Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) › 2012.12–2015.04
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0051219 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


C278789N02
0.479,5.302 0.896,5.583 0.417,0.281 2.542,5.208 2.958,5.49 0.417,0.281 5.615,5.229 6.031,5.51 0.417,0.281 1.781,6.969 2.198,7.25 0.417,0.281 5.448,7.042 5.865,7.323 0.417,0.281 2.333,1.229 2.615,1.427 0.281,0.198 10 3B 3.01,0.938 3.292,1.135 0.281,0.198 10 3E 3.656,1.083 3.938,1.281 0.281,0.198 10 3C 4.344,1.208 4.625,1.406 0.281,0.198 10 3D 2.271,2.969 2.552,3.167 0.281,0.198 10 3A 0.604,5.365 0.885,5.563 0.281,0.198 10 3A 2.677,5.271 2.958,5.469 0.281,0.198 10 3B 5.729,5.292 6.01,5.49 0.281,0.198 10 3C 1.917,7.031 2.198,7.229 0.281,0.198 10 3D 5.573,7.104 5.854,7.302 0.281,0.198 10 3E

C278790C04
1.333,3.667 1.75,3.896 0.417,0.229 2.531,5.563 2.948,5.792 0.417,0.229 3.333,7.438 3.75,7.667 0.417,0.229 1.365,7.458 1.781,7.688 0.417,0.229 1.25,5.25 1.417,5.25 1.417,5.25 1.667,4.833 false 1.083,7.25 1.333,7.25 1.333,7.25 1.583,7 false 2.667,1.656 2.823,1.854 0.156,0.198 10 A 1.5,3.698 1.656,3.896 0.156,0.198 10 A 0.313,4.281 0.563,4.458 0.25,0.177 10 *A 1.083,5.167 1.333,5.344 0.25,0.177 10 *1 2.615,5.594 3.052,5.76 0.438,0.167 10 G78 3.406,7.469 3.865,7.635 0.458,0.167 10 G78 1.427,7.49 1.781,7.667 0.354,0.177 10 G79 0.917,7.167 1.167,7.344 0.25,0.177 10 *1 0.281,6.646 0.531,6.823 0.25,0.177 10 *B
*A Main Body ECU (Multiplex Network Body ECU) with 1 connector *B Main Body ECU (Multiplex Network Body ECU) with 3 connectors
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (Multiplex network body ECU) from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

A-11 (GND1) - Body ground - Ground Always Below 1 Ω
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-32 (IG) - Body ground - Ignition power supply Ignition switch ON 11 to 14 V*1
10.5 to 14 V*2
A-32 (IG) - Body ground - Ignition power supply Ignition switch off Below 1 V



d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition

*1: w/ Theft Deterrent System or Double Locking System

*2: for LHD

*3: for RHD

3E-1 (ACT-) - Body ground BR - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3E-1 (ACT-) - Body ground BR - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-5 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-5 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-4 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-4 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-3 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-3 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-13 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3D-13 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-11 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3D-11 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-12 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3D-12 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3E-17 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked Below 1 V
3E-17 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3E-40 (FLCY) - Body ground W - Body ground Front door LH courtesy light switch input Front door LH open Below 1 V
3E-40 (FLCY) - Body ground W - Body ground Front door LH courtesy light switch input Front door LH closed Pulse generation
G78-19 (FRCY) - Body ground L - Body ground Front door RH courtesy light switch input Front door RH open Below 1 V
G78-19 (FRCY) - Body ground L - Body ground Front door RH courtesy light switch input Front door RH closed Pulse generation
G78-24 (LCTY) - Body ground W - Body ground*2
SB - Body ground*3
Rear door LH courtesy light switch input Rear door LH open Below 1 V
G78-24 (LCTY) - Body ground W - Body ground*2
SB - Body ground*3
Rear door LH courtesy light switch input Rear door LH closed Pulse generation
G78-6 (RCTY) - Body ground Y - Body ground Rear door RH courtesy light switch input Rear door RH open Below 1 V
G78-6 (RCTY) - Body ground Y - Body ground Rear door RH courtesy light switch input Rear door RH closed Pulse generation
G78-7 (LSFL) - Body ground B - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V
G78-7 (LSFL) - Body ground B - Body ground Front door LH unlock detection switch input Front door LH locked Pulse generation
G78-18 (LSFR) - Body ground P - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V
G78-18 (LSFR) - Body ground P - Body ground Front door RH unlock detection switch input Front door RH locked Pulse generation
3E-32 (LSR) - Body ground*1 Y - Body ground Rear door RH unlock detection switch input Rear door RH or LH unlocked Below 1 V
3E-32 (LSR) - Body ground*1 Y - Body ground Rear door RH unlock detection switch input Rear door RH and LH locked Pulse generation
3C-41 (LSR) - Body ground*1 Y - Body ground Rear door LH unlock detection switch input Rear door LH or RH unlocked Below 1 V
3C-41 (LSR) - Body ground*1 Y - Body ground Rear door LH unlock detection switch input Rear door LH and RH locked Pulse generation
G78-4 (PRG) - Body ground W - Body ground Signal output to door control receiver Key inserted into ignition key cylinder → Key pulled out of ignition key cylinder 11 to 14 V → Pulse generation → 11 to 14 V
G78-16 (RDA) - Body ground SB - Body ground Signal input from door control receiver Ignition switch off, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch off, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)
G78-17 (KSW) - Body ground R - Body ground Key unlock warning switch input No key in ignition key cylinder Pulse generation
G78-17 (KSW) - Body ground R - Body ground Key unlock warning switch input Key in ignition key cylinder Below 1 V



CHECK DOOR CONTROL RECEIVER (for 12 Pin Type)


a.

Disconnect the M11 door control receiver connector.

B153407N03
3.271,0.115 3.708,0.344 0.438,0.229 3.365,0.156 3.823,0.354 0.458,0.198 10 M11


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
M11-7 (+B) - Body ground R - Body ground Battery power supply Always 11 to 14 V
M11-12 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the M11 door control receiver connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M11-5 (PRG) - M11-12 (E) W - W-B Signal input from main body ECU (multiplex network body ECU) Key inserted into ignition key cylinder → Key pulled out of ignition key cylinder 11 to 14 V → Pulse generation → 11 to 14 V
M11-4 (RDA) - M11-12 (E) G - W-B Signal output to main body ECU (multiplex network body ECU) Ignition switch off, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch off, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)



CHECK DOOR CONTROL RECEIVER (except 12 Pin Type)


a.

Disconnect the M10 door control receiver connector.

B280754N14
3.406,0.24 3.76,0.448 0.354,0.208 3.469,0.26 3.76,0.406 0.292,0.146 10 M10


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M10-5 (DATA) - Body ground Y - Body ground Battery power supply Always 11 to 14 V
M10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the M10 door control receiver connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M10-3 (PRG) - M10-1 (GND) Y - W-B Signal input from main body ECU (multiplex network body ECU) Key inserted into ignition key cylinder → Key pulled out of ignition key cylinder 11 to 14 V → Pulse generation → 11 to 14 V
M10-2 (CSEL) - M10-1 (GND) R - W-B Signal output to main body ECU (multiplex network body ECU) Ignition switch off, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch off, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)