Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0720  Output Speed Sensor Circuit  P0722  Output Speed Sensor Circuit No Signal  


DESCRIPTION

The ECM receives a signal from the secondary pulley speed sensor (transmission revolution sensor (NOUT)) installed in the continuously variable transaxle and determines the output shaft speed in order to control the gear ratio.

The transmission revolution sensor (NOUT) detects the continuously variable transaxle output shaft speed and sends it to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0720 Output Speed Sensor Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

A transmission revolution (NOUT) signal malfunction is not detected.

2.

The transmission revolution sensor (NOUT) output voltage is less than 0.1 V, or higher than 1.9 V.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NOUT) circuit

·

Transmission revolution sensor (NOUT)

·

ECM


Comes on DTC stored
P0722 Output Speed Sensor Circuit No Signal 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error is detected in the park/neutral position switch.

2.

The speed indicated by the transmission revolution sensor (NOUT) is less than 300 rpm.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NOUT) circuit

·

Transmission revolution sensor (NOUT)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM receives a signal from the secondary pulley speed sensor (transmission revolution sensor (NOUT)) installed in the continuously variable transaxle and determines the output shaft speed in order to control the gear ratio.

If the ECM detects no signal from the secondary pulley speed sensor even while the vehicle is moving, it will conclude that there is a malfunction in the secondary pulley speed sensor. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C277072E02
0.719,3.01 3.302,3.26 2.583,0.25 10 Transmission Revolution Sensor (NOUT) 2.229,1.125 2.74,1.344 0.51,0.219 10 NOTO 2.229,2.083 2.771,2.292 0.542,0.208 10 NOTB 2.75,1.365 2.99,1.594 0.24,0.229 10 1 2.75,2.344 2.99,2.573 0.24,0.229 10 2 5.229,1.375 5.625,1.573 0.396,0.198 10 129 5.604,2.219 6.094,2.438 0.49,0.219 10 NOTB 5.604,1.24 6.125,1.458 0.521,0.219 10 NOTO 0.729,2.781 1.125,2.979 0.396,0.198 10 B31 5.219,2.344 5.615,2.542 0.396,0.198 10 130 5.792,3.188 6.188,3.385 0.396,0.198 10 ECM 5.802,3 6.198,3.198 0.396,0.198 10 B75

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SPD (NOUT) AND NOUT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
SPD (NOUT)
NOUT Sensor Voltage
50003 234 402,403
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NOUT) Secondary pulley speed (NOUT) min.: 0 rpm
max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Vehicle cruising at approx. 60 km/h (37 mph): 2850 rpm


Data is displayed in increments of 50 rpm.
NOUT Sensor Voltage Secondary pulley speed (NOUT) sensor output voltage min.: 0.000 V
max.: 4.999 V
Engine idling: Approx. 2 V -

e.

In accordance with the display on the GTS, read the Data List.

Result:
Proceed to
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition




Data displayed is not as specified under Normal Condition

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

Data displayed is as specified under Normal Condition

4.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)
a.

Remove the transmission revolution sensor (NOUT).

Click hereDrivetrain>K111F MULTIDRIVE / CVT>REVOLUTION SENSOR>REMOVAL

C277851C03
1.333,1.958 1.594,1.469 true 4.521,1.156 4.229,0.979 true 3.667,1.146 3.948,0.969 true 2.063,1.948 1.802,1.469 true 6.115,1.24 5.813,1.01 true 4.906,0.844 4.813,0.552 true 4.698,2.563 4.927,2.302 false 4.99,0.781 5.302,0.938 0.313,0.156 10 false *2 6.198,1.188 6.51,1.385 0.313,0.198 10 false *3 1,0.563 1.313,0.719 0.313,0.156 10 false *1 4.49,2.479 4.802,2.635 0.313,0.156 10 false *a 1.094,2.01 1.583,2.229 0.49,0.219 10 false NOTB 1.979,2.01 2.479,2.25 0.5,0.24 10 false NOTO 4.583,1.094 4.771,1.292 0.188,0.198 10 false 1 3.552,1.083 3.74,1.281 0.188,0.198 10 false 2
*1 Transmission Revolution Sensor (NOUT) *2 Ammeter
*3 Battery - -
*a 5 mm (0.197 in.) Gap or Closer - -



b.

Connect the battery to the sensor as shown in the illustration.


c.

Wave a magnetic object left and right in front of the transmission revolution sensor tip (5 mm (0.197 in.) gap or closer) to change the high/low signals while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. Current will not change without waving the magnetic object as indicated by the arrow in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NOTO) - 2 (NOTB) Low signal 4 to 8 mA
1 (NOTO) - 2 (NOTB) High signal 12 to 16 mA



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NOUT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - ECM)
a.

Disconnect the B31 transmission revolution sensor (NOUT) connector.


b.

Disconnect the B75 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B31-1 (NOTO) - B75-129 (NOTO) Always Below 1 Ω
B31-2 (NOTB) - B75-130 (NOTB) Always Below 1 Ω
B31-1 (NOTO) or B75-129 (NOTO) - Body ground Always 10 kΩ or higher
B31-2 (NOTB) or B75-130 (NOTB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT