Home › Drivetrain › K111 MULTIDRIVE / CVT › REVOLUTION SENSOR
RM3090E _52 Drivetrain _008435 K111 MULTIDRIVE / CVT _0047074 REVOLUTION SENSOR G

K111 MULTIDRIVE / CVT  REVOLUTION SENSOR  INSPECTION  


PROCEDURE

Hide 89413B 1.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)

C200614C02
1.219,1.677 1.521,1.156 false 2.219,1.688 1.917,1.167 false 1,1.719 1.448,1.917 0.448,0.198 10 NIN+ 2.167,1.729 2.615,1.927 0.448,0.198 10 NIN- 0.229,0.156 0.542,0.354 0.313,0.198 10 *a
*a Component without harness connected
(Transmission Revolution Sensor (NIN))


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω


If the result is not as specified, replace the transmission revolution sensor (NIN).


Hide 89413B 2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

a.

Connect the battery to the sensor as shown in the illustration.


b.
C279306
0.833,0.656 1.479,0.656 false 1.865,0.719 2.521,0.708 false 0.875,2.479 1.375,2.469 false 0.271,2.292 0.542,2.292 false 0.542,0.573 0.969,0.906 0.427,0.333 10 NTB 0.156,0.083 0.469,0.354 0.313,0.271 10 *a 2.583,0.625 3.073,0.917 0.49,0.292 10 NTO 1.51,1.708 1.813,1.948 0.302,0.24 10 *2 1.552,4.052 1.865,4.25 0.313,0.198 10 *c 2.229,3.813 2.542,4.01 0.313,0.198 10 *2 1.427,2.406 1.594,2.615 0.167,0.208 10 1 0.156,2.208 0.406,2.448 0.25,0.24 10 2 2.333,2.354 2.646,2.552 0.313,0.198 10 *1 2.917,3.594 3.229,3.792 0.313,0.198 10 *b
*1 Battery
*2 Ammeter
*a Component without harness connected
(Transmission Revolution Sensor (NT))
*b Magnet
*c 5 mm gap or closer


Wave a magnetic object left and right in front of the tip of the transmission revolution sensor (5 mm (0.197 in.) gap or closer) to change the high/low signals while measuring the current.

NOTICE:

Be sure to wave a magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low Signal 4 to 8 mA
1 (NTO) - 2 (NTB) High Signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NT).


Hide 89413B 3.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

a.

Connect the battery to the sensor as shown in the illustration.


b.
C279306
0.833,0.656 1.479,0.656 false 1.865,0.719 2.521,0.708 false 0.875,2.479 1.375,2.469 false 0.271,2.292 0.542,2.292 false 0.542,0.573 0.969,0.906 0.427,0.333 10 NTB 0.156,0.083 0.469,0.354 0.313,0.271 10 *a 2.583,0.625 3.073,0.917 0.49,0.292 10 NTO 1.51,1.708 1.813,1.948 0.302,0.24 10 *2 1.49,4.094 1.802,4.292 0.313,0.198 10 *c 2.229,3.813 2.542,4.01 0.313,0.198 10 *2 1.427,2.406 1.594,2.615 0.167,0.208 10 1 0.156,2.208 0.406,2.448 0.25,0.24 10 2 2.323,2.365 2.635,2.563 0.313,0.198 10 *1 2.938,3.604 3.292,3.844 0.354,0.24 10 *b
*1 Battery
*2 Ammeter
*a Component without harness connected
(Transmission Revolution Sensor (NOUT))
*b Magnet
*c 5 mm gap or closer


Wave a magnetic object left and right in front of the tip of the transmission revolution sensor (5 mm (0.197 in.) gap or closer) to change the high/low signals while measuring the current.

NOTICE:

Be sure to wave a magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NOTO) - 2 (NOTB) Low Signal 4 to 8 mA
1 (NOTO) - 2 (NOTB) High Signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NOUT).