Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0048745 NAVIGATION SYSTEM(for HDD) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation ECU sub-assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation ECU sub-assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination mete rassembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC No. Detection Item DTC Detection Condition Trouble Area
B15C2 Speed Signal Malfunction A difference between the GPS speed and SPD pulse is detected.
·

Meter/gauge System

·

Harness or connector

·

Navigation ECU sub-assembly



WIRING DIAGRAM

E270426E01
5.167,1.958 6.167,2.333 1,0.375 10 Navigation ECU Sub-assembly 1.063,1.792 1.396,1.958 0.333,0.167 10 G16 1.063,1.958 2.229,2.375 1.167,0.417 10 Combination Meter Assembly 5.156,1.792 5.573,1.958 0.417,0.167 10 G139 5.24,1.052 5.656,1.219 0.417,0.167 10 SPD 1.75,1.083 2.167,1.25 0.417,0.167 10 +S 2.083,0.917 2.5,1.083 0.417,0.167 10 6 4.917,0.917 5.333,1.083 0.417,0.167 10 17

PROCEDURE

1.CHECK VEHICLE SENSOR (OPERATION CHECK)

b.

While driving the vehicle, compare the "SPD" indicator to the reading on the speedometer. Check if these readings are equal or almost equal.


Result:
Proceed to
The readings are equal or almost equal
The readings are not equal or almost equal



The readings are equal or almost equal

The readings are not equal or almost equal

2.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E190309C01
0.198,1.333 0.677,1.604 0.479,0.271 0.677,0.99 2.646,0.99 false 0.885,1.99 1.615,1.99 false 1.719,1.99 2.521,1.99 false 2,1.49 2.542,2.198 2.542,2.198 2.646,2.198 true 0.073,0.063 0.333,0.25 0.26,0.188 10 *a 0.292,1.385 0.583,1.542 0.292,0.156 10 G16 1.167,4.042 1.365,4.198 0.198,0.156 10 A 2.698,2.115 2.99,2.271 0.292,0.156 10 +S 2.813,3.479 3.198,3.635 0.385,0.156 10 GND
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform

i.

Remove the combination meter assembly with theconnector(s) still connected.


ii.

Connect an oscilloscope to terminal G16-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to thecondition(s) in the table below.

Item Condition
Measurement terminal G16-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheelrevolution generates 4 pulses. As the vehicle speedincreases, the width indicated by A in the illustrationnarrows.




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G139 navigation ECU sub-assemblyconnector.


b.

Disconnect the G16 combination meter assemblyconnector.


c.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-17 (SPD) - G16-6 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR