1.INSPECT SHIFT LEVER ASSEMBLY (w/o Smart Key System)
| *a | Component with harness connected
(Floor Shift Lever Sub-assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ACC) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch ACC | 11 to 14 V | |
| Ignition switch off | Below 1 V | |
| 8 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| 5 (KLS+) - Body ground | Ignition switch ACC and shift lever in P | Below 1 V |
| Ignition switch ACC and shift lever except in P | 11 to 14 V | |
| 4 (IG) - Body - ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Do not disconnect the shift lever assembly connector.
If the result is not as specified, replace the shift lever assembly.
| *a | Component with harness connected
(Floor Shift Lever Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (E) - Body ground | Always | Below 1 Ω |
Do not disconnect the shift lever assembly connector.
If the result is not as specified, replace the shift lever assembly.
2.INSPECT SHIFT LEVER ASSEMBLY (w/ Smart Key System)
| *a | Component with harness connected
(Floor Shift Lever Sub-assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ACC) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Engine switch on (ACC) | 11 to 14 V | |
| Engine switch off | Below 1 V | |
| 8 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| 2 (P2) - Body ground | Engine switch on (ACC) and shift lever except in P | Below 1 V |
| Engine switch on (ACC) and shift lever in P | 11 to 14 V | |
| 4 (IG) - Body - ground | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V |
Do not disconnect the shift lever assembly connector.
If the result is not as specified, replace the shift lever assembly.
| *a | Component with harness connected
(Floor Shift Lever Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (E) - Body ground | Always | Below 1 Ω |
Do not disconnect the shift lever assembly connector.
If the result is not as specified, replace the shift lever assembly.
3.INSPECT TRANSMISSION CONTROL SWITCH
Disconnect the connector from the shift lever assembly.
| *A | for LHD |
| *a | Component without harness connected
(Transmission control switch) |
for LHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| 3 (SFTU) - 2 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| 1 (SFTD) - 2 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in S, "+" or "-" | 10 kΩ or higher |
| 3 (SFTU) - 2 (E) | Shift lever in S | 10 kΩ or higher |
| 1 (SFTD) - 2 (E) | Shift lever in S | 10 kΩ or higher |
If the result is not as specified, replace the shift lever assembly.
| *A | for RHD |
| *a | Component without harness connected
(Transmission control switch) |
for RHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| 1 (SFTU) - 2 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| 3 (SFTD) - 2 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in S, "+" or "-" | 10 kΩ or higher |
| 3 (SFTU) - 2 (E) | Shift lever in S | 10 kΩ or higher |
| 1 (SFTD) - 2 (E) | Shift lever in S | 10 kΩ or higher |
If the result is not as specified, replace the shift lever assembly.