The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.
The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
w/ Entry and Start System:
Before performing this troubleshooting, perform troubleshooting for "Back Door Entry Unlock Function does not Operate" for the Entry and start system (for Entry Function) first.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Check the vehicle specification.
| Proceed to |
|---|
| w/o Entry and Start System |
| w/ Entry and Start System |
w/o Entry and Start System
w/ Entry and Start System
Check the power door lock basic functions.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
The power door lock basic functions operate properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List / All Data.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Open | Back door lock signal | Permit or Prohibit | Permit: Back door unlocked
Prohibit: Back door locked |
- |
| Tester Display |
|---|
| Back Door Open |
The GTS indicates Permit or Prohibit according to the door lock operation shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Trunk and Back-Door Open | Back door lock motor | OFF/ON | - |
| Tester Display |
|---|
| Trunk and Back-Door Open |
The back door lock assembly unlatches when ON is selected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List / All Data.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Open Handle SW | Back door opener switch signal | ON or OFF | ON: Back door opener switch pushed
OFF: Back door opener switch not pushed |
- |
| Tester Display |
|---|
| Back Door Open Handle SW |
The GTS indicates ON or OFF according to the switch operation shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Remove the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL
Inspect the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U7-3 (UL) - G78-23 (BDSU) | Always | Below 1 Ω |
| U7-2 (E) - Body ground | ||
| U7-3 (UL) or G78-23 (BDSU) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Remove the back door lock assembly.
Inspect the back door lock assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3E instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U12-2 (ACT+) - 3E-8 (TR+) | Always | Below 1 Ω |
| U12-3 (D+) - 3E-33 (BCTY) | ||
| U12-1 (ACT-) - Body ground | ||
| U12-2 (ACT+) or 3E-8 (TR+) - Body ground | Always | 10 kΩ or higher |
| U12-3 (D+) or 3E-33 (BCTY) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check that the back door can be opened.
The back door can be opened.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL