Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0051219 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) M

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  REGISTRATION  


CAUTION / NOTICE / HINT

HINT:
·

Register a new recognition code when replacing the door control transmitter assembly or the door control receiver.

·

Add mode is used to retain the codes that have already been registered while registering a new recognition code. This mode is used when adding a door control transmitter assembly.

·

Rewrite mode is used to clear all the previously registered codes and register only new recognition codes. This mode is used when exchanging the door control transmitter assembly or the door control receiver with a new one.

·

Confirmation mode is used to confirm how many recognition codes have already been registered before additional registration of a recognition code.

·

Prohibition mode is used to clear all the registered codes and cancel the wireless door lock function. Use this mode when the door control transmitter assembly is lost.

·

All of the steps in the following registration procedure must be performed in sequential order continuously.



PROCEDURE

Hide 1. REGISTRATION OF RECOGNITION CODE (USING GTS [w/o Manual Registration])

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Utility / Wireless Code Registration.

Body Electrical > Main Body > Utility
Tester Display
Wireless Code Registration
50005 123 233

e.

Select either add or rewrite mode according to the GTS display.


f.

The number of registered codes is indicated.


g.

Registration of the door control transmitter assembly

i.

If either add mode or rewrite mode has been selected, press the lock and unlock switches on the door control transmitter assembly simultaneously.


ii.

Within 3 seconds of releasing the lock and unlock switches, press either of the switches on the door control transmitter assembly.

NOTICE:
·

Do not press the lock and unlock switches simultaneously for more than 1.5 seconds.

·

Perform this operation within 1 meter of the driver seat to register the door control transmitter assembly.

·

Do not push other door control transmitter assembly switches during the door control transmitter assembly registration process.




iii.

The main body ECU (multiplex network body ECU) automatically performs the power door lock/unlock operation once in order to indicate whether registration has been completed correctly or not.


iv.

If continuing registration, the next recognition code must be registered in the door control transmitter assembly within 30 seconds.

HINT:

Up to 6 recognition codes can be registered.




h.

Completing the registration mode.

i.

Registration mode will end when any of the following occurs:

·

30 seconds or more have elapsed after a code is registered.

·

The GTS is used to finish registration.

·

The GTS is disconnected.

·

The ignition switch is turned off.




i.

Perform the following after registration is completed.

i.

Perform the wireless door lock control operation check.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>OPERATION CHECK

HINT:

If the wireless door lock control does not operate, perform the registration procedure again.




Hide 2. REGISTRATION OF RECOGNITION CODE (NOT USING GTS [w/ Manual Registration])

a.

The following conditions must be met.

·

No key is inserted in the ignition key cylinder.

·

The driver side door is open (the other doors are closed).

·

The driver side door is unlocked.



b.

Insert and remove the key into/from the ignition key cylinder twice (Insert → Remove → Insert → Remove) within 5 seconds.

HINT:

The procedure should end with the key removed.



c.

Perform the following operations within 40 seconds.

i.

Close and open the driver side door twice (Close → Open → Close → Open).

HINT:

The procedure should end with the door open.



ii.

Insert and remove the key into/from the ignition key cylinder (Insert → Remove).

HINT:

The procedure should end with the key removed.



iii.

Close and open the driver side door twice (Close → Open → Close → Open).

HINT:

The procedure should end with the door open.



iv.

Insert the key into the ignition key cylinder and close all the doors.



d.

Perform the following operations within 40 seconds.

i.

Turn the ignition switch from ON to off at approximately 1 second intervals. Operate the ignition switch according to the number of times shown below.

B111914
0.25,0.802 0.917,0.979 0.667,0.177 10 Add Mode 0.083,0.083 3.979,0.271 3.896,0.188 12 Number of ON - off operations of ignition switch: 1.5,0.75 3.479,0.969 1.979,0.219 10 ON - off operation: Once 0.458,1.552 1.021,1.729 0.563,0.177 10 ON 0.49,1.885 1.115,2.094 0.625,0.208 10 off 1.292,1.24 1.479,1.417 0.188,0.177 10 T1 3.729,0.802 4.625,0.979 0.896,0.177 10 Rewrite Mode 5.021,0.75 7.094,0.969 2.073,0.219 10 ON - off operation: Twice 3.969,1.552 4.594,1.729 0.625,0.177 10 ON 4.042,1.885 4.667,2.094 0.625,0.208 10 off 4.792,1.24 4.979,1.417 0.188,0.177 10 T1 5,1.24 5.188,1.417 0.188,0.177 10 T1 0.219,2.813 1.417,2.99 1.198,0.177 10 Confirmation Mode 1.5,2.771 3.583,2.99 2.083,0.219 10 ON - off operation: 3 times 0.417,3.583 1.083,3.76 0.667,0.177 10 ON 0.458,3.906 1.083,4.115 0.625,0.208 10 off 4.771,3.24 4.958,3.417 0.188,0.177 10 T1 4.99,3.24 5.177,3.417 0.188,0.177 10 T1 1.26,3.24 1.448,3.417 0.188,0.177 10 T1 1.469,3.24 1.656,3.417 0.188,0.177 10 T1 3.729,2.823 4.927,3 1.198,0.177 10 Prohibition Mode 5.021,2.76 7.052,2.948 2.031,0.188 10 ON - off operation: 5 times 3.969,3.583 4.604,3.76 0.635,0.177 10 ON 4.031,3.906 4.656,4.115 0.625,0.208 10 off 0.094,4.333 2.292,4.615 2.198,0.281 10 T1: Approximately 1 second

HINT:

If the number of ignition switch ON - off operations is 0, 4, 6 or more, there will be no response (the power door lock and unlock operation) to show which mode has been selected.



ii.

Remove the key from the ignition key cylinder.



e.

Check the response to the selected mode within 5 seconds.

B222617
0.292,1.094 0.958,1.271 0.667,0.177 10 false Add Mode 1.49,1.083 3.542,1.302 2.052,0.219 10 false Lock-unlock operation: Once 1.292,1.521 1.479,1.698 0.188,0.177 10 false T1 3.76,1.094 4.656,1.271 0.896,0.177 10 false Rewrite Mode 5.042,1.063 7.146,1.281 2.104,0.219 10 false Lock-unlock operation: Twice 4.792,1.531 4.979,1.708 0.188,0.177 10 false T1 5.01,1.531 5.198,1.708 0.188,0.177 10 false T1 0.052,0.021 4.792,0.208 4.74,0.188 12 false Response to selected mode (power door lock operation): 0.125,0.375 6.698,0.792 6.573,0.417 10 false Main body ECU automatically performs power door lock-unlock operations to indicate which mode has been selected. 0.229,3.104 1.427,3.281 1.198,0.177 10 false Confirmation Mode 1.5,3.104 6.073,3.323 4.573,0.219 10 false Lock-unlock operation: Number of registered codes (1 to 5 times) 0.427,4.198 0.771,4.375 0.344,0.177 10 false Lock 0.333,4.521 0.802,4.729 0.469,0.208 10 false Unlock 0.417,1.896 0.76,2.073 0.344,0.177 10 false Lock 0.302,2.198 0.771,2.406 0.469,0.208 10 false Unlock 3.875,1.875 4.219,2.052 0.344,0.177 10 false Lock 3.802,2.208 4.271,2.417 0.469,0.208 10 false Unlock 0.521,6.125 0.865,6.302 0.344,0.177 10 false Lock 0.406,6.469 0.875,6.677 0.469,0.208 10 false Unlock 1.396,3.938 1.583,4.115 0.188,0.177 10 false T2 1.781,3.948 1.969,4.125 0.188,0.177 10 false T2 1.396,3.521 1.958,3.719 0.563,0.198 10 false 1st Time 2.167,3.531 2.771,3.729 0.604,0.198 10 false 2nd Time 0.271,5.438 1.469,5.615 1.198,0.177 10 false Prohibition Mode 1.5,5.448 3.667,5.667 2.167,0.219 10 false Lock-unlock operation: 5 times 0.188,7.427 2.313,7.688 2.125,0.26 10 false T2: Approximately 2 seconds 0.188,7.104 2.115,7.313 1.927,0.208 10 false T1: Approximately 1 second 1.354,5.802 1.542,5.979 0.188,0.177 10 false T1 1.573,5.802 1.76,5.979 0.188,0.177 10 false T1

NOTICE:

After the system has been set to prohibition mode, enter the confirmation mode and check that the number of registered keys is 0.


HINT:
·

In confirmation mode, the lock-unlock operation will occur once for each recognition code that has been registered. For example, if 2 recognition codes have been registered, the lock-unlock operation will occur twice.

·

In confirmation mode, if no recognition codes have been registered, the lock-unlock operation will occur 5 times.

·

If confirmation mode or prohibition mode is selected, the operation ends after the response to the selected mode completes.




f.

If add mode or rewrite mode is selected, perform the following procedures within 40 seconds.

i.

Press a door lock control transmitter switch (lock and unlock).


ii.

Press a door lock control transmitter switch (lock or unlock).


iii.

After completing the above step, check the response to the registration completion within 5 seconds.

B111915
0.229,1.396 2.115,1.573 1.885,0.177 10 Lock-unlock Occurs Once 4.115,1.396 6.031,1.573 1.917,0.177 10 Lock-unlock Occurs Twice 1.292,2.5 1.479,2.677 0.188,0.177 10 T1 4.313,2.792 4.635,2.969 0.323,0.177 10 Lock 4.167,3.115 4.625,3.323 0.458,0.208 10 Unlock 0.438,2.792 0.76,2.969 0.323,0.177 10 Lock 0.292,3.115 0.75,3.323 0.458,0.208 10 Unlock 5.167,2.469 5.354,2.646 0.188,0.177 10 T1 5.375,2.469 5.563,2.646 0.188,0.177 10 T1 0.083,0.021 3.583,0.208 3.5,0.188 12 Response to registration completion: 0.188,3.448 2.271,3.656 2.083,0.208 10 T1: Approximately 1 second 0.208,0.615 6.938,1 6.729,0.385 10 Main body ECU automatically performs power door lock-unlock operation to show whether registration has been completed correctly or not. 0.188,1.927 2.438,2.333 2.25,0.406 10 Registration of recognition code has been completed. 4.073,1.927 6.323,2.333 2.25,0.406 10 Registration of recognition code has failed.

HINT:
·

If the lock-unlock operation occurs twice, the registration of the recognition code has failed. Perform the registration procedures again from the beginning.

·

If registering another transmitter, repeat the procedures after the response to the selected mode confirmation. All 6 recognition codes can be registered consecutively.





g.

Perform either of the following to complete the registration of the recognition codes:

·

Open a door.

·

Insert the key into the ignition key cylinder.