Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2012.12–2015.10
RM3090E _59 Vehicle Exterior _008430 LIGHTING (EXT) _0047053 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives headlight dimmer switch information signals and illuminates the rear fog lights.

WIRING DIAGRAM

E270523E02
3.094,1.667 4.031,1.917 0.938,0.25 10 false from Battery 0.688,2.958 1.031,3.167 0.344,0.208 10 false S5 0.688,3.115 2.573,3.365 1.885,0.25 10 false Rear Fog Light Assembly LH 0.698,4.833 2.583,5.083 1.885,0.25 10 false Rear Fog Light Assembly RH 0.688,4.677 1.031,4.885 0.344,0.208 10 false S6 6.188,2.938 6.729,3.167 0.542,0.229 10 false RFGO 5.25,2.542 5.917,2.781 0.667,0.24 10 false FOG RR 3.802,4.042 4.344,4.271 0.542,0.229 10 false TAIL 4.542,3.885 5.802,4.125 1.26,0.24 10 false from TAIL Relay 3.677,3.198 4.417,3.417 0.74,0.219 10 false FOG RR 3.469,2.323 3.677,2.531 0.208,0.208 10 false 3 4.271,2.313 4.552,2.521 0.281,0.208 10 false 5 4.271,2.792 4.552,3 0.281,0.208 10 false 2 3.469,2.802 3.75,3.01 0.281,0.208 10 false 1 4.938,1.469 5.219,1.677 0.281,0.208 10 false 1 4.896,1.677 5.219,1.885 0.323,0.208 10 false 3A 4.896,2.417 5.219,2.625 0.323,0.208 10 false 3C 4.896,2.906 5.219,3.115 0.323,0.208 10 false 3D 4.906,2.219 5.188,2.427 0.281,0.208 10 false 25 5.885,2.792 6.167,3 0.281,0.208 10 false 27 3.49,4.74 5.083,5.177 1.594,0.438 10 false Instrument Panel Junction Block Assembly 3.208,3.917 3.635,4.115 0.427,0.198 10 false 3C 3.219,3.708 3.521,3.927 0.302,0.219 10 false 38 4.896,2.719 5.177,2.927 0.281,0.208 10 false 52 2.167,2.292 2.448,2.5 0.281,0.208 10 false 1 2.167,4.01 2.448,4.219 0.281,0.208 10 false 1 0.552,2.323 0.813,2.573 0.26,0.25 10 false 2 0.542,4.042 0.802,4.292 0.26,0.25 10 false 2 4.917,5.542 5.458,5.771 0.542,0.229 10 false A 4.906,5.698 7.073,6.135 2.167,0.438 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the bulbs and fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (REAR FOG LIGHT RELAY)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light relay ON or OFF The headlight dimmer switch is in the tail position.
Body Electrical > Main Body > Active Test
Tester Display
Rear Fog Light Relay
50004 123 17
OK:

Rear fog light relay operates (rear fog lights come on).



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT REAR FOG LIGHT RELAY (FOG RR)
2.INSPECT REAR FOG LIGHT RELAY (FOG RR)
a.
E270109N02
1.948,1.302 2.135,1.302 false 2.698,1.302 2.885,1.302 false 2.542,1.021 2.865,1.021 false 2.552,0.76 2.875,0.76 false 0.458,0.719 0.615,0.917 0.156,0.198 10 3 1.271,0.719 1.427,0.917 0.156,0.198 10 5 1.271,1.281 1.427,1.479 0.156,0.198 10 2 0.458,1.281 0.615,1.479 0.156,0.198 10 1 2.927,0.677 3.083,0.875 0.156,0.198 10 3 2.917,0.938 3.073,1.135 0.156,0.198 10 5 2.948,1.229 3.104,1.427 0.156,0.198 10 1 1.813,1.24 1.969,1.438 0.156,0.198 10 2

Remove the rear fog light relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)

NG

REPLACE REAR FOG LIGHT RELAY (FOG RR)

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
a.
E270517C01
0.5,0.969 0.896,1.198 0.396,0.229 0.125,0.063 0.438,0.219 0.313,0.156 10 *a 0.615,1.01 0.927,1.167 0.313,0.156 10 3A
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Remove the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY [FOG RR] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY [FOG RR] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the rear fog light relay from the No. 4 relay block.


b.

Disconnect the 3C and 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Rear fog light relay terminal 5 - 3C-25 Always Below 1 Ω
Rear fog light relay terminal 2 - 3D-52 Always Below 1 Ω
Rear fog light relay terminal 1 - 3C-38 Always Below 1 Ω
3C-25 - Body ground Always 10 kΩ or higher
3D-52 - Body ground Always 10 kΩ or higher
3C-38 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E270524N01
1.063,0.5 1.417,0.75 0.354,0.25 0.177,1.604 0.531,1.854 0.354,0.25 0.156,2.729 0.51,2.979 0.354,0.25 1.531,3.573 1.885,3.823 0.354,0.25 2.552,4.24 2.552,4.052 false 1.125,0.552 1.438,0.75 0.313,0.198 10 3A 0.25,1.656 0.563,1.854 0.313,0.198 10 3C 0.24,2.76 0.552,2.958 0.313,0.198 10 3D 1.656,3.615 1.969,3.813 0.313,0.198 10 A 2.354,4.271 2.854,4.448 0.5,0.177 10 RFGO

Remove the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3A-1 - 3C-25 Always Below 1 Ω
A-27 (RFGO) - 3D-52 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG