0.198 10 1 6.052,0.448 6.667,0.646 0.615,0.198 10 CLG8 6.063,0.896 6.677,1.094 0.615,0.198 10 CG8B 2.427,0.302 2.771,0.5 0.344,0.198 10 1 2.427,0.76 2.771,0.958 0.344,0.198 10 2 1.844,0.396 2.479,0.625 0.635,0.229 10 ANTE8 1.865,0.885 2.49,1.104 0.625,0.219 10 CLGB 0.969,1.552 3.01,1.917 2.042,0.365 10 Electrical Key Antenna (Outside Luggage) 1.01,1.344 1.635,1.563 0.625,0.219 10 T2 1.042,3.365 1.667,3.583 0.625,0.219 10 U7 1.01,3.552 3.635,3.927 2.625,0.375 10 Back Door Opener Switch Assembly 5.531,3.583 7.125,4.25 1.594,0.667 10 Certification ECU (Smart Key ECU Assembly) 2.677,2.281 3.021,2.479 0.344,0.198 10 1 2.667,2.729 3.01,2.927 0.344,0.198 10 3 2.479,2.292 2.823,2.49 0.344,0.198 10 L 2.375,2.771 2.719,2.969 0.344,0.198 10 UL 1.563,2.521 2.625,2.74 1.063,0.219 10 Lock Switch 1.542,3.031 2.938,3.281 1.396,0.25 10 Unlock Switch 1.302,2.75 1.646,2.948 0.344,0.198 10 E 1.115,2.76 1.458,2.958 0.344,0.198 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When the entry lock and unlock functions do not operate for doors other than the driver door and if the engine switch has not been turned on (IG) for 14 days or more, lock/unlock the doors using the wireless door lock function or key linked unlock operation and then check if the entry door lock and unlock functions operate.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Proceed to
Door locks operate normally
Door locks do not operate



Door locks operate normally

2.CHECK WAVE ENVIRONMENT

Door locks do not operate

2.CHECK WAVE ENVIRONMENT
a.
B340888C01
1.833,1.188 2.146,1.385 0.313,0.198 10 *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage) and perform an entry back door unlock function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result:
Proceed to
Entry function does not operate normally
Entry function operates normally



Entry function does not operate normally

3.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY

Entry function operates normally

AFFECTED BY WAVE INTERFERENCE

3.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Remove the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL


b.

Inspect back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH - BODY GROUND)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH - BODY GROUND)
a.
B203524C03
1.5,0.167 1.875,0.438 0.375,0.271 1.708,1.802 1.708,1.365 false 1.708,1.813 2.125,1.813 false 1.604,0.219 1.917,0.417 0.313,0.198 10 U7 0.167,0.125 0.479,0.323 0.313,0.198 10 *a 2.177,1.708 2.417,1.979 0.24,0.271 10 E
*a Front view of wire harness connector
(to Back Door Opener Switch Assembly)


Disconnect the back door opener switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U7-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK KEY DIAGNOSTIC MODE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.


b.
B340888C01
1.833,1.188 2.146,1.385 0.313,0.198 10 *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.

Check the electrical key antenna (outside luggage).

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
Diagnostic mode inspections fail
Diagnostic mode inspections succeed



Diagnostic mode inspections fail

6.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

Diagnostic mode inspections succeed

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the T2 electrical key antenna (outside luggage) connector.


b.

Disconnect the G83 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T2-1 (ANTE8) - G83-2 (CLG8) Always Below 1 Ω
T2-2 (CLGB) - G83-1 (CG8B) Always Below 1 Ω
T2-1 (ANTE8) or G83-2 (CLG8) - Body ground Always 10 kΩ or higher
T2-2 (CLGB) or G83-1 (CG8B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.
B226391N15
1.823,1.073 2.219,0.708 2.219,0.708 2.406,0.708 false 1.594,1.083 1.198,0.719 1.198,0.719 1.021,0.719 false 2.469,0.615 3.01,0.813 0.542,0.198 10 CLGB 0.417,0.635 0.99,0.823 0.573,0.188 10 ANTE8

Remove the electrical key antenna (outside luggage).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ANTE8) - 2 (CLGB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG