The main body ECU (multiplex network body ECU) receives headlight dimmer switch information signals and illuminates the front fog lights.
Inspect the bulbs and fuses for circuits related to this system before performing the following inspection procedure.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
Headlight relay operates (low beam headlights come on).
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Fog Light Relay | Front fog light relay | ON or OFF | The headlight dimmer switch is in the tail position. |
| Tester Display |
|---|
| Front Fog Light Relay |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Remove the front fog light relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front fog light relay from the No. 2 engine room relay block and junction block assembly.
| *A | w/o Side Marker Light | *B | w/ Side Marker Light |
| *a | Front view of wire harness connector
(to Front Fog Light Relay) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Front fog light relay terminal 3 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front fog light from the No. 2 engine room relay block and junction block assembly.
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Front fog light relay terminal 1 - 3B-28 | Always | Below 1 Ω |
| 3B-28 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front fog light from the No. 2 engine room relay block and junction block assembly.
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Front fog light relay terminal 2 - 3B-56 | Always | Below 1 Ω |
| 3B-56 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A-13 (FFGO) - 3B-56 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL