Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP
RM3090E _52 Drivetrain _008753 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0051091 OIL PUMP A

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  REASSEMBLY  


PROCEDURE

Hide 35301A 1.INSTALL FRONT OIL PUMP OIL SEAL

a.
C138515
2.599,1.442 2.951,1.635 0.352,0.193 10 SST 2.546,1.515 1.74,1.022 false

Coat the lip of a new front oil pump oil seal with a small amount of MP grease.


b.

Using SST and a hammer, install the front oil pump oil seal to the front oil pump body sub-assembly.

SST
09350-32014  (09351-32140)

NOTICE:

The seal end should be level with the outer edge of the front oil pump body sub-assembly.



Hide 35301B 2.INSTALL FRONT OIL PUMP BODY O-RING

a.
C138278

Coat a new front oil pump body O-ring with ATF and install it to the front oil pump body sub-assembly.

NOTICE:

Ensure that the O-ring is not twisted.



Hide 35322 3.INSTALL FRONT OIL PUMP DRIVEN GEAR

a.
C138277

Coat the front oil pump driven gear with ATF and install it to the front oil pump body sub-assembly with the marked side up.


Hide 35321 4.INSTALL FRONT OIL PUMP DRIVE GEAR

a.
C138276

Coat the front oil pump drive gear with ATF, and install it to the front oil pump body sub-assembly with the marked side up.


Hide 35370 5.INSTALL STATOR SHAFT ASSEMBLY

a.
C138275
1.417,2.625 1.563,2.792 0.146,0.167 10 B 0.771,1.198 0.917,1.365 0.146,0.167 10 A 1.031,0.583 1.177,0.75 0.146,0.167 10 A 1.656,0.333 1.802,0.5 0.146,0.167 10 A 2.271,0.531 2.417,0.698 0.146,0.167 10 A 2.583,0.979 2.729,1.146 0.146,0.167 10 A 2.563,1.625 2.708,1.792 0.146,0.167 10 A 2.219,2.115 2.365,2.281 0.146,0.167 10 A 1.729,2.24 1.875,2.406 0.146,0.167 10 A 0.99,1.885 1.125,2.052 0.135,0.167 10 A 2.229,2.802 2.375,2.969 0.146,0.167 10 B 2.438,3.354 2.583,3.521 0.146,0.167 10 B 2.385,4.052 2.531,4.219 0.146,0.167 10 B 0.854,3.823 1,3.99 0.146,0.167 10 B 0.896,3.125 1.042,3.292 0.146,0.167 10 B 1.354,4.26 1.5,4.427 0.146,0.167 10 B

Align each knock pin of the stator shaft assembly with the holes in the front oil pump body sub-assembly and install the stator shaft assembly to the front oil pump body sub-assembly with the 16 bolts.

Bolt Length
Bolt Length
A 14 mm (0.551 in.)
B 26 mm (1.02 in.)


b.

Using a T30 "TORX" socket wrench, tighten the 16 bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)