Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) › 2012.12–2015.04
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0051218 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (example if a door lock operation is requested, the certification ECU [smart key ECU assembly] sends a door lock command to the main body ECU [multiplex network body ECU]).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short in RDAM to ground between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in CSEL to ground between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in RDAM to ground when RCO (5 V) output from the ECU is off.


·

Harness or connector

·

Door control receiver

·

Certification ECU (Smart key ECU assembly)



WIRING DIAGRAM

B265620E10
2.188,2.115 3.052,2.323 0.865,0.208 10 false 12*1, 1*2 0.792,2.813 2.5,3.229 1.708,0.417 10 false Door Control Receiver 5.073,2.708 6.656,3.427 1.583,0.719 10 false Certification ECU (Smart Key ECU Assembly) 0.792,2.688 1.948,2.854 1.156,0.167 10 false M11*1, M10*2 1.927,0.677 2.365,1.063 0.438,0.385 10 false +5 1.719,1.156 2.573,1.74 0.854,0.583 10 false DATA 4.875,2.229 5.365,2.583 0.49,0.354 10 false G82 4.885,1.646 5.344,1.979 0.458,0.333 10 false G83 4.875,1.156 5.344,1.448 0.469,0.292 10 false G83 4.906,2.042 5.844,2.74 0.938,0.698 10 false 11 4.958,1.458 5.313,1.771 0.354,0.313 10 false 6 4.917,0.958 5.26,1.198 0.344,0.24 10 false 17 4.948,0.479 5.198,0.708 0.25,0.229 10 false 5 4.875,0.677 5.438,1.052 0.563,0.375 10 false G83 5.26,0.677 5.802,0.948 0.542,0.271 10 false RCO 5.25,1.156 5.938,1.542 0.688,0.385 10 false RDAM 5.26,2.229 5.781,2.583 0.521,0.354 10 false E 5.26,1.646 6.094,2.188 0.833,0.542 10 false CSEL 1.688,2.26 2.365,2.688 0.677,0.427 10 false GND*2 1.729,1.646 2.396,2.083 0.667,0.438 10 false CSEL 2.188,1.542 2.896,1.74 0.708,0.198 10 false 6*1, 2*2 2.188,1.052 2.938,1.219 0.75,0.167 10 false 9*1, 5*2 2.188,0.563 2.927,0.771 0.74,0.208 10 false 10*1, 4*2 1.865,2.104 2.542,2.531 0.677,0.427 10 false E*1 0.115,3.167 1.271,3.333 1.156,0.167 10 false *1: for 12 Pin Type 0.115,3.448 2.375,3.646 2.26,0.198 10 false *2: except 12 Pin Type

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.

·

This DTC is not detected within 10 seconds after the engine switch is turned to off from ON.

·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B299802C04
0.542,0.375 0.917,0.594 0.375,0.219 1.875,0.365 2.25,0.583 0.375,0.219 2.656,1.198 2.792,0.458 2.792,0.458 2.917,0.458 false 2.656,1.354 2.708,1.906 2.708,1.906 2.833,1.906 false 1.156,1.375 1.156,1.969 1.156,1.969 1.281,1.969 false 0.594,0.396 1.052,0.594 0.458,0.198 10 G82 1.927,0.396 2.385,0.594 0.458,0.198 10 G83 2.958,0.385 3.417,0.583 0.458,0.198 10 RCO 2.854,1.823 3.313,2.021 0.458,0.198 10 RDAM 1.333,1.896 1.792,2.094 0.458,0.198 10 E 0.094,0.073 0.406,0.271 0.313,0.198 10 *a
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])


Disconnect the M11*1 or M10*2 door control receiver connector.

*1: for 12 Pin Type

*2: except 12 Pin Type



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G83-5 (RCO) - Body ground Always Below 1 V → 4.5 to 5.5 V
(Pulse generation)
G83-17 (RDAM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL RECEIVER

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the M11*1 or M10*2 door control receiver connector.

*1: for 12 Pin Type

*2: except 12 Pin Type



b.

Disconnect the G82 and G83 certification ECU (smart key ECU assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 12 Pin Type
Tester Connection Condition Specified Condition
G83-6 (CSEL) - M11-6 (CSEL) Always Below 1 Ω
G83-17 (RDAM) - M11-9 (DATA) Always Below 1 Ω
G83-5 (RCO) - M11-10 (+5) Always Below 1 Ω
M11-12 (E) - Body ground Always Below 1 Ω
G83-6 (CSEL) - Body ground Always 10 kΩ or higher
M11-6 (CSEL) - Body ground Always 10 kΩ or higher
G83-17 (RDAM) - Body ground Always 10 kΩ or higher
M11-9 (DATA) - Body ground Always 10 kΩ or higher
G83-5 (RCO) - Body ground Always 10 kΩ or higher
M11-10 (+5) - Body ground Always 10 kΩ or higher

except 12 Pin Type
Tester Connection Condition Specified Condition
G83-6 (CSEL) - M10-2 (CSEL) Always Below 1 Ω
G83-17 (RDAM) - M10-5 (DATA) Always Below 1 Ω
G83-5 (RCO) - M10-4 (+5) Always Below 1 Ω
M10-1 (GND) - Body ground Always Below 1 Ω
G83-6 (CSEL) - Body ground Always 10 kΩ or higher
M10-2 (CSEL) - Body ground Always 10 kΩ or higher
G83-17 (RDAM) - Body ground Always 10 kΩ or higher
M10-5 (DATA) - Body ground Always 10 kΩ or higher
G83-5 (RCO) - Body ground Always 10 kΩ or higher
M10-4 (+5) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR