Home › Drivetrain › EB61F MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE
RM3090E _52 Drivetrain _008758 EB61F MANUAL TRANSMISSION / TRANSAXLE _0050278 TRANSMISSION CONTROL CABLE N

EB61F MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  ADJUSTMENT  


PROCEDURE

Hide 33820B 1.ADJUST TRANSAXLE CONTROL CABLE ASSEMBLY

HINT:
·

After the shift lever or the shift cable is replaced, be sure to adjust the transmission control cable assembly.

·

If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to reverse without pulling up the slider shaft, the length of the cable must be adjusted.



a.
C284480
1.635,1.635 1.635,1.479 1.635,1.479 2.271,1.479 false 0.792,2.125 1.073,2.125 false 1.833,2.656 1.833,2.458 1.833,2.458 2.375,2.458 false 2.469,3.156 1.573,3.167 1.573,3.167 1.573,3.073 false 0.365,1.458 0.677,1.656 0.313,0.198 10 false *a 2.344,1.406 2.656,1.604 0.313,0.198 10 false *1 0.615,2.042 0.927,2.24 0.313,0.198 10 false *2 1.458,2.25 1.771,2.448 0.313,0.198 10 false *c 0.396,2.438 0.708,2.635 0.313,0.198 10 false *b 2.448,2.385 2.76,2.583 0.313,0.198 10 false *1 2.521,3.063 2.833,3.26 0.313,0.198 10 false *3
*1 Case
*2 Lock Piece
*3 Slider
*a Lock Release Condition
*b Lock Condition
*c Pull


Release the lock (lock condition to lock release condition).


b.
C277992
2.083,0.813 2.938,0.323 2.938,0.323 3.083,0.323 false 0.438,1.052 1.927,1.042 false 3.135,0.281 3.406,0.563 0.271,0.281 10 *1 0.271,0.969 0.573,1.26 0.302,0.292 10 *a
*1 Select Outer Lever
*a Hole


Align the hole of the select outer lever with the hole in the manual transmission case.


c.
C277993

Insert a bolt into the aligned holes to fix the select outer lever in place.

NOTICE:

In order to avoid case damage, do not push the bolt in forcefully.


HINT:
·

Use a bolt with a diameter of 6 mm (0.236 in.) and a length of at least 16 mm (0.630 in.).

·

Depending on the actual bolt diameter, it may be difficult to insert the bolt. In that case, as there is some variation in actual bolt diameters, use a 6.0 mm (0.236 in.) bolt with a comparatively small diameter.




d.
C277909C01
1.896,0.042 2.208,0.24 0.313,0.198 10 false *a
*a Reverse Direction


Move the shift lever in the reverse direction without pulling up the slider shaft.


e.
C277908
1.552,3.073 1.552,3.167 1.552,3.167 2.323,3.167 false 1.729,1.625 1.729,1.469 1.729,1.469 2.406,1.479 false 1.719,2.667 1.719,2.448 1.719,2.448 2.438,2.448 false 0.615,2.135 1.063,2.125 false 0.427,1.438 0.74,1.635 0.313,0.198 10 *a 0.49,2.427 0.802,2.625 0.313,0.198 10 *b 2.385,3.063 2.677,3.281 0.292,0.219 10 *3 2.469,1.406 2.781,1.604 0.313,0.198 10 *1 2.51,2.365 2.823,2.563 0.313,0.198 10 *1 1.427,2.229 1.74,2.427 0.313,0.198 10 *c 0.427,2.052 0.719,2.313 0.292,0.26 10 *2
*1 Case
*2 Lock Piece
*3 Slider
*a Lock Release Condition
*b Lock Condition
*c Push


While holding the shift lever in the reverse direction, lock the cable length adjustment mechanism of the select control cable.


f.
C277993

Remove the bolt to free the select outer lever.


g.
C277910

For new shift lever:

Remove the stopper pin and dispose of it.