The ECM receives a signal from the turbine speed sensor (transmission revolution sensor (NT)) installed in the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.
The transmission revolution sensor (NT) detects the continuously variable transaxle input shaft speed and sends it to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0715 | Input/Turbine Speed Sensor "A" Circuit | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
A transmission revolution sensor (NT) signal malfunction is not detected. 2.
The transmission revolution sensor (NT) output voltage is less than 0.1 V, or higher than 1.9 V. 3.
2 seconds 4.
1 trip detection logic |
·
Open or short in transmission revolution sensor (NT) circuit ·
Transmission revolution sensor (NT) ·
ECM |
Comes on | DTC stored |
| P0717 | Input/Turbine Speed Sensor "A" Circuit No Signal | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error is detected in the park/neutral position switch. 2.
The speed indicated by the transmission revolution sensor (NT) is less than 300 rpm. 3.
2 seconds 4.
1 trip detection logic |
·
Open or short in transmission revolution sensor (NT) circuit ·
Transmission revolution sensor (NT) ·
ECM |
Comes on | DTC stored |
The turbine speed sensor detects the transaxle input shaft speed. The ECM determines the necessary gear ratio based on a comparison of the turbine speed sensor (input shaft speed) with the output speed sensor (output shaft speed).
When the output shaft speed is higher than the expected value and the input shaft speed is less than 300 rpm while driving with the shift lever in D, the ECM will conclude that there is a malfunction in the transmission revolution sensor (NT). The ECM will illuminate the MIL and store the DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| SPD (NT) |
| NT Sensor Voltage |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| SPD (NT) | Input turbine speed | min.: 0 rpm
max.: 12750 rpm |
·
Lock-up on (After warming up engine): Input turbine speed (NT) equal to engine speed ·
Lock-up off (Idling with shift lever in P or N): Input turbine speed (NT) nearly equal to engine speed ·
Vehicle stopped with shift lever in R: 0 rpm |
Data is displayed in increments of 50 rpm. |
| NT Sensor Voltage | Input turbine speed (NT) sensor output voltage | min.: 0 V
max.: 4.999 V |
Engine idling (Vehicle stopped with shift lever in P or N): 0.6 to 1.5 V | - |
In accordance with the display on the GTS, read the Data List.
| Proceed to |
|---|
| Data displayed is not as specified under Normal Condition |
| Data displayed is as specified under Normal Condition |
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition
Remove the transmission revolution sensor (NT).
Click hereDrivetrain>K111F MULTIDRIVE / CVT>REVOLUTION SENSOR>REMOVAL
| *1 | Transmission Revolution Sensor (NT) | *2 | Ammeter |
| *3 | Battery | - | - |
| *a | 5 mm (0.197 in.) Gap or Closer | - | - |
Connect the battery to the sensor as shown in the illustration.
Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) gap or closer) to change the high/low signals while measuring the current.
Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.
Measure the current according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (NTO) - 2 (NTB) | Low signal | 4 to 8 mA |
| 1 (NTO) - 2 (NTB) | High signal | 12 to 16 mA |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B33 transmission revolution sensor (NT) connector.
Disconnect the B75 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B33-1 (NTO) - B75-125 (NTO) | Always | Below 1 Ω |
| B33-2 (NTB) - B75-126 (NTB) | Always | Below 1 Ω |
| B33-1 (NTO) or B75-125 (NTO) - Body ground | Always | 10 kΩ or higher |
| B33-2 (NTB) or B75-126 (NTB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE:
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT