Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM L

1AD-FTV ENGINE CONTROL  ECD SYSTEM  PRECAUTION  


IGNITION SWITCH EXPRESSION


HINT:

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



INITIALIZATION AND REGISTRATION


HINT:

When the ECM and other component(s) are replaced at the same time, perform the following utility items by following the instructions shown on the GTS display, starting with the ECM.

Replacement Part Utility Item
ECM
·

Learning Values Save

Click here(Click here)

·

Learning Values Write

Click here(Click here)


Engine assembly
·

Crank Time Compensation Reset

Click here(Click here)

·

Injector Compensation

Click here(Click here)

·

Pilot Quantity Learning

Click here(Click here)


No. 1 crankshaft position sensor plate Crank Time Compensation Reset
Click here(Click here)
Air fuel ratio sensor A/F Sensor Compensation Reset
Click here(Click here)
Supply pump assembly
Suction control valve
Supply Pump Initialization
Click here(Click here)
Exhaust manifold converter sub-assembly (DPF catalyst) Catalyst Record Clear
Click here(Click here)
Injector assembly
·

Injector Compensation

Click here(Click here)

·

After that perform the Pilot Quantity Learning

Click here(Click here)




HINT:

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initializations/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.



CATALYST RECORD OF DPF THERMAL DETERIORATION


HINT:

The ECM stores the history data of DPF catalyst thermal deterioration. This data is updated continuously and is then converted to an 8-digit code and is stored in the EEPROM. If the ECM determines that replacement of the DPF catalyst is required based on the thermal deterioration data, the DTC is stored to inform the driver.


a.

When only the DPF catalyst is replaced.

i.

After replacing the DPF catalyst, clear the thermal deterioration data stored in the ECM.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION



b.

When only the ECM is replaced.

i.

After replacing the ECM, input the original thermal deterioration data stored before replacement.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

NOTICE:
·

Read the thermal deterioration data stored in the ECM before replacement, and store the data in the GTS.

·

If the thermal deterioration data cannot be read, be sure to replace the DPF catalyst with a new one and initialize the ECM.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION





c.

After replacing both the DPF catalyst and the ECM, clear the thermal deterioration data stored in the new ECM.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION

HINT:

Clearing the thermal codes is required because initialization codes are stored in a new ECM. Failure to do this will cause a DTC to be stored.




INJECTOR COMPENSATION CODE


HINT:
·

Each injector assembly has different fuel injection characteristics. In order to optimize fuel injection performance, the ECM compensates for these differences by adjusting the fuel injection duration of each injector according to its compensation code. Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly.

·

If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



a.
A203986
1.49,2.573 2.583,2.083 false 0.167,0.125 0.479,0.323 0.313,0.198 10 *a 1.292,2.521 1.604,2.719 0.313,0.198 10 *1
*1 Injector Compensation Code
*a Example


When an injector assembly is replaced, the injector compensation code must be input into the ECM.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION



PILOT QUANTITY LEARNING


HINT:
·

By performing "Pilot Quantity Learning", the injection volume for each cylinder is precisely adjusted so that the engine runs smoothly. The "Pilot Quantity Learning" information is stored in the EEPROM of the ECM.

·

If an incorrect pilot quantity learning value is input into the ECM, the engine may rattle or engine idling may become rough.



a.

When an injector assembly is replaced, the injector compensation code must be input to the ECM and then pilot quantity learning must be performed.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

When the ECM is replaced, all of the existing injector pilot quantity learning values must be input into the new ECM.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION



DIFFICULT TO START ENGINE, ENGINE STALLING, BLACK SMOKE EMITTED ROUGH IDLING, EXCESSIVE ENGINE VIBRATION, ENGINE KNOCKING, LACK OF POWER OR HESITATION


a.

Check if the customer problem is described below. If so, refer to the appropriate troubleshooting section.

i.

Engine is difficult to start or stalls.


ii.

Black smoke is emitted.


iii.

Rough idling or excessive engine vibrations.


iv.

Engine knocking or rattling.


v.

Lack of power or hesitation.




WHEN USING GTS


CAUTION:

Observe the following items for safety reasons:

·

Before using the GTS, read the instruction manual.

·

Prevent the GTS cable from being caught on the pedals, shift lever or steering wheel when driving with the GTS connected to the vehicle.

·

When driving the vehicle for testing purposes using the GTS, two persons are required. One is for driving the vehicle, and the other operates the GTS.