Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2012.12–2014.10
RM3090E _52 Drivetrain _008753 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0051089 AUTOMATIC TRANSAXLE UNIT A

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Check bearing position and installation direction.

C319493N01
0.625,3.458 0.802,3.688 0.177,0.229 10 false A 2.479,4.229 2.656,4.458 0.177,0.229 10 false B 3.688,5.438 3.865,5.667 0.177,0.229 10 false C 5.76,6.531 5.938,6.76 0.177,0.229 10 false D

C238855N01
2.26,5.884 2.433,6.057 0.173,0.173 10 E 4.61,6.585 4.783,6.758 0.173,0.173 10 H 1.085,8.489 1.258,8.662 0.173,0.173 10 F 2.29,8.79 2.463,8.963 0.173,0.173 10 G

Mark Front Race Diameter
Inside / Outside
Thrust Bearing Diameter
Inside / Outside
Rear Race Diameter
Inside / Outside
A - 57.7 mm (2.27 in.) / 75.2 mm (2.96 in.) -
B - 29.1 mm (1.15 in.) / 48.6 mm (1.91 in.) 30.7 mm (1.21 in.) / 48.3 mm (1.90 in.)
C - 62.6 mm (2.46 in.) / 82.4 mm (3.24 in.) 65.9 mm (2.59 in.) / 82.3 mm (3.24 in.)
D 59.4 mm (2.34 in.) / 76 mm (2.99 in.) 53.46 mm (2.10 in.) / 79 mm (3.11 in.) -
E - 56.1 mm (2.21 in.) / 81.1 mm (3.19 in.) -
F - 61.2 mm (2.41 in.) / 79 mm (3.11 in.) -
G - 28 mm (1.10 in.) / 47.1 mm (1.85 in.) 26.1 mm (1.03 in.) / 44 mm (1.73 in.)
H 52.2 mm (2.06 in.) / 70.4 mm (2.77 in.) 48.9 mm (1.93 in.) / 72.0 mm (2.83 in.) -


PROCEDURE

Hide 35782E 1.INSTALL COUNTER DRIVE GEAR BEARING

HINT:

Perform this procedure only when the counter drive gear bearing or transaxle case is replaced.


a.
C138721N07
1.594,1.01 2.375,0.906 2.375,0.906 1.76,1.188 true 1.625,2.115 0.833,2.656 0.833,2.656 1.646,2.469 true 2.417,0.813 2.76,0.979 0.344,0.167 10 SST 0.427,2.573 0.771,2.74 0.344,0.167 10 SST

Using SST and a press, install a new counter drive gear bearing and snap ring to the transaxle case sub-assembly.

SST
09950-60020  (09951-01030)
09950-70010  (09951-07100)


Hide 2.INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

a.
C137443N03
1.406,1.073 0.667,0.333 0.667,0.333 1.302,1.219 true 0.354,0.24 0.833,0.427 0.479,0.188 10 SST

Using SST and a hammer, install a new counter driven gear rear tapered roller bearing outer race to the transaxle case.

SST
09950-60010  (09951-00630)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the counter driven gear rear tapered roller bearing outer race so that there is no clearance between the bearing outer race and the transaxle case. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



Hide 41311F 3.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING OUTER RACE

a.
C138714N04
1.396,1.104 0.5,0.344 0.5,0.344 1.188,1.24 true 0.167,0.25 0.49,0.417 0.323,0.167 10 SST

Using SST and a hammer, tap in a new front differential case rear tapered roller bearing outer race to the transaxle case.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle case.



Hide 4.INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

a.

Install the shim to the transaxle housing.


b.
C138261N05
1.74,1.01 2.854,1.677 2.854,1.677 1.865,1.344 true 2.896,1.594 3.219,1.76 0.323,0.167 10 SST

Using SST, install a new counter driven gear front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the counter driven gear front tapered roller bearing outer race so that there is no clearance between the shim and the transaxle housing.



Hide 41311E 5.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING OUTER RACE

a.

Install the shim to the transaxle housing.


b.
C138715N05
1.854,1.104 2.625,1.521 2.625,1.521 1.948,1.438 true 2.698,1.448 3,1.615 0.302,0.167 10 SST

Using SST and a hammer, tap in a new front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle housing.



Hide 41311F 6.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING INNER RACE

a.
C333247N01
0.729,0.865 0.51,0.479 0.51,0.479 0.865,0.479 false 0.51,0.479 0.76,0.646 false 0.198,0.406 0.656,0.604 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing inner race to the front differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case rear tapered roller bearing inner race cage when installing the front differential case rear tapered roller bearing inner race.

·

Ensure that there is no clearance between the front differential case rear tapered roller bearing inner race and front differential case.




Hide 41311E 7.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING INNER RACE

a.
C333245N01
0.865,0.708 0.531,0.281 0.531,0.281 0.979,0.281 false 0.542,0.281 0.875,0.458 false 0.229,0.198 0.688,0.396 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing inner race to the front differential case.

SST
09523-36010  
09950-60010  (09951-00540)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case front tapered roller bearing inner race cage when installing the front differential case front tapered roller bearing inner race.

·

Ensure that there is no clearance between the front differential case front tapered roller bearing inner race and front differential case.




Hide 8.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove packing material from the contact surfaces between the transaxle housing and transaxle case.


b.
C209724

Install the front differential case to the transaxle case.


c.
C280470N01
0.344,1.625 0.5,1.823 0.156,0.198 10 B 1.417,1.813 1.573,2.01 0.156,0.198 10 A 1.76,1.865 1.917,2.063 0.156,0.198 10 A 2.073,1.896 2.229,2.094 0.156,0.198 10 A 2.656,1.552 2.813,1.75 0.156,0.198 10 B 2.833,1.115 2.99,1.313 0.156,0.198 10 B 2.781,0.781 2.938,0.979 0.156,0.198 10 B 2.229,0.365 2.385,0.563 0.156,0.198 10 B 1.979,0.219 2.135,0.417 0.156,0.198 10 B 1.771,0.094 1.927,0.292 0.156,0.198 10 B 1.396,0.01 1.552,0.208 0.156,0.198 10 B 1.083,0.104 1.24,0.302 0.156,0.198 10 B 0.844,0.229 1,0.427 0.156,0.198 10 B 0.615,0.385 0.771,0.583 0.156,0.198 10 B 0.25,0.708 0.406,0.906 0.156,0.198 10 B 0.167,1.031 0.323,1.229 0.156,0.198 10 B 0.167,1.229 0.323,1.427 0.156,0.198 10 B 0.635,1.875 0.792,2.073 0.156,0.198 10 B 1.01,1.969 1.167,2.167 0.156,0.198 10 B 1.198,1.948 1.354,2.146 0.156,0.198 10 B

Install the transaxle housing to the transaxle case with the 20 bolts.

Torque:
for Bolt A : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)
for Bolt B : 30.6 N*m (312 kgf*cm, 23 ft.*lbf)


d.
C314367N01
1.333,4.281 1.052,4.281 1.052,4.281 1.052,3.156 true 1.385,4.177 1.927,4.448 0.542,0.271 10 false SST

Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.

SST
09564-33010  

Turning torque:

1.23 to 1.65 N*m (12.55 to 16.82 kgf*cm, 10.89 to 14.60 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness:
Thickness Thickness Thickness Thickness
2.000 mm (0.0787 in.) 2.225 mm (0.0876 in.) 2.450 mm (0.0965 in.) 2.675 mm (0.105 in.)
2.025 mm (0.0797 in.) 2.250 mm (0.0886 in.) 2.475 mm (0.0974 in.) 2.700 mm (0.106 in.)
2.050 mm (0.0807 in.) 2.275 mm (0.0896 in.) 2.500 mm (0.0984 in.) 2.725 mm (0.107 in.)
2.075 mm (0.0817 in.) 2.300 mm (0.0906 in.) 2.525 mm (0.0994 in.) 2.750 mm (0.108 in.)
2.100 mm (0.0827 in.) 2.325 mm (0.0915 in.) 2.550 mm (0.100 in.) 2.775 mm (0.109 in.)
2.125 mm (0.0837 in.) 2.350 mm (0.0925 in.) 2.575 mm (0.101 in.) 2.800 mm (0.110 in.)
2.150 mm (0.0846 in.) 2.375 mm (0.0935 in.) 2.600 mm (0.102 in.) 2.825 mm (0.111 in.)
2.175 mm (0.0856 in.) 2.400 mm (0.0945 in.) 2.625 mm (0.103 in.) 2.850 mm (0.112 in.)
2.200 mm (0.0866 in.) 2.425 mm (0.0955 in.) 2.650 mm (0.104 in.) 2.875 mm (0.113 in.)


e.
C205233

Remove the 20 bolts and the transaxle housing from the transaxle case.


f.

Remove the front differential case from the transaxle case.


Hide 9.INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

a.
C138250N05
2.469,0.76 1.833,1.021 false 2.521,0.667 2.885,0.844 0.365,0.177 10 SST

Using SST and a press, install a new counter driven gear front tapered roller bearing to the counter driven gear.

SST
09950-60010  (09951-00490)

NOTICE:

Be sure to install the counter driven gear front tapered roller bearing so that there is no clearance between the bearing and the counter driven gear. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



Hide 10.INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

a.
C138251N05
1.875,1.104 2.375,0.792 false 2.417,0.708 2.76,0.875 0.344,0.167 10 SST

Using SST and a press, install a new counter driven gear rear tapered roller bearing to the counter driven gear.

SST
09950-60010  (09951-00400)

NOTICE:

Be sure to install the counter driven gear rear tapered roller bearing so that there is no clearance between each of them and the counter driven gear.



Hide 11.ADJUST COUNTER DRIVEN GEAR PRELOAD

a.
C209725

Install the counter driven gear and front differential case to the transaxle case.


b.
C280470N01
0.344,1.625 0.5,1.823 0.156,0.198 10 B 1.417,1.813 1.573,2.01 0.156,0.198 10 A 1.76,1.865 1.917,2.063 0.156,0.198 10 A 2.073,1.896 2.229,2.094 0.156,0.198 10 A 2.656,1.552 2.813,1.75 0.156,0.198 10 B 2.833,1.115 2.99,1.313 0.156,0.198 10 B 2.781,0.781 2.938,0.979 0.156,0.198 10 B 2.229,0.365 2.385,0.563 0.156,0.198 10 B 1.979,0.219 2.135,0.417 0.156,0.198 10 B 1.771,0.094 1.927,0.292 0.156,0.198 10 B 1.396,0.01 1.552,0.208 0.156,0.198 10 B 1.083,0.104 1.24,0.302 0.156,0.198 10 B 0.844,0.229 1,0.427 0.156,0.198 10 B 0.615,0.385 0.771,0.583 0.156,0.198 10 B 0.25,0.708 0.406,0.906 0.156,0.198 10 B 0.167,1.031 0.323,1.229 0.156,0.198 10 B 0.167,1.229 0.323,1.427 0.156,0.198 10 B 0.635,1.875 0.792,2.073 0.156,0.198 10 B 1.01,1.969 1.167,2.167 0.156,0.198 10 B 1.198,1.948 1.354,2.146 0.156,0.198 10 B

Install the transaxle housing to the transaxle case with the 20 bolts.

Torque:
for Bolt A : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)
for Bolt B : 30.6 N*m (312 kgf*cm, 23 ft.*lbf)


c.
C317726N01
1.25,4.354 1.021,4.354 1.021,4.354 1.021,3.406 false 1.313,4.281 1.802,4.531 0.49,0.25 10 false SST

Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

SST
09564-33010  

Turning torque:

Differential side bearing preload + 2.96 to 6.54 N*m (30.19 to 66.68 kgf*cm, 26.20 to 57.88 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim of the counter driven gear front tapered roller bearing outer race so that the turning torque is within the specified range.

Shim Thickness:
Thickness Thickness Thickness Thickness
2.000 mm (0.0787 in.) 2.275 mm (0.0896 in.) 2.525 mm (0.0994 in.) 2.775 mm (0.109 in.)
2.025 mm (0.0797 in.) 2.300 mm (0.0906 in.) 2.550 mm (0.100 in.) 2.800 mm (0.110 in.)
2.050 mm (0.0807 in.) 2.325 mm (0.0915 in.) 2.575 mm (0.101 in.) 2.825 mm (0.111 in.)
2.075 mm (0.0817 in.) 2.350 mm (0.0925 in.) 2.600 mm (0.102 in.) 2.850 mm (0.112 in.)
2.100 mm (0.0827 in.) 2.375 mm (0.0935 in.) 2.625 mm (0.103 in.) 2.875 mm (0.113 in.)
2.125 mm (0.0837 in.) 2.400 mm (0.0945 in.) 2.650 mm (0.104 in.) 2.900 mm (0.114 in.)
2.150 mm (0.0846 in.) 2.425 mm (0.0955 in.) 2.675 mm (0.105 in.) 2.925 mm (0.115 in.)
2.175 mm (0.0856 in.) 2.450 mm (0.0965 in.) 2.700 mm (0.106 in.) 2.950 mm (0.116 in.)
2.200 mm (0.0866 in.) 2.475 mm (0.0974 in.) 2.725 mm (0.107 in.) 2.975 mm (0.117 in.)
2.225 mm (0.0876 in.) 2.500 mm (0.0984 in.) 2.750 mm (0.108 in.) 3.000 mm (0.118 in.)
2.250 mm (0.0886 in.) - - -


d.
C205233

Remove the 20 bolts and the transaxle housing from the transaxle case.


e.

Remove the counter driven gear and front differential case from the transaxle case.


Hide 31105H 12.INSTALL TRANSAXLE CASE OIL SEAL LH

a.

Coat the lip of a new transaxle case oil seal LH with MP grease.


b.
C205332N05
1.448,1.26 0.552,2.427 0.552,2.427 1.417,1.552 true 1.958,1.896 2.875,1.542 2.875,1.542 2.417,1.927 true 0.26,2.365 0.583,2.521 0.323,0.156 10 SST 2.906,1.427 3.229,1.583 0.323,0.156 10 SST

Using SST and a hammer, tap in a new transaxle case oil seal LH.

SST
09316-10010  09950-70010  (09951-07100)

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Make sure that the transaxle oil seal LH is installed in the correct direction.



Hide 31105H 13.INSTALL TRANSAXLE CASE OIL SEAL RH (OUTER)

a.

Coat the lip of a new transaxle case oil seal RH (outer) with MP grease.


b.
C205241N01
0.813,0.76 0.385,1 0.385,1 0.667,1.01 true 2.365,0.292 2.198,0.167 2.198,0.167 2.281,0.5 true 0.042,0.906 0.333,1.063 0.292,0.156 10 SST 1.854,0.083 2.146,0.24 0.292,0.156 10 SST

Using SST and a hammer, tap in the transaxle case oil seal RH (outer).

SST
09649-17010  09950-70010  (09951-07200)

Standard depth:

5.5 to 6.5 mm (0.217 to 0.255 in.)


NOTICE:

Make sure that the transaxle case oil seal RH is installed in the correct direction.



Hide 35506F 14.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C188148N02
1.24,1.969 0.969,1.969 0.969,1.969 1.219,2.25 false 1.635,1.365 0.646,0.396 0.646,0.396 1.635,1.177 true 0.677,1.906 0.99,2.063 0.313,0.156 10 SST 0.344,0.323 0.656,0.479 0.313,0.156 10 SST

Coat the lip of a new manual valve lever shaft oil seal with a small amount of MP grease.


b.

Using SST and a hammer, tap in the manual valve lever shaft oil seal.

SST
09950-60010  (09951-00230)
09950-70010  (09951-07100)

Oil seal tap in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the manual valve lever shaft oil seal is installed in the correct direction.



Hide 35506 15.INSTALL MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201357

Install the manual valve lever shaft sub-assembly to the transaxle case.

NOTICE:

Do not damage the manual valve lever shaft oil seal while installing the manual valve lever shaft sub-assembly to the transaxle case.



b.
C201356

Using needle-nose pliers, install the manual valve shaft retainer spring to the transaxle case.


Hide 35501 16.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C201355

Align the slot with the notches on the manual valve lever shaft sub-assembly and install the parking lock rod sub-assembly.


Hide 35409 17.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Install the manual detent spring sub-assembly and manual detent spring cover to the transaxle case with the bolt.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)

NOTICE:

Make sure to install the manual detent spring sub-assembly first and then the manual detent spring cover.



Hide 35623 18.INSTALL NO. 3 BRAKE PISTON

a.
C317138

Coat 2 new O-rings with ATF and install them to the No. 3 brake piston.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.
C317912C01
1.656,0.677 1.313,0.135 1.313,0.135 1.146,0.135 true 0.938,0.063 1.25,0.292 0.313,0.229 10 false *1
*1 No. 3 Brake Piston


Temporarily install the No. 3 brake piston to the transaxle.


c.
C317914C01
0.594,0.219 0.74,0.219 0.74,0.219 0.906,0.385 false 0.688,1.521 0.833,1.521 0.833,1.521 1,1.177 false 0.417,0.146 0.75,0.323 0.333,0.177 10 false *1 0.51,1.438 0.885,1.729 0.375,0.292 10 false *2
*1 No. 3 Brake Piston
*2 Pawl Stopper Plate


Temporarily install the pawl stopper plate to the transaxle case with the 2 bolts.

NOTICE:

After installing, make sure that the protrusions on the No. 3 brake piston and the grooves on the pawl stopper plate are aligned.



d.

Press the No. 3 brake piston into the transaxle case.

NOTICE:

Make sure that the lip of the No. 3 brake piston is not twisted and does not get caught in the transaxle case.


HINT:

Use the installation surface of the return spring to press the piston into the transaxle case.



e.

Remove the 2 bolts and pawl stopper plate from the transaxle case.


f.
C317915C01
1.083,1.188 0.948,1.188 0.948,1.188 0.75,0.479 true 1.25,1.01 1.167,1.01 1.167,1.01 0.76,0.323 true 1.313,0.917 1.625,1.167 0.313,0.25 10 false *1 1.135,1.104 1.448,1.26 0.313,0.156 10 false *2
*1 No. 3 Brake Piston
*2 Brake Piston Return Spring


Install the brake piston return spring to the transaxle case.

NOTICE:

Install the brake piston return spring as shown in the illustration.



g.

Place SST on the brake piston return spring and compress the brake piston return spring with a press.

C317916C01
1,0.5 1.135,0.5 1.135,0.5 1.792,1.552 true 2.188,1.854 2.469,2.573 2.469,2.573 2.625,2.573 true 4.583,0.365 4.75,0.365 4.75,0.365 5.281,1.24 true 4.406,0.292 4.823,0.583 0.417,0.292 10 false *1 0.698,0.427 1.135,0.74 0.438,0.313 10 false SST 2.698,2.49 3.031,2.729 0.333,0.24 10 false *a
*1 Snap Ring - -
*a Protective Tape - -


SST
09387-00070  

NOTICE:

Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



h.

Using a screwdriver, install the snap ring to the transaxle case as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case.

·

Be sure to align the opening of the snap ring with one of the protrusions on the brake piston return spring as shown in the illustration.

·

Be careful not to damage the transaxle case.



HINT:

Tape the screwdriver tip before use.



Hide 35782C 19.INSTALL COUNTER DRIVE GEAR

a.
C137423N01
2.173,0.718 2.491,0.879 0.318,0.161 10 SST 2.133,0.787 1.876,0.896 false

Using SST and a press, install a new counter drive gear bearing inner race (front side) to the counter drive gear.

SST
09387-00020  


b.
C274849N02
1.667,3.76 2.104,3.938 2.104,3.938 1.698,3.938 true 1.156,2.656 1.469,2.656 1.469,2.656 1.302,3.052 true 1.5,2.594 1.958,2.792 0.458,0.198 10 SST 2.156,3.885 2.615,4.083 0.458,0.198 10 SST

Using SST, install a new counter drive gear bearing inner race (rear side) and counter drive gear to the transaxle case.

SST
09223-15030  
09527-17011  
09950-60020  (09951-00810)
09950-70010  (09951-07100)

NOTICE:

There should not be any clearance between the counter drive gear bearing inner race (front side) and counter drive gear.



Hide 35720 20.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C274850N02
1.906,0.792 2.323,0.375 true 1.844,2.563 2.052,2.563 true 1.844,3.979 2.052,3.979 2.052,3.979 1.823,3.75 true 2.365,0.302 2.823,0.5 0.458,0.198 10 SST 2.094,2.5 2.552,2.698 0.458,0.198 10 SST 2.094,3.927 2.552,4.125 0.458,0.198 10 SST

Using SST and a press, press in a new front planetary gear assembly to the transaxle case.

SST
09223-15030  
09527-17011  
09951-01100  


Hide 35622G 21.INSTALL NO. 2 BRAKE PISTON

a.
C201346

Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.
C138726

Install the No. 2 brake piston to the transaxle case.

NOTICE:

Be careful not to damage the O-rings.



Hide 35068C 22.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.

Install the 1st and reverse brake return spring sub-assembly to the transaxle case.

C281638C01
1.177,0.229 1.323,0.229 1.323,0.229 1.594,0.885 true 2.656,2.292 2.854,2.292 false 3.073,0.625 2.917,0.625 2.917,0.625 2.438,1.073 true 3.125,0.531 3.396,0.729 0.271,0.198 10 false *a 0.875,0.156 1.229,0.354 0.354,0.198 10 false SST 2.917,2.208 3.271,2.406 0.354,0.198 10 false SST
*a Protective Tape - -



b.

Place SST on the 1st and reverse brake return spring assembly and compress the 1st and reverse brake return spring sub-assembly with a press.

SST
09387-00060  

NOTICE:

Stop the press when the 1st and reverse brake return spring sub-assembly is flush with the snap ring groove. This prevents the 1st and reverse brake return spring sub-assembly from being deformed.



c.

Using a screwdriver, install the snap ring to the transaxle case as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.

·

Be careful not to damage the transaxle case.



HINT:

Tape the screwdriver tip before use.



Hide 35682A 23.INSTALL NO. 2 BRAKE DISC

a.
C238853C01
1.333,0.969 1.177,0.969 1.177,0.969 1.177,1.75 false 1.177,1.75 1.333,1.75 false 1.323,1.229 1.177,1.229 false 1.323,1.479 1.177,1.479 false 1.177,1.354 1.063,1.354 false 2.177,0.552 2.323,0.552 false 2.208,0.802 2.375,0.802 2.375,0.802 2.375,1.573 false 2.375,1.573 2.208,1.573 false 2.208,1.063 2.375,1.063 false 2.208,1.323 2.375,1.323 false 2.375,1.188 2.458,1.188 false 2.5,1.115 2.667,1.292 0.167,0.177 10 *3 0.885,1.292 1.042,1.469 0.156,0.177 10 *2 2.365,0.479 2.531,0.656 0.167,0.177 10 *1
*1 No. 2 Brake Flange
*2 No. 2 Brake Plate
*3 No. 2 Brake Disc


Install the 4 No. 2 brake discs, 4 No. 2 brake plates, and No. 2 brake flange to the transaxle case.

NOTICE:

Make sure that the discs, plates, and flange are installed in the correct order.



b.
C281626C01
2.146,1.26 1.833,0.385 1.833,0.385 1.719,0.385 true 1.552,0.292 1.865,0.448 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the transaxle case.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.

·

Be careful not to damage the transaxle case.



HINT:

Tape the screwdriver tip before use.



Hide 35762E 25.INSTALL PLANETARY RING GEAR FLANGE

a.
C136480C01
1.26,0.646 0.958,0.646 false 0.938,2.292 1.198,2.292 false 2.125,1.375 2.438,1.375 false 0.771,2.177 0.948,2.344 0.177,0.167 10 *3 2.479,1.26 2.646,1.417 0.167,0.156 10 *2 0.802,0.531 0.979,0.698 0.177,0.167 10 *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Install the planetary ring gear flange to the planetary ring gear.


b.

Using a screwdriver, install the snap ring to the planetary ring gear.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the planetary ring gear.

·

Be careful not to damage the planetary ring gear.



HINT:

Tape the screwdriver tip before use.



Hide 35790 26.INSTALL ONE-WAY CLUTCH ASSEMBLY

a.
C201345C01
0.875,0.135 0.969,0.135 0.969,0.135 1.271,0.417 false 1.115,1.438 1.375,1.438 false 2.521,1 2.802,1.073 2.802,1.073 2.802,1.156 false 0.719,0.042 0.875,0.229 0.156,0.188 10 false *1 0.948,1.344 1.115,1.521 0.167,0.177 10 false *3 2.75,1.156 2.938,1.354 0.188,0.198 10 false *2
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


Install the outer race retainer to the one-way clutch assembly.


b.

Install the one-way clutch assembly to the planetary ring gear.

NOTICE:

Make sure that the one-way clutch assembly is positioned in the correct direction as shown in the illustration.



c.

Coat the thrust needle roller bearing with ATF, and install it onto the front planetary gear assembly.

C274852C02
1.698,1.479 2.49,2.531 2.49,2.531 2.708,2.531 true 2.771,2.49 3.083,2.688 0.313,0.198 10 *1
*1 Thrust Needle Roller Bearing - -


Bearing Diameter
- Inside Outside
Bearing 56.1 mm (2.21 in.) 81.1 mm (3.19 in.)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



d.

Install the one-way clutch assembly with the planetary ring gear to the transaxle case.

NOTICE:

Make sure that there is no clearance between the retainer and the claw on the one-way clutch assembly. If there is any clearance, the spring of the retainer will be deformed.



e.
C281622C01
2.24,1.24 2.073,0.458 2.073,0.458 1.938,0.458 true 1.771,0.365 2.083,0.521 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the transaxle case.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.

·

Be careful not to damage the transaxle case.



HINT:

Tape the screwdriver tip before use.



Hide 35557 27.INSTALL PARKING LOCK PAWL

a.
C201343C01
0.583,1.448 0.677,1.448 0.677,1.448 0.969,1.542 false 0.906,0.156 0.802,0.156 0.802,0.156 1.031,1.229 false 1.594,0.49 1.521,0.49 1.521,0.49 1.396,1.292 false 2.531,1.385 2.417,1.385 2.417,1.385 2.052,1.677 false 0.427,1.323 0.604,1.5 0.177,0.177 10 *3 0.927,0.042 1.125,0.198 0.198,0.156 10 *1 1.625,0.385 1.802,0.563 0.177,0.177 10 *2 2.563,1.26 2.719,1.427 0.156,0.167 10 *4
*1 Parking Lock Pawl Pin
*2 Parking Lock Pawl Shaft
*3 Spring
*4 Parking Lock Pawl


Install the parking lock pawl to the transaxle case with the parking lock pawl shaft.


b.

Install the parking lock pawl pin to the transaxle case.


c.
C137444

Install the spring to the parking lock pawl.

NOTICE:

Make sure that one end of the spring is secured in the hole of the transaxle case and the other end is positioned on the parking lock pawl as shown in the illustration.



Hide 35598 28.INSTALL PARKING LOCK SLEEVE

a.
C201342

Install the parking lock sleeve to the transaxle case.


Hide 35596 29.INSTALL PAWL STOPPER PLATE

a.
C201341

Install the pawl stopper plate to the transaxle case with the 2 bolts.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35165 30.INSTALL NO. 1 TRANSMISSION CASE PLATE

a.
C203287N02
2.073,0.656 2.188,0.823 0.115,0.167 10 A

Clean and degrease the bolt and the installation hole in the transaxle case.


b.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the No. 1 transmission case plate to the transaxle case with the bolt.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)

HINT:

Tighten the bolt while part A of the No. 1 transmission case plate contacts the transaxle case as shown in the illustration.



Hide 35558 31.INSTALL PAWL SHAFT CLAMP

a.
C201339

Install the pawl shaft clamp to the transaxle case with the bolt.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35783R 32.INSTALL COUNTER DRIVEN GEAR

a.
C201336

Install the counter driven gear to the transaxle case.


Hide 35782H 33.INSTALL COUNTER DRIVE GEAR NUT

a.
C201334N01
1.151,3.98 1.291,4.135 0.14,0.154 10 P

Turn the manual valve lever shaft counterclockwise to set it to the P position as shown in the illustration.


b.
C201527N02
0.927,0.281 1.031,0.281 1.031,0.281 1.823,0.99 false 0.615,0.198 0.948,0.375 0.333,0.177 10 SST

Using SST, install a new counter drive gear nut.

SST
09387-00130  

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


c.
C201335N01
1.487,4.004 1.625,4.186 0.137,0.182 10 N

Turn the manual valve lever shaft 2 notches clockwise to set it to the N position as shown in the illustration.


d.
C138252N01
1.563,1.813 0.656,2.167 false 0.323,2.104 0.646,2.292 0.323,0.188 10 SST

Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.

SST
09387-00130  

Turning torque:

0.1 to 0.8 N*m (1 to 8 kgf*cm, 0.9 to 7.1 in.*lbf)


If the measured value is not within the specified range, gradually tighten the counter drive gear nut until the turning torque falls within the specified range.

Maximum torque:

180 N*m (1835 kgf*cm, 133 ft.*lbf)



e.

Using a chisel and hammer, securely stake the counter drive gear nut.


Hide 41311 34.INSTALL FRONT DIFFERENTIAL CASE

a.
C205240

Install the front differential case to the transaxle case.


Hide 35621F 35.INSTALL NO. 1 BRAKE PISTON

a.
C274846

Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.
C138253

Install the No. 1 brake piston to the oil pump assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35608L 36.INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Install the 3 2nd brake piston return springs to the oil pump assembly.

NOTICE:

Make sure that the 3 2nd brake piston return springs are installed onto the protrusions on the oil pump assembly.



Hide 35681 37.INSTALL NO. 1 BRAKE DISC

a.
C201529C01
1.552,0.177 1.698,0.177 1.698,0.177 2,0.552 false 2.76,1.49 3,1.49 false 2.76,1.021 2.865,1.021 2.865,1.021 2.865,1.969 false 2.865,1.969 2.75,1.969 false 1.938,1.292 1.51,1.292 false 1.927,2.188 1.729,2.188 1.729,2.188 1.729,1.302 false 1.927,1.719 1.729,1.719 false 1.396,0.094 1.552,0.25 0.156,0.156 10 *1 1.365,1.198 1.542,1.396 0.177,0.198 10 *2 3.021,1.385 3.177,1.552 0.156,0.167 10 *3
*1 No. 1 Brake Flange
*2 No. 1 Brake Plate
*3 No. 1 Brake Disc


Install the 3 No. 1 brake discs, 3 No. 1 brake plates, and No. 1 brake flange to the oil pump assembly.

NOTICE:
·

Make sure that the discs, plates, and flange are installed in the correct order.

·

Be sure to install the flange in the correct direction.




b.
C281624C01
0.5,3.188 0.969,3.188 false 1.906,0.781 2.438,0.177 2.438,0.177 2.156,1.01 true 2.438,0.177 2.563,0.177 false 2.375,1.271 2.667,0.438 2.667,0.438 2.813,0.438 true 2.635,0.094 2.948,0.25 0.313,0.156 10 false SST 0.198,3.104 0.531,3.323 0.333,0.219 10 false (#1) 2.865,0.344 3.177,0.5 0.313,0.156 10 false *a
*a Protective Tape


Place SST on the flange and compress the flange with a press.

SST
09387-00070  
09495-65040  

NOTICE:

Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



c.

Using a screwdriver, install the snap ring to the oil pump assembly as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump assembly.

·

Make sure to align the protruding part of the snap ring with the indented part (#1) of the front oil pump and gear body assembly shown in the illustration to install the snap ring.

·

Be careful not to damage the oil pump assembly.



HINT:

Tape the screwdriver tip before use.



d.
C176220

Install the brake snap ring stopper to the oil pump assembly.

NOTICE:

Be sure to install the brake snap ring stopper in the correct direction.



e.
C201519N01
2.469,0.99 2.865,0.99 false 2.917,0.906 3.208,1.094 0.292,0.188 10 (#2)

Using a screwdriver, install the snap ring to the oil pump assembly as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump assembly.

·

Make sure to align the protruding part of the snap ring with the indented part (#2) of the oil pump assembly shown in the illustration to install the snap ring.

·

Be careful not to damage the oil pump assembly.



HINT:

Tape the screwdriver tip before use.



f.
C293925C02
1.25,2.5 1.417,2.5 1.417,2.5 1.667,2.198 false 1.5,1.708 1.917,0.5 1.917,0.5 2.083,0.5 true 1.75,1.708 1.917,0.5 true 1.083,2.417 1.396,2.573 0.313,0.156 10 false *1 2.104,0.417 2.417,0.573 0.313,0.156 10 false *2 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a
*1 Brake Snap Ring Stopper
*2 Snap Ring
*a Correctly Installed


Check that the brake snap ring stopper can be turned by hand.

