Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2012.12–2015.04
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Glass Breakage Sensor Circuit  


DESCRIPTION

When the glass breakage sensor detects that the back door glass, rear door quarter window glass LH or RH is tapped or broken, the sensor will set off the alarm for 30 seconds.

WIRING DIAGRAM

B341523E01
1.104,1.479 1.563,1.646 0.458,0.167 10 SSR+ 1.104,2.01 1.563,2.177 0.458,0.167 10 SSR- 1.583,1.906 2.042,2.073 0.458,0.167 10 1 1.583,1.344 2.042,1.51 0.458,0.167 10 2 0.427,2.26 0.885,2.427 0.458,0.167 10 M16 0.417,2.438 1.563,2.802 1.146,0.365 10 Rear Door Quarter Window Glass RH 1.104,3.948 1.563,4.115 0.458,0.167 10 SSR+ 1.125,4.479 1.583,4.646 0.458,0.167 10 SSR- 0.552,4.781 1.01,4.948 0.458,0.167 10 N10 0.552,4.979 1.688,5.396 1.135,0.417 10 Rear Door Quarter Window Glass LH 1.594,3.844 2.052,4.01 0.458,0.167 10 2 1.594,4.375 2.052,4.542 0.458,0.167 10 1 3.552,1.479 3.781,1.646 0.229,0.167 10 3D 3.552,1.292 3.781,1.458 0.229,0.167 10 38 5.083,1.479 5.313,1.646 0.229,0.167 10 A 5.042,1.302 5.271,1.469 0.229,0.167 10 19 5.333,1.469 6.104,1.667 0.771,0.198 10 GCS 3.625,2.052 5.24,2.375 1.615,0.323 10 Instrument Panel Junction Block Assembly 5.302,2.594 6.927,2.979 1.625,0.385 10 Main Body ECU (Multiplex Network Body ECU) 5.052,4.5 5.281,4.667 0.229,0.167 10 U2 5.094,4.344 5.323,4.51 0.229,0.167 10 2 5.313,4.51 5.771,4.677 0.458,0.167 10 SSR+ 6.042,4.5 6.198,4.688 0.156,0.188 10 E 6.302,4.5 6.458,4.688 0.156,0.188 10 B 6.302,4.344 6.458,4.531 0.156,0.188 10 1 5.25,4.917 6.438,5.104 1.188,0.188 10 Back Door Glass

CAUTION / NOTICE / HINT

NOTICE:

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.


PROCEDURE

1.READ VALUE USING GTS (GLASS BREAK SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sealed Glas Brak Sen Glass breakage sensor connecting With or Without With: Glass breakage sensor connected
Without: Glass breakage sensor not connected
-
Body Electrical > Main Body > Data List
Tester Display
Sealed Glas Brak Sen
50003 123 208
OK:

"With" (glass breakage sensor operating) appears on GTS screen.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - GLASS BREAKAGE SENSOR AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - GLASS BREAKAGE SENSOR AND BODY GROUND)
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Connect the instrument panel junction block assembly connectors.


c.

Disconnect the M16, N10, U2 and B glass breakage sensor connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-19 (GCS) - M16-2 (SSR+) Always Below 1 Ω
M16-1 (SSR-) - N10-2 (SSR+) Always Below 1 Ω
N10-1 (SSR-) - U2-2 (SSR+) Always Below 1 Ω
B-1 (E) - Body ground Always Below 1 Ω
A-19 (GCS) - Body ground Always 10 kΩ or higher
M16-2 (SSR+) - Body ground Always 10 kΩ or higher
M16-1 (SSR-) - Body ground Always 10 kΩ or higher
N10-2 (SSR+) - Body ground Always 10 kΩ or higher
N10-1 (SSR-) - Body ground Always 10 kΩ or higher
U2-2 (SSR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR DOOR QUARTER WINDOW GLASS RH

NG

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - GLASS BREAKAGE SENSOR)
3.INSPECT REAR DOOR QUARTER WINDOW GLASS RH
a.

Disconnect the M16 rear door quarter window glass RH connector.


b.
B240861N01
1.917,1.229 2.229,0.917 2.229,0.917 2.354,0.917 false 1.521,1.229 1.208,0.917 1.208,0.917 1.083,0.917 false 2.406,0.823 2.906,1.135 0.5,0.313 10 false SSR- 0.583,0.823 1.094,1.01 0.51,0.188 10 false SSR+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SSR+) - 1 (SSR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT REAR DOOR QUARTER WINDOW GLASS LH

NG

REPLACE REAR DOOR QUARTER WINDOW GLASS RH

4.INSPECT REAR DOOR QUARTER WINDOW GLASS LH
a.

Disconnect the N10 rear door quarter window glass LH connector.


b.
B240861N01
1.917,1.229 2.229,0.917 2.229,0.917 2.354,0.917 false 1.521,1.229 1.208,0.917 1.208,0.917 1.083,0.917 false 2.406,0.823 2.906,1.135 0.5,0.313 10 false SSR- 0.583,0.823 1.094,1.01 0.51,0.188 10 false SSR+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SSR+) - 1 (SSR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT BACK DOOR GLASS

NG

REPLACE REAR DOOR QUARTER WINDOW GLASS LH

5.INSPECT BACK DOOR GLASS
a.

Disconnect the U2 and B back door glass connectors.


b.
B341596N01
1.49,1.854 1.896,2.063 0.406,0.208 1.5,0.104 1.906,0.313 0.406,0.208 1.052,0.698 1.198,0.698 1.198,0.698 1.521,0.927 false 1.052,2.479 1.198,2.479 1.198,2.479 1.521,2.708 false 0.583,0.625 1.198,0.823 0.615,0.198 10 SSR+ 0.875,2.406 1.49,2.604 0.615,0.198 10 E 1.656,0.135 2.271,0.333 0.615,0.198 10 A 1.635,1.885 2.25,2.083 0.615,0.198 10 B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (SSR+) - B-1 (E) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - GLASS BREAKAGE SENSOR)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Disconnect the M16 glass breakage sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-38 (GCS) - M16-2 (SSR+) Always Below 1 Ω
3D-38 (GCS) - Body ground Always 10 kΩ or higher
M16-2 (SSR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR