Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048750 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  U0073  Control Module Communication Bus OFF  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the ECM via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0073 Control Module Communication Bus OFF The condition that the bus OFF state occurs once or more within 0.1 seconds occurs 10 times in succession while the voltage at the IG1 terminal is between 10 and 17.4 V. (Sent signals cannot be received.) CAN communication system

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open ECM communication open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
EFI Communication Open
50003 105 204
HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
There is a constant open circuit
There are no momentary interruptions
There are momentary interruptions



There is a constant open circuit

2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED

There are no momentary interruptions

3.RECONFIRM DTC

There are momentary interruptions

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
a.

Turn the ignition switch off.


b.

Check if each sensor or ECM connector is securely connected.

OK:

Each connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Record the output DTCs (for ABS and CAN communication).

for ABS: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

for CAN communication system: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS) after the CAN communication system returns to normal.


Result:
Result Proceed to
DTC (relating to CAN communication system) is output A
DTC (relating to ABS) is output B
DTC is not output C




A

B

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the ignition switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


d.

Check that there is no momentary interruption.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the ignition switch off.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


e.

Check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSTIC TROUBLE CODE CHART


f.

If ABS DTCs are output, record them.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

HINT:

The CAN communication system must be normal when repairing each sensor DTC (for ABS).


Result:
Proceed to
DTC is not output
DTC is output (relating to ABS)
DTC is output (relating to CAN communication system)



DTC is not output

END

DTC is output (relating to ABS)

DTC is output (relating to CAN communication system)