NOTICE:

If the brake snap ring stopper cannot be turned by hand, the brake snap ring stopper may have been installed upside down, or the snap ring may not have been completely located in the groove on the oil pump assembly. Remove and reinstall the snap ring and the brake snap ring stopper.



Hide 35681 38.INSPECT CLEARANCE OF NO. 1 BRAKE DISC

Hide 34321 39.INSTALL UNDERDRIVE PLANETARY SUN GEAR

a.
C202904C01
2.313,1.396 2.229,1.396 2.229,1.396 2.01,1.313 false 0.979,0.49 1.406,0.49 false 0.833,0.396 1.01,0.573 0.177,0.177 10 *1 2.354,1.292 3.26,1.635 0.906,0.344 10 *2
*1 Underdrive Planetary Sun Gear
*2 Thrust Needle Roller Bearing


Coat the thrust needle roller bearing with ATF, and install it to the oil pump assembly.

Bearing Diameter
- Inside Outside
Bearing 57.7 mm (2.27 in.) 75.2 mm (2.96 in.)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.

Install the underdrive planetary sun gear to the oil pump assembly.


Hide 35701 40.INSTALL INPUT SHAFT SUB-ASSEMBLY

a.
C202905C01
1.156,1.01 1.344,1.01 false 0.938,2.208 1.479,2.208 false 1.719,2.802 2.333,2.479 2.333,2.479 1.74,3.135 false 1.74,2.979 2.333,2.479 false 1.115,0.188 1.25,0.188 1.25,0.188 1.427,0.365 false 0.969,0.094 1.125,0.271 0.156,0.177 10 *1 0.979,0.906 1.167,1.26 0.188,0.354 10 *2 0.771,2.115 0.938,2.302 0.167,0.188 10 *3 2.365,2.375 2.583,2.552 0.219,0.177 10 *4
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft Sub-assembly
*4 Oil Seal Ring


Coat 3 new oil seal rings with ATF and install them to the input shaft sub-assembly.

NOTICE:

Do not expand the gap of the oil seal ring too much.



b.

Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them on the input shaft sub-assembly.

Bearing and Race Diameter
- Inside Outside
Bearing 29.1 mm (1.15 in.) 48.6 mm (1.91 in.)
Race 30.7 mm (1.21 in.) 48.3 mm (1.90 in.)

NOTICE:

Be sure to install the thrust needle roller bearing in the correct direction.



c.
C136459

Install the input shaft sub-assembly to the oil pump assembly.


Hide 35706V 41.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C201331C01
1.271,0.302 1.385,0.302 1.385,0.302 1.646,0.854 false 1.552,3.031 1.26,3.031 false 2.438,1.396 2.333,1.396 2.333,1.396 1.979,2.146 false 1.115,0.219 1.281,0.385 0.167,0.167 10 false *1 1.104,2.948 1.292,3.115 0.188,0.167 10 false *3 2.469,1.313 2.667,1.49 0.198,0.177 10 false *2
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.


b.

Using a snap ring expander, install the planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.


Hide 34341 42.INSTALL UNDERDRIVE PLANETARY RING GEAR

HINT:

Perform this procedure only when replacement of the underdrive planetary ring gear or No. 3 brake hub is necessary.


a.
C290583

Install the snap ring to the underdrive planetary ring gear.


b.
C317256C02
2.698,1.438 2.552,1.438 2.552,1.438 2.344,1.01 false 2.76,1.344 3.104,1.688 0.344,0.344 10 false *a
*a Protective Tape


While compressing the snap ring with a screwdriver, install the underdrive planetary ring gear to the No. 3 brake hub.

NOTICE:

Confirm that the snap ring is correctly located in the groove of the No. 3 brake hub.


HINT:

tape the screwdriver tip before use.



Hide 35663 43.INSTALL NO. 3 BRAKE HUB

a.
C202906C01
1.146,0.208 1.271,0.208 1.271,0.208 1.469,0.344 false 1.188,1.115 1.271,1.115 1.271,1.115 1.469,0.948 false 1.01,0.125 1.188,0.292 0.177,0.167 10 false *1 1.031,1.052 1.271,1.365 0.24,0.313 10 false *2
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing


Coat the thrust needle roller bearing with ATF and install it on the underdrive planetary gear assembly.

Bearing and Race Diameter
- Inside Outside
Bearing 62.6 mm (2.47 in.) 82.4 mm (3.24 in.)
Race 65.9 mm (2.59 in.) 82.3 mm (3.24 in.)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.

Coat the thrust needle roller race with MP grease and install it to the No. 3 brake hub.


c.
C136454

Install the No. 3 brake hub to the underdrive planetary gear assembly.


Hide 34330 44.INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Install the underdrive planetary gear assembly to the oil pump assembly.


Hide 35683B 45.INSTALL NO. 3 BRAKE DISC

a.
C136452C01
2.125,0.458 2.313,0.458 false 2.156,1.24 2.302,1.24 false 2.156,0.771 2.229,0.771 2.229,0.771 2.229,1.688 false 2.229,1.688 2.156,1.688 false 1.188,1.99 1.333,1.99 false 1.313,1 1.125,1 false 1.313,1.51 1.229,1.51 1.229,1.51 1.229,1.01 false 2.344,0.365 2.51,0.552 0.167,0.188 10 *1 2.333,1.135 2.5,1.313 0.167,0.177 10 *3 0.969,0.896 1.146,1.073 0.177,0.177 10 *2 1.042,1.885 1.208,2.073 0.167,0.188 10 *1
*1 No. 3 Brake Flange
*2 No. 3 Brake Plate
*3 No. 3 Brake Disc


Install the 2 No. 3 brake flanges, 3 No. 3 brake discs, and 2 No. 3 brake plates to the oil pump assembly.

NOTICE:

Make sure that the discs, plates, and flanges are installed in the correct order.



b.
C274824N02
2.271,0.854 2.667,0.354 2.667,0.354 1.344,0.448 true 2.708,0.271 3.167,0.469 0.458,0.198 10 (A)

Using a screwdriver, install the snap ring to the oil pump assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump assembly.

·

Make sure that the snap ring ends are positioned as shown in the illustration (A).

·

Be careful not to damage the oil pump assembly.



HINT:

Tape the screwdriver tip before use.



Hide 35683B 46.INSPECT CLEARANCE OF NO. 3 BRAKE DISC

Hide 47.INSTALL OIL PUMP ASSEMBLY

a.
C293927C06
2.021,0.542 2.333,0.25 2.333,0.25 2.5,0.25 false 1.26,1.083 1,0.75 1,0.75 0.833,0.75 false 2.521,0.167 2.833,0.323 0.313,0.156 10 false *1 0.667,0.667 0.979,0.823 0.313,0.156 10 false *2
*1 Thrust Needle Roller Bearing
*2 O-ring


Coat a new O-ring with ATF and install it to the transaxle case.


b.

Coat the thrust needle roller bearing with ATF.


c.

Install the thrust needle roller bearing to the counter drive gear nut.

Thrust Needle Roller Bearing Diameter
- Inside Outside
Thrust needle roller bearing 53.46 mm (2.10 in.) 79 mm (3.11 in.)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race is visible.



d.

Coat the thrust needle roller race with MP grease.


e.
C293929C03
0.688,2.635 0.583,2.25 0.583,2.25 0.417,2.25 false 0.25,2.167 0.563,2.323 0.313,0.156 10 false *1
*1 Thrust Needle Roller Race


Install the thrust needle roller race to the underdrive planetary gear assembly.

Thrust Needle Roller Race Diameter
- Inside Outside
Thrust needle roller race 59.4 mm (2.34 in.) 76 mm (2.99 in.)


f.
C201329

Coat a new O-ring with ATF and install it to the oil pump assembly.


g.
C201328C01
0.781,0.198 0.594,0.198 false 0.448,0.125 0.604,0.313 0.156,0.188 10 *1
*1 O-ring


Install the oil pump assembly to the transaxle case with the 7 bolts.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


h.

Coat a new O-ring with ATF and install it to the oil pump assembly.


Hide 35174 48.INSTALL TRANSAXLE HOUSING OIL SEPARATOR

a.
C201327

Clean and degrease the 3 bolts and the installation holes in the transaxle housing.


b.

Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the transaxle housing oil separator to the transaxle housing with the 3 bolts.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35882A 49.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C201326

Install the differential gear lube apply tube to the transaxle housing.

NOTICE:

Insert the differential gear lube apply tube into the transaxle housing until it makes contact with the stopper.



b.

Clean and degrease the bolt and the installation hole in the transaxle housing.


c.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the apply tube clamp to the differential gear lube apply tube with the bolt.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)

NOTICE:

There should be clearance between the differential lube apply tube and apply tube clamp.



Hide 35111C 50.INSTALL TRANSAXLE HOUSING

a.
C201495

Clean and degrease the contact surfaces between the transaxle housing and transaxle case.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



b.

Apply seal packing to the transaxle case.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.

·

After applying seal packing, install the transaxle housing to the transaxle case within 3 minutes and tighten the bolts within 10 minutes.




c.
C205494

Install the transaxle housing to the transaxle case sub-assembly with the 17 bolts.

Torque:
30.6 N*m (312 kgf*cm, 23 ft.*lbf)


d.
C205495

Clean and degrease the 3 bolts and the installation holes in the transaxle case.


e.

Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.

Install the 3 bolts.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35730 52.INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

a.
C201526C01
2.125,0.885 2.24,1 2.24,1 2.24,1.323 false 1.375,0.125 1.719,0.125 1.719,0.125 1.875,0.208 false 1.219,0.052 1.396,0.208 0.177,0.156 10 false *1 2.188,1.333 2.365,1.51 0.177,0.177 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them to the direct multiple disc clutch assembly.

Bearing and Race Diameter
- Inside Outside
Bearing 28 mm (1.10 in.) 47.1 mm (1.85 in.)
Race 26.1 mm (1.03 in.) 44 mm (1.73 in.)

NOTICE:

Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.
C201321C01
1.302,0.292 0.531,0.406 0.531,0.406 0.531,0.469 false 0.49,0.479 0.667,0.667 0.177,0.188 10 *1
*1 Rear Planetary Sun Gear


Install the rear planetary sun gear assembly to the direct multiple disc clutch assembly.


c.
C202900

Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.


d.
C224456C01
1.771,0.229 1.948,0.229 false 1.625,1.917 1.458,1.917 false 1.979,0.156 2.167,0.323 0.188,0.167 10 *1 1.302,1.844 1.49,2.01 0.188,0.167 10 *2
*1 O-ring
*2 Oil Seal Ring


Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.

NOTICE:

Ensure that the O-ring is not twisted.



e.

Coat a new oil seal ring with ATF and install it to the direct multiple disc clutch assembly.


Hide 35650 54.INSTALL DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C202901C01
0.604,1.281 0.365,1.552 0.365,1.552 0.365,2.094 false 2.281,0.219 2.021,0.219 2.021,0.219 2.146,1.375 false 2.323,0.146 2.5,0.313 0.177,0.167 10 *1 0.313,2.115 0.49,2.271 0.177,0.156 10 *2
*1 Thrust Needle Roller Bearing
*2 Direct Multiple Disc Clutch Assembly


Coat the thrust needle roller bearing with ATF and install it on the transaxle case.

Bearing Diameter
- Inside Outside
Bearing 61.2 mm (2.41 in.) 79 mm (3.11 in.)


b.

Install the direct multiple disc clutch assembly to the transaxle case.


Hide 35102 56.INSTALL REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C205308N05
1.688,1.104 0.854,1.073 0.854,1.073 1.656,1.354 true 0.521,0.979 0.813,1.135 0.292,0.156 10 SST

Using SST and a hammer, install a new needle roller bearing into the rear transaxle cover sub-assembly.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)

Installation depth:

21.5 to 21.9 mm (0.847 to 0.862 in.)



b.
C201318

Clean and degrease the 2 "TORX" screws and the installation holes in the rear transaxle cover sub-assembly.


c.

Apply adhesive to 2 or 3 threads on the ends of the 2 "TORX" screws.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Using a T30 "TORX" socket wrench, install the rear transaxle cover plate to the rear transaxle cover sub-assembly with the 2 "TORX" screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.
C202908C01
1.385,1.75 1.385,0.125 1.385,0.125 1.885,0.125 false 1.604,1.635 1.604,0.125 false 0.698,2.438 0.5,2.563 0.5,2.563 0.5,2.646 false 1.021,0.719 1.115,0.719 1.115,0.719 1.115,1.823 false 1.917,0.031 2.125,0.219 0.208,0.188 10 *1 0.823,0.615 1.01,0.938 0.188,0.323 10 *2 0.448,2.656 0.719,2.958 0.271,0.302 10 *3
*1 Oil Seal Ring
*2 Thrust Needle Roller Bearing
*3 Thrust Needle Roller Race


Coat the thrust needle roller bearing and thrust needle roller race with MP grease and install them on the rear transaxle cover sub-assembly.

Bearing and Race Diameter
- Inside Outside
Bearing 48.9 mm (1.93 in.) 72.0 mm (2.83 in.)
Race 52.2 mm (2.06 in.) 70.4 mm (2.77 in.)


f.

Coat 2 new oil seal rings with ATF and install them to the rear transaxle cover sub-assembly.


g.
C274807

Coat 3 new O-rings with ATF and install them to the transaxle case.


h.
C138271

Remove packing material from the contact surfaces between the rear transaxle cover sub-assembly and transaxle case.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



i.

Apply seal packing to the transaxle case.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent.


NOTICE:
·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.

·

After applying seal packing, install the rear transaxle cover sub-assembly to the transaxle case within 3 minutes and tighten the bolts within 10 minutes.




j.
C280471

Install the rear transaxle cover sub-assembly to the transaxle case with the 12 bolts.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


k.
C280472

Clean and degrease the 2 bolts and the installation holes in the transaxle case.


l.

Apply adhesive to 2 or 3 threads on the ends of the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



m.

Install the 2 bolts.

Torque:
16.9 N*m (172 kgf*cm, 12 ft.*lbf)


n.
C162439

Install a new gasket to the refill plug.


o.

Install the refill plug to the rear transaxle cover sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 35145C 58.INSTALL TRANSAXLE CASE GASKET

a.
C201316

Coat 2 new transaxle case gaskets with ATF.


b.

Install the 2 transaxle case gaskets onto the transaxle case.


Hide 35410 59.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C280473C01
0.25,2.302 0.563,2.458 0.313,0.156 10 (*a) 3.094,1.427 3.406,1.583 0.313,0.156 10 (*a) 1.865,0.531 2.177,0.688 0.313,0.156 10 A 2.281,2.365 2.448,2.542 0.167,0.177 10 A 1.906,2.406 2.073,2.583 0.167,0.177 10 A 1.573,2.406 1.74,2.583 0.167,0.177 10 A 1.188,2.427 1.354,2.604 0.167,0.177 10 A 0.885,2.573 1.052,2.75 0.167,0.177 10 B 2.938,1.438 3.104,1.615 0.167,0.177 10 B 0.177,1.365 0.344,1.542 0.167,0.177 10 C 1.271,0.521 1.438,0.698 0.167,0.177 10 B 0.313,2.146 0.479,2.323 0.167,0.177 10 B 0.948,0.531 1.115,0.708 0.167,0.177 10 D
*a Positioning Bolt


Coat the O-ring of the transmission wire with ATF.


b.

Insert the pin of the manual valve lever into the groove on the end of the manual valve and install the transmission valve body assembly onto the transaxle case with the 11 bolts.

Bolt Length
Bolt Length
A 25 mm (0.984 in.)
B 30 mm (1.18 in.)
C and D 35 mm (1.38 in.)

Torque:
Bolt A, B, C : 10.8 N*m (110 kgf*cm, 8 ft.*lbf)
Bolt D : 9.6 N*m (98 kgf*cm, 85 in.*lbf)

NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case to interfere with each other.

·

First, temporarily tighten the bolts marked (*a) in the illustration because they are positioning bolts.




Hide 35330 60.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C201703

Coat a new O-ring with ATF.


b.

Install the O-ring onto the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted.



c.
C230619

Install the valve body oil strainer assembly onto the transmission valve body assembly with the 2 bolts.

Torque:
9.6 N*m (98 kgf*cm, 85 in.*lbf)


Hide 35106D 61.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C201701C01
2.748,0.131 2.969,0.338 0.222,0.207 10 *1 2.716,0.222 1.774,0.222 1.774,0.222 1.774,0.753 false 2.494,0.222 2.494,1.165 false
*1 Transmission Oil Cleaner Magnet


Install the 2 transmission oil cleaner magnets onto the automatic transaxle oil pan sub-assembly as shown in the illustration.


b.

Install a new automatic transaxle oil pan gasket onto the automatic transaxle oil pan sub-assembly.


c.
C202902

Install the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket onto the transaxle case with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surfaces of the transaxle case and automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket before installation.



d.
C202903

Clean and degrease the 2 bolts and the installation holes in the transaxle case.


e.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.

Install the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


g.
C201310

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


h.
C201309

Using a 6 mm hexagon socket wrench, install the overflow plug and a new gasket to the automatic transaxle oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 35104R 62.INSTALL TRANSAXLE CASE PLUG

a.
C134959

Clean and degrease the 3 No. 2 transaxle case plugs and the installation holes in the transaxle housing.


b.

Apply adhesive to 2 or 3 threads on the ends of the 3 transaxle case plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the 3 new gaskets to the 3 transaxle case plugs.


d.

Using a 6 mm hexagon socket wrench, install the 3 transaxle case plugs to the transaxle housing with the gaskets.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


e.
C279453

Coat 6 new O-rings with ATF and install them to the 6 transaxle case plugs.


f.

Install the 6 transaxle case plugs to the transaxle case and rear transaxle cover sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 32921C 63.INSTALL OIL COOLER TUBE UNION

a.
C279449

Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.


b.

Using a 19 mm union nut wrench, install the 2 oil cooler tube unions as shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 84540 64.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136686

Temporarily install the park/neutral position switch assembly to the transaxle case with the 2 bolts.

NOTICE:

Before installing the park/neutral position switch assembly, remove any dirt or rust on the manual valve lever shaft sub-assembly. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



b.
C135733C14
1.698,1.333 2.5,0.75 2.5,0.75 1.698,1.458 true 2.531,0.656 2.792,0.854 0.26,0.198 10 *a
*a Protrusion


Align the protrusions of the park/neutral position switch assembly as shown in the illustration.


c.

Tighten the 2 bolts

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the park/neutral position switch assembly are aligned.



d.
C136685

Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the washer and nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 35104V 65.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C134952C01
2.927,2.396 2.927,2.677 false 2,2.521 2.438,2.521 false 1.635,1.698 1.99,1.698 false 0.635,0.875 0.792,0.604 0.792,0.604 0.927,0.604 false 1.469,1.625 1.635,1.781 0.167,0.156 10 *2 0.958,0.531 1.135,0.688 0.177,0.156 10 *1 1.844,2.448 2,2.604 0.156,0.156 10 *3 2.875,2.688 3.042,2.854 0.167,0.167 10 *4
*1 No. 1 Breather Plug
*2 Breather Plug Hose
*3 No. 2 Breather Plug
*4 O-ring


Coat a new O-ring with ATF and install it to the No. 2 breather plug.

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the No. 2 breather plug to the breather plug hose.


c.

Install the No. 1 breather plug to the breather plug hose.


d.
C238851C05
2.313,1.25 2.396,1.49 2.396,1.49 2.5,1.49 true 2.563,1.042 2.719,0.625 2.719,0.625 2.854,0.625 true 2.521,1.385 2.75,1.573 0.229,0.188 10 *a 2.875,0.542 3.104,0.729 0.229,0.188 10 *1
*1 No. 2 Breather Plug
*a Boss


Install the transmission breather plug hose sub-assembly to the transaxle case.

NOTICE:

Ensure that the stopper on the No. 2 breather plug is in contact with the side of the boss on the transaxle case.