Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Pattern Select Switch Sport Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and sport shift patterns.

By following the programs corresponding to the signals from the combination switch, the park/neutral position switch and other various sensors, the ECM switches the shift control solenoid valves on and off, and controls the transaxle gear ratio.

WIRING DIAGRAM

C278992E02
5.813,3.219 6.281,3.438 0.469,0.219 10 ECM 5.823,3.021 6.281,3.219 0.458,0.198 10 A62 5.604,1.385 6.271,1.646 0.667,0.26 10 PWMS 5.333,1.5 5.594,1.719 0.26,0.219 10 57 2.563,2.021 3.01,2.25 0.448,0.229 10 G60 2.563,2.219 3.927,2.5 1.365,0.281 10 Combination Switch 3.396,1.25 4.021,1.479 0.625,0.229 10 MSW1 2.531,1.24 3.167,1.458 0.635,0.219 10 MSW2 3.917,1.5 4.073,1.698 0.156,0.198 10 2 2.333,1.51 2.49,1.708 0.156,0.198 10 4

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT COMBINATION SWITCH ASSEMBLY
a.
C277027C02
1.354,1.792 1.51,1.385 true 2.042,1.771 1.875,1.385 true 1.094,1.844 1.708,2.073 0.615,0.229 10 false MSW2 1.896,1.844 2.51,2.063 0.615,0.219 10 false MSW1 0.104,0.104 0.719,0.302 0.615,0.198 10 false *1
*1 Combination Switch Assembly


Remove the combination switch.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>COMBINATION SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (MSW1) - 4 (MSW2) Combination switch (SPORT) on Below 1 Ω
2 (MSW1) - 4 (MSW2) Combination switch (SPORT) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - BODY GROUND)

NG

REPLACE COMBINATION SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - BODY GROUND)
a.
C277026C02
0.458,0.948 0.854,1.198 0.396,0.25 2.125,1.74 1.927,1.323 true 0.104,0.083 0.417,0.281 0.313,0.198 10 *a 1.948,1.813 2.5,2.031 0.552,0.219 10 MSW2 0.531,0.979 0.865,1.156 0.333,0.177 10 G60
*a Front view of wire harness connector
(to Combination Switch Assembly)


Disconnect the combination switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G60-4 (MSW2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - ECM)
a.
C277060C01
1.531,0.167 1.896,0.427 0.365,0.26 2.479,1.823 2.229,1.25 true 0.083,0.052 0.396,0.25 0.313,0.198 10 *a 1.604,0.208 1.917,0.406 0.313,0.198 10 A62 2.167,1.906 2.99,2.115 0.823,0.208 10 57 (PWMS)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A62-57 (PWMS) - Body ground Combination switch (SPORT) on Below 1 Ω
A62-57 (PWMS) - Body ground Combination switch (SPORT) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT