Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) › 2012.12–2016.08
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0051218 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function* does not operate. In such cases, hazard warning light and wireless door lock buzzer* signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

*: w/ Wireless Door Lock Buzzer Answer Back Function


WIRING DIAGRAM

B343414E01
2.531,0.49 4.969,0.781 2.438,0.292 10 false Hazard Warning Signal Switch Signal 5.583,2.927 6.896,3.448 1.313,0.521 10 false Combination Meter Assembly 5.573,2.76 6.01,2.958 0.438,0.198 10 false G17 2.813,4.125 4.5,4.49 1.688,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 2.813,3.958 3.25,4.156 0.438,0.198 10 false A 3.771,2.948 4.208,3.146 0.438,0.198 10 false BZR 3.438,2.813 3.875,3.01 0.438,0.198 10 false 21 2.198,2.813 2.635,3.01 0.438,0.198 10 false 55 0.552,3.594 2.365,3.896 1.813,0.302 10 false Wireless Door Lock Buzzer 0.563,3.427 1,3.625 0.438,0.198 10 false A12 1.604,2.938 2.042,3.135 0.438,0.198 10 false B 0.865,2.938 1.302,3.135 0.438,0.198 10 false E 1.885,2.823 2.323,3.021 0.438,0.198 10 false 1 0.594,2.823 1.031,3.021 0.438,0.198 10 false 2 5.74,0.49 6.177,0.688 0.438,0.198 10 false HAZ 5.49,0.365 5.927,0.563 0.438,0.198 10 false 3 0.802,5.354 2.875,5.635 2.073,0.281 10 false : CAN Communication Line 2.729,5.25 5.625,5.51 2.896,0.26 10 false Instrument Panel Junction Block Assembly 2.719,5.104 3.156,5.302 0.438,0.198 10 false 3B

CAUTION / NOTICE / HINT

NOTICE:
·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.READ VALUE USING GTS (Hazard Answer Back, Wireless Buzzer Resp, Wireless Buzzer Vol)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Customize Setting / Wireless Door Lock.


e.

Select the setting by referring to the table below.

Wireless Door Lock
Tester Display Description Default Setting ECU
Hazard Answer Back When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Resp Wireless door lock buzzer response*1 ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Vol Wireless door lock buzzer volume*1 Level 5*2
Level 7*3
0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 Main body ECU (Multiplex network body ECU)
50006 1

*1: w/ Wireless Door Lock Buzzer Answer Back Function

*2: w/ Power Back Door System

*3: w/o Power Back Door System



Result:
Proceed to
Both items are ON and except Level 0
Either item is OFF or Level 0



Both items are ON and except Level 0

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

Either item is OFF or Level 0

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the electrical key transmitter sub-assembly.


Result:
Proceed to
Wireless door lock/unlock operates properly
Wireless door lock/unlock does not operate properly



Wireless door lock/unlock operates properly

3.READ VALUE USING GTS (FR Door Lock Pos, FL Door Lock Pos, RR-Door Lock Pos SW, RL-Door Lock Pos SW)

Wireless door lock/unlock does not operate properly

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

3.READ VALUE USING GTS (FR Door Lock Pos, FL Door Lock Pos, RR-Door Lock Pos SW, RL-Door Lock Pos SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
RR-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
*1
RL-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
*2

*1: When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.

*2: When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.


Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52
OK:

The display on the GTS changes according to the detection condition of the door unlock detection switch.



Result:
Proceed to
OK
NG



OK

4.CHECK WIRELESS ANSWER-BACK OPERATION

NG

GO TO LIGHTING SYSTEM (INT) (Proceed to Door Unlock Detection Switch Circuit)

4.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the electrical key transmitter sub-assembly.


Result:
Proceed to

*: w/ Wireless Door Lock Buzzer Answer Back Function

Only wireless door lock buzzer answer-back does not occur*
Only hazard warning light answer-back does not occur



Only wireless door lock buzzer answer-back does not occur*

5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)

Only hazard warning light answer-back does not occur

10.CHECK HAZARD WARNING LIGHTS OPERATION
5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Wireless Buzzer Wireless door lock buzzer OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

Result:
Proceed to
Wireless door lock buzzer does not turn on or off
Wireless door lock buzzer turns on or off (for LHD)
Wireless door lock buzzer turns on or off (for RHD)



Wireless door lock buzzer does not turn on or off

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

Wireless door lock buzzer turns on or off (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Wireless door lock buzzer turns on or off (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A12 wireless door lock buzzer connector.


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-1 (B) - 3B-55 Always Below 1 Ω
A12-2 (E) - Body ground Always Below 1 Ω
A12-1 (B) - Body ground Always 10 kΩ or higher
3B-55 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL

B337496C02
2,1 2.417,1.25 0.417,0.25 5.417,0.667 5.833,0.917 0.417,0.25 2.198,2.271 2.615,2.271 2.615,2.271 2.615,1.688 false 5.542,0.719 5.854,0.917 0.313,0.198 10 3B 2.146,1.052 2.458,1.25 0.313,0.198 10 A 1.896,2.188 2.208,2.385 0.313,0.198 10 BZR


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-55 - A-21 (BZR) Always Below 1 Ω
3B-55 or A-21 (BZR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

8.REPLACE WIRELESS DOOR LOCK BUZZER

NG (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Temporarily replace the wireless door lock buzzer with a new one or normally functioning one.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
a.

Check the operation of the wireless answer-back function.

OK:

Wireless answer-back function operates normally.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE)

NG (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

10.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning lights blink when the hazard warning signal switch is pressed.

OK:

Hazard warning lights blink.



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

OK (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit)