When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the EFI-MAIN NO. 1 relay, closing the contacts and supplying power to terminals +B and +B2 of the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | IG2 Relay |
Remove the IG2 relay from the engine room relay block and junction block assembly.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 1 - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Entry and Start System) | B |
| NG (w/ Entry and Start System) | C |
A
B
C
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | IG2 Relay |
Remove the IG2 relay from the engine room relay block and junction block assembly.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI-MAIN NO. 1 Relay |
Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 3 - Body ground | Always | 11 to 14 V |
| EFI-MAIN NO. 1 relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the IG2 relay.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
Inspect the EFI-MAIN NO. 1 relay.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay from the engine room relay block and junction block assembly.
Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 2 - Body ground | Always | Below 1 Ω |
| EFI-MAIN NO. 1 relay terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay from the engine room relay block and junction block assembly.
Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 5 - A62-37 (IGSW) | Always | Below 1 Ω |
| EFI-MAIN NO. 1 relay terminal 3 - A62-2 (+B) | Always | Below 1 Ω |
| EFI-MAIN NO. 1 relay terminal 3 - A62-3 (+B2) | Always | Below 1 Ω |
| EFI-MAIN NO. 1 relay terminal 1 - A62-46 (MREL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B77-16 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-4 (AM2) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay from the engine room relay block and junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-9 (IG2D) - IG2 relay terminal 1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG