Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0842  Transmission Fluid Pressure Sensor/Switch "A" Circuit Low  P0843  Transmission Fluid Pressure Sensor/Switch "A" Circuit High  


DESCRIPTION

The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is detected by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0842 Transmission Fluid Pressure Sensor/Switch "A" Circuit Low 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

2 seconds or more have elapsed after the engine is started.

2.

There is a short circuit in the oil pressure sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Short in oil pressure sensor circuit

·

Oil pressure sensor

·

ECM


Comes on (w/ OBD)
- (w/o OBD)
DTC stored
P0843 Transmission Fluid Pressure Sensor/Switch "A" Circuit High 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

2 seconds or more have elapsed after the engine is started.

2.

There is an open circuit in the oil pressure sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Open in oil pressure sensor circuit

·

Oil pressure sensor

·

ECM


Comes on (w/ OBD)
- (w/o OBD)
DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short circuit in the oil pressure sensor circuit. When there is an open or short circuit in the oil pressure sensor circuit, the ECM detects the problem, illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C277073E01
1.385,2.792 1.698,3.01 0.313,0.219 10 B32 1.375,3.01 2.729,3.25 1.354,0.24 10 Oil Pressure Sensor 2.385,1.25 2.698,1.469 0.313,0.219 10 VC 2.313,1.729 2.708,1.948 0.396,0.219 10 PTO 2.406,2.219 2.719,2.438 0.313,0.219 10 E2 2.75,1.375 3.063,1.594 0.313,0.219 10 3 2.75,1.865 3.063,2.083 0.313,0.219 10 2 2.74,2.354 3.052,2.573 0.313,0.219 10 1 5.625,1.74 6.021,1.958 0.396,0.219 10 PTO 5.615,2.229 6.125,2.448 0.51,0.219 10 EPTO 5.625,1.25 6.135,1.469 0.51,0.219 10 VCPT 5.25,1.385 5.604,1.615 0.354,0.229 10 120 5.313,1.865 5.667,2.094 0.354,0.229 10 89 5.24,2.344 5.594,2.573 0.354,0.229 10 121 5.813,2.99 6.167,3.219 0.354,0.229 10 B75 5.813,3.198 6.323,3.417 0.51,0.219 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (A/T OIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value min.: -64 MPa
max.: 63.998 MPa
Secondary oil pressure inspection
3ZR-FAE:
·

D position stall speed test: 3.3 to 4.6 MPa

·

R position stall speed test: 3.0 to 3.7 MPa


3ZR-FE:
·

D position stall speed test: 3.2 to 4.5 MPa

·

R position stall speed test: 3.0 to 3.5 MPa


-

e.

In accordance with the display on the GTS, read the Data List.

Result:
Proceed to
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition




Data displayed is not as specified under Normal Condition

2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)

Data displayed is as specified under Normal Condition

5.REPLACE ECM
2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)
a.

Disconnect the B32 oil pressure sensor connector.


b.

Disconnect the B75 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B32-1 (E2) - B75-121 (EPTO) Always Below 1 Ω
B32-2 (PTO) - B75-89 (PTO) Always Below 1 Ω
B32-3 (VC) - B75-120 (VCPT) Always Below 1 Ω
B32-1 (E2) or B75-121 (EPTO) - Body ground Always 10 kΩ or higher
B32-2 (PTO) or B75-89 (PTO) - Body ground Always 10 kΩ or higher
B32-3 (VC) or B75-120 (VCPT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VCPT TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VCPT TERMINAL VOLTAGE)
a.
C199166C01
0.469,1.021 0.906,1.281 0.438,0.26 1.229,1.729 1.531,1.219 true 2.198,1.74 1.906,1.229 true 0.125,0.083 0.344,0.281 0.219,0.198 10 *a 0.573,1.073 0.948,1.302 0.375,0.229 10 B32 1.104,1.781 1.344,1.979 0.24,0.198 10 E2 2.156,1.76 2.427,1.958 0.271,0.198 10 VC
*a Front view of wire harness connector
(to Oil Pressure Sensor)


Disconnect the oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B32-1 (E2) - B32-3 (VC) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

4.REPLACE OIL PRESSURE SENSOR

NG

5.REPLACE ECM
4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT