Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM U

1AD-FTV ENGINE CONTROL  ECD SYSTEM  TERMINALS OF ECM  


CHECK ECM


A194498
2.521,0.24 2.917,0.479 0.396,0.24 5.521,0.24 5.917,0.479 0.396,0.24 2.594,0.302 2.875,0.458 0.281,0.156 10 B76 5.604,0.292 5.885,0.438 0.281,0.146 10 A61

a.

Measure the voltage, resistance or waveform of the ECM connector.

HINT:

The standard voltage, resistance and waveform of each ECM terminal is shown in the table below.

In the table, first follow the information in "Condition". Look at "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage, resistance and waveform between the terminals is shown in "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A61-1 (+B) - B76-109 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
A61-2 (BATT) - B76-109 (E1) W - BR Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
A61-4 (CANN) - B76-109 (E1) W - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 1)
A61-5 (CANP) - B76-109 (E1) B - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
A61-6 (CANL) - B76-109 (E1) W - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 1)
A61-7 (CANH) - B76-109 (E1) Y - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
A61-12 (W) - B76-109 (E1) R - BR MIL MIL illuminated Below 3 V
MIL not illuminated 11 to 14 V
A61-13 (TACH) - B76-109 (E1) GR - BR Engine speed Idling Pulse generation
(See waveform 3)
A61-14 (SPD) - B76-109 (E1) V - BR Speed signal from combination meter Ignition switch ON, drive wheels rotating slowly Pulse generation
(See waveform 4)
A61-20 (+B2) - B76-109 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
A61-21 (FANH) - B76-109 (E1) W - BR FAN NO. 1, 2 relay Idling with high engine coolant temperature Below 1.5 V
A61-22 (FANL) - B76-109 (E1) R - BR FAN NO. 3 relay Ignition switch ON 11 to 14 V
Idling with A/C on
or high engine coolant temperature
Below 1.5 V
A61-25 (IGSW) - B76-109 (E1) B - BR Ignition switch Ignition switch ON 11 to 14 V
A61-26 (TC) - B76-109 (E1) G - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A61-34 (ST1-) - B76-109 (E1) GR - BR Stop light switch assembly Ignition switch ON, brake pedal depressed Below 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A61-35 (STP) - B76-109 (E1) L - BR Stop light switch assembly Ignition switch ON, brake pedal depressed 7.5 to 14 V
Ignition switch ON, brake pedal released Below 1.5 V
A61-43 (STA) - B76-109 (E1) SB - BR Starter signal Cranking 5.5 V or higher
A61-44 (IREL) - B76-109 (E1) R - BR EDU relay Idling 0 to 1.5 V
A61-45 (MREL) - B76-109 (E1) B - BR EFI-MAIN relay Ignition switch ON 11 to 14 V
2 seconds elapsed since ignition switch off 0 to 1.5 V
A61-53 (VPA) - A61-56 (EPA) Y - W Accelerator pedal sensor assembly (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
A61-54 (VPA2) - A61-58 (EPA2) P - R Accelerator pedal sensor assembly (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 4.75 V
A61-55 (VCPA) - A61-56 (EPA) B - W Power source of accelerator pedal sensor assembly (for VPA1) Ignition switch ON 4.5 to 5.5 V
A61-57 (VCP2) - A61-58 (EPA2) L - R Power source of accelerator pedal sensor assembly (for VPA2) Ignition switch ON 4.5 to 5.5 V
A61-10 (NEO) - B76-109 (E1) P - BR Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 5)
B76-57 (GLDO) - B76-109 (E1) L - BR Glow plug controller Glow plug on Pulse generation
B76-41 (PCV+) - B76-81 (PCV-) LG - R Suction control valve Idling or cranking with warm engine Pulse generation
(See waveform 6)
B76-42 (M+) - B76-84 (ME01) V - W-B Throttle valve duty signal Engine warmed up, engine racing Pulse generation
B76-43 (M-) - B76-84 (ME01) P - W-B Throttle valve duty signal Engine warmed up, engine racing Pulse generation
B76-44 (E02) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
B76-45 (E01) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
B76-46 (E05) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
B76-47 (#4) - B76-109 (E1) L - BR Injector assembly Idling Pulse generation
(See waveform 7)
B76-48 (#3) - B76-109 (E1) LG - BR
B76-49 (#2) - B76-109 (E1) G - BR
B76-50 (#1) - B76-109 (E1) GR - BR
B76-51 (INJF) - B76-109 (E1) P - BR Injector driver (EDU) Idling Pulse generation
(See waveform 8)
B76-52 (PRD) - B76-109 (E1) B - BR Pressure discharge valve drive signal Engine warmed up, engine racing Pulse generation
(See waveform 9)
B76-56 (GLDI) - B76-109 (E1) G - BR Glow plug controller Glow plug on Pulse generation
B76-58 (GREL) - B76-109 (E1) B - BR Glow plug relay assembly Ignition switch ON 11 to 14 V
B76-62 (IDLO) - B76-109 (E1) Y - BR Injector driver (EDU) Idling 4 to 5.5 V
B76-65 (VG) - B76-64 (EVG) R - G Mass air flow meter assembly power source Ignition switch ON Pulse generation
B76-66 (PCR1) - B76-67 (E2M) P - BR Fuel pressure sensor (main) Idling 1.8 to 2.1 V
B76-68 (VCM) - B76-67 (E2M) V - BR Power source of fuel pressure sensor (for PCR1) Ignition switch ON 4.5 to 5.5 V
B76-69 (VCS) - B76-91 (E2S) R - L Power source of fuel pressure sensor (for PCR2) Ignition switch ON 4.5 to 5.5 V
B76-75 (VCPM) - B76-72 (EPIM) V - BR Power source of manifold absolute pressure sensor Ignition switch ON 4.5 to 5.5 V
B76-75 (VCPM) - B76-74 (EPEX) V - BR Power source of differential pressure sensor assembly Ignition switch ON 4.5 to 5.5 V
B76-76 (THCF) - B76-77 (ETCF) L - W Exhaust gas temperature sensor Engine warmed up, idling 4.6 to 4.9 V
B76-78 (VCG) - B76-109 (E1) B - BR Power source of camshaft position sensor Ignition switch ON 4.5 to 5.5 V
B76-80 (G2+) - B76-79 (G2-) G - W Camshaft position sensor Idling Pulse generation
(See waveform 10)
B76-82 (GE01) - Body ground BR - - Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω
B76-83 (EOPV) - B76-109 (E1) G - BR Oil pressure switching valve assembly Idling Below 1.5 V
B76-85 (EGM-) - B76-84 (ME01) B - W-B Electric EGR control valve assembly duty signal Engine warmed up, idling Pulse generation
B76-86 (EGM+) - B76-84 (ME01) W - W-B Electric EGR control valve assembly duty signal Engine warmed up, idling Pulse generation
B76-93 (VPOP) - B76-70 (EPOP) V - BR Power source of oil pressure sender gauge assembly Ignition switch ON 4.5 to 5.5 V
B76-94 (VCEG) - B76-95 (EEGL) W - BR EGR valve position sensor Ignition switch ON 4.5 to 5.5 V
B76-97 (VCVL) - B76-96 (EVLU) W - BR Throttle position sensor Ignition switch ON 4.98 to 5.02 V
B76-98 (PEX) - B76-74 (EPