Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Shift Paddle Switch Circuit  


DESCRIPTION

When the shift lever is in M, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.

WIRING DIAGRAM

C280945E01
2.406,0.479 4.542,0.75 2.135,0.271 10 to Transmission Control Switch 0.208,2.292 1.833,2.802 1.625,0.51 10 Shift Paddle Switch RH (Transmission Shift Switch Assembly) 0.219,4.573 1.844,5.094 1.625,0.521 10 Shift Paddle Switch LH (Transmission Shift Switch Assembly) 1.542,1.5 2,1.74 0.458,0.24 10 SFTU 2.031,1.5 2.49,1.74 0.458,0.24 10 SFTU 6.313,1.615 6.771,1.854 0.458,0.24 10 SFTU 4.708,1.49 5.167,1.729 0.458,0.24 10 SUP 3.604,1.49 4.063,1.729 0.458,0.24 10 SUP 2.521,1.5 2.979,1.74 0.458,0.24 10 SFTU 1.542,1.854 2,2.094 0.458,0.24 10 ECC1 2.021,1.844 2.479,2.083 0.458,0.24 10 ECC1 2.021,3.719 2.479,3.958 0.458,0.24 10 ECC1 1.604,4.073 2.063,4.313 0.458,0.24 10 ECC 1.552,3.719 2.01,3.958 0.458,0.24 10 ECC1 2.01,4.063 2.469,4.302 0.458,0.24 10 ECC 2.552,4.063 3.01,4.302 0.458,0.24 10 ECC 3.594,4.073 4.052,4.313 0.458,0.24 10 ECC 4.708,4.073 5.167,4.313 0.458,0.24 10 ECC 1.563,3.396 2.021,3.635 0.458,0.24 10 SFTD 2.042,3.385 2.5,3.625 0.458,0.24 10 SFTD 2.531,3.385 2.99,3.625 0.458,0.24 10 SFTD 3.625,3.375 4.083,3.615 0.458,0.24 10 SDN 4.729,3.385 5.188,3.625 0.458,0.24 10 SDN 6.281,3.5 6.74,3.74 0.458,0.24 10 SFTD 4.083,1.615 4.542,1.854 0.458,0.24 10 z1 4.083,3.51 4.542,3.75 0.458,0.24 10 z1 4.073,4.198 4.531,4.438 0.458,0.24 10 z1 5.146,4.198 5.604,4.438 0.458,0.24 10 G8 5.146,3.51 5.604,3.75 0.458,0.24 10 G8 5.146,1.615 5.604,1.854 0.458,0.24 10 G8 6.01,1.76 6.333,2.01 0.323,0.25 10 42 6,3.656 6.323,3.906 0.323,0.25 10 43 5.156,1.396 5.479,1.646 0.323,0.25 10 14 4.104,1.396 4.427,1.646 0.323,0.25 10 6 4.073,3.271 4.396,3.521 0.323,0.25 10 12 4.104,3.958 4.427,4.208 0.323,0.25 10 7 5.198,3.969 5.521,4.219 0.323,0.25 10 2 5.198,3.271 5.521,3.521 0.323,0.25 10 7 6.479,4.75 6.938,4.99 0.458,0.24 10 ECM 6.49,4.563 6.948,4.802 0.458,0.24 10 A62 2.031,4.552 2.833,4.875 0.802,0.323 10 No. 1 Switch Wire 3.073,4.563 4.083,5.073 1.01,0.51 10 Steering Pad Switch Assembly 4.323,4.563 5.25,4.906 0.927,0.344 10 Spiral Cable Sub-assembly

CAUTION / NOTICE / HINT

CAUTION:

Refer to the SRS precaution before troubleshooting.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION


NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND)
a.
C277066C01
0.438,1 0.844,1.281 0.406,0.281 1.458,1.042 0.969,0.5 true 0.104,0.094 0.417,0.292 0.313,0.198 10 *a 0.615,0.417 1.083,0.635 0.469,0.219 10 ECC 0.542,1.052 0.854,1.25 0.313,0.198 10 G8
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-2 (ECC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL

C279692C02
0.583,1.479 0.927,1.729 0.344,0.25 4.719,1.229 5.063,1.479 0.344,0.25 1.729,2.25 1.479,1.906 true 0.979,2.271 1.281,1.906 true 1.271,1.385 0.979,0.927 true 5.281,1.271 5.104,0.792 true 5.281,1.51 5.125,1.979 true 5.833,1.5 5.99,1.979 true 0.146,0.115 0.458,0.313 0.313,0.198 10 *1 1.802,2.208 2.188,2.458 0.385,0.25 10 SUP 4.75,0.729 5.208,0.927 0.458,0.198 10 SUP 0.604,2.198 1.063,2.396 0.458,0.198 10 SDN 4.76,1.917 5.219,2.115 0.458,0.198 10 SDN 0.604,0.844 1.063,1.042 0.458,0.198 10 ECC 6.073,1.917 6.448,2.146 0.375,0.229 10 ECC 0.667,1.521 1,1.74 0.333,0.219 10 G8 4.823,1.271 5.281,1.469 0.458,0.198 10 z1
*1 Spiral Cable Sub-assembly - -



b.

Measure the resistance according to the value(s) in the table below.

i.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise and measure the resistance. Then rotate the spiral cable 2.5 times counterclockwise and measure the resistance.


ii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-14 (SUP) - z1-6 (SUP) Always Below 1 Ω
G8-7 (SDN) - z1-12 (SDN) Always Below 1 Ω
G8-2 (ECC) - z1-7 (ECC) Always Below 1 Ω
G8-14 (SUP) or z1-6 (SUP) - All other terminals Always 10 kΩ or higher
G8-7 (SDN) or z1-12 (SDN) - All other terminals Always 10 kΩ or higher
G8-2 (ECC) or z1-7 (ECC) - All other terminals Always 10 kΩ or higher


NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.




Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (LH)

NG

3.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (LH)
a.
C279489C02
3.021,1.49 2.76,1.042 true 2.625,1.49 2.625,1.042 true 2.188,1.5 2.51,1.052 true 2.917,1.563 3.365,1.792 0.448,0.229 10 SFTD 2.49,1.563 2.938,1.76 0.448,0.198 10 ECC 1.958,1.563 2.406,1.76 0.448,0.198 10 ECC1 0.104,0.083 0.417,0.281 0.313,0.198 10 *1
*1 Transmission Shift Switch Assembly (LH)


Remove the transmission shift switch assembly (LH).

Click hereDrivetrain>K111F MULTIDRIVE / CVT>SHIFT PADDLE SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
SFTD - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTD - ECC1 "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTD - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
SFTD - ECC1 "-" shift paddle not operated (down-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (RH)

NG

REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY (LH)

4.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (RH)
a.
C279490C02
2.292,1.354 2.448,0.833 true 2.771,1.344 2.573,0.833 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *1 2.052,1.438 2.51,1.667 0.458,0.229 10 SFTU 2.708,1.438 3.198,1.688 0.49,0.25 10 ECC1
*1 Transmission Shift Switch Assembly (RH)


Remove the transmission shift switch assembly (RH).

Click hereDrivetrain>K111F MULTIDRIVE / CVT>SHIFT PADDLE SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
SFTU - ECC1 "+" shift paddle operated and held (up-shift) Below 2.5 Ω
SFTU - ECC1 "+" shift paddle not operated (up-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 SWITCH WIRE

NG

REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY (RH)

5.INSPECT NO. 1 SWITCH WIRE
a.
C279491C02
1.781,1.135 2.385,0.896 true 1.792,1.333 2.365,1.573 true 1.635,1.135 0.99,0.896 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.573,0.813 1.188,1.01 0.615,0.198 10 false SFTU 2.469,0.813 3.083,1.01 0.615,0.198 10 false SFTD 2.458,1.51 3.073,1.708 0.615,0.198 10 false ECC
*a No. 1 Switch Wire (Steering Pad Switch Side)


Disconnect the No. 1 switch wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
SFTD - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTU - ECC "+" shift paddle operated and held (up-shift) Below 2.5 Ω
SFTD - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
SFTU - ECC "+" shift paddle not operated (up-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

6.INSPECT STEERING PAD SWITCH ASSEMBLY
a.
C200879C03
0.396,0.958 0.833,1.219 0.438,0.26 2.073,1.083 2.448,0.677 true 2.094,1.385 2.438,1.781 true 1.344,1.385 1.031,1.802 true 0.573,1.01 0.948,1.24 0.375,0.229 10 false z1 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.656,1.719 1.073,1.917 0.417,0.198 10 false ECC 2.521,0.583 2.938,0.781 0.417,0.198 10 false SUP 2.51,1.719 2.927,1.917 0.417,0.198 10 false SDN
*a Steering Pad Switch Assembly Connector (to Spiral Cable Sub-assembly)


Disconnect the steering pad switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
z1-6 (SUP) - z1-7 (ECC) "+" shift paddle operated and held (up-shift) Below 2.5 Ω
z1-12 (SDN) - z1-7 (ECC) "-" shift paddle operated and held (down-shift) Below 2.5 Ω
z1-6 (SUP) - z1-7 (ECC) "+" shift paddle not operated (up-shift) 1 MΩ or higher
z1-12 (SDN) - z1-7 (ECC) "-" shift paddle not operated (down-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)
a.
C277060C03
1.531,0.167 1.896,0.427 0.365,0.26 2.677,1.833 2.313,1.167 true 1.906,1.813 2.229,1.167 true 0.083,0.052 0.396,0.25 0.313,0.198 10 *a 1.604,0.208 1.917,0.406 0.313,0.198 10 A62 1.5,1.906 2.219,2.125 0.719,0.219 10 42 (SFTU) 2.458,1.906 3.167,2.115 0.708,0.208 10 43 (SFTD)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A62-42 (SFTU) - Body ground "+" shift paddle operated and held (up-shift) Below 2.5 Ω
A62-43 (SFTD) - Body ground "-" shift paddle operated and held (down-shift) Below 2.5 Ω
A62-42 (SFTU) - Body ground "+" shift paddle not operated (up-shift) 1 MΩ or higher
A62-43 (SFTD) - Body ground "-" shift paddle not operated (down-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT