Home › Engine / Hybrid System › 2AR-FE EMISSION CONTROL › CANISTER(w/ Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008398 2AR-FE EMISSION CONTROL _0055002 CANISTER(w/ Canister Pump Module) A

2AR-FE EMISSION CONTROL  CANISTER(w/ Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77740Q 1.INSTALL CANISTER PUMP MODULE

a.
A263356

Engage the 2 claws to install a new canister pump module to the charcoal canister assembly.

NOTICE:
·

Do not allow foreign matter such as grease, oil or water to adhere to the O-rings.


·

Ensure that the claws are engaged properly.




Hide 77765 2.INSTALL CHARCOAL CANISTER PROTECTOR

a.

Install the charcoal canister protector with the claw.


Hide 77751 3.INSTALL CHARCOAL CANISTER BASE BRACKET

a.

Install the charcoal canister base bracket with the claw.


Hide 77740 4.INSTALL CHARCOAL CANISTER ASSEMBLY

a.

Install the charcoal canister assembly with the 4 bolts and clip.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.
A299641C01
0.708,1.135 1.406,1.135 true 2.302,1.219 2.521,1.479 2.521,1.479 2.656,1.479 true 1.583,1.396 1.583,1.24 1.583,1.24 1.802,1.021 true 2.25,2.188 2.458,2.188 2.458,2.188 2.542,2.333 true 2.385,3.052 2.604,3.052 2.604,3.052 2.708,2.948 false 1.323,2.792 1.323,2.583 1.323,2.583 1.146,2.531 false 0.531,1.063 0.719,1.25 0.188,0.188 10 true *1 2.677,1.396 2.875,1.573 0.198,0.177 10 true *2 1.5,1.396 1.708,1.573 0.208,0.177 10 true *3 0.563,2.115 0.875,2.271 0.313,0.156 10 false *a 2.083,2.115 2.292,2.292 0.208,0.177 10 false *4 2.219,2.979 2.427,3.156 0.208,0.177 10 false *5 1.24,2.802 1.448,2.979 0.208,0.177 10 false *4
*1 Vent Line Hose
*2 Air Inlet Line Hose
*3 Purge Line Hose
*a Push


Connect the vent line hose.

i.

Push the hose into the port and push the retainer to lock it.

NOTICE:
·

Check for damage or foreign objects on the connected part.

·

After connecting the hose, check that the vent hose and valve are securely connected by pulling on them.





c.

Connect the air inlet hose.

i.

Check that the retainer is secured inside the housing.


ii.

Insert the air inlet hose straight into the pipe and push it in until a clicking sound is heard.

NOTICE:
·

Check for damage or foreign objects on the connected part.

·

After connecting the hose, check that the vent line hose and valve are securely connected by pulling on them.





d.

Connect the purge line hose, and slide the clamp to secure it.


e.

Connect the connector.


Hide 77641A 5.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector with the nut and 3 clips.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)