Home › Power Source / Network › 2AD-FTV BATTERY / CHARGING › CHARGING SYSTEM
RM3090E _57 Power Source / Network _008780 2AD-FTV BATTERY / CHARGING _0051075 CHARGING SYSTEM C

2AD-FTV BATTERY / CHARGING  CHARGING SYSTEM  P1602  Deterioration of Battery  


DESCRIPTION

The ECM monitors the battery. When the engine is running (not cranking) and the battery voltage drops below a specified level, the ECM determines that there is battery deterioration and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1602 Deterioration of Battery Battery voltage is 11.85 V or less for 10 seconds or more when the engine is running (60 seconds elapses after the engine is started)
(1 trip detection logic)
·

Battery

·

Wire harness or connector

·

EFI-MAIN NO. 1 fuse

·

EFI NO. 3 fuse


Does not come on DTC stored

WIRING DIAGRAM

A298733E02
5.708,2.083 6.167,2.281 0.458,0.198 10 false ECM 5.083,1.281 5.542,1.479 0.458,0.198 10 false B76 5.083,0.396 5.542,0.594 0.458,0.198 10 false A61 3.802,0.573 4.573,0.823 0.771,0.25 10 false EFI NO. 3 1.802,0.604 2.917,0.833 1.115,0.229 10 false EFI-MAIN NO. 1 0.323,0.375 1.177,0.656 0.854,0.281 10 false from Battery 5.448,1.281 5.906,1.479 0.458,0.198 10 false E1 5.156,0.156 5.385,0.375 0.229,0.219 10 false 2 5.094,1.052 5.417,1.25 0.323,0.198 10 false 109 5.469,0.406 5.927,0.604 0.458,0.198 10 false BATT

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1602)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Proceed to
DTC P1602 is output
DTC P1602 and other DTCs are output


HINT:

If any DTCs other than P1602 are output, troubleshoot those DTCs first.




DTC P1602 is output

2.INSPECT CHARGING SYSTEM

DTC P1602 and other DTCs are output

2.INSPECT CHARGING SYSTEM

Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATT POWER SOURCE)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (BATT POWER SOURCE)
a.
A299850C01
0.302,0.927 0.729,1.24 0.427,0.313 1.604,0.844 1.438,0.427 1.438,0.427 1.229,0.438 true 0.375,0.99 0.813,1.24 0.438,0.25 10 A61 0.656,0.354 1.885,0.552 1.229,0.198 10 2 (BATT) 0.063,0.063 0.375,0.26 0.313,0.198 10 *a
*a Front view of wire harness connector
(to ECM)


Disconnect the A61 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A61-2 (BATT) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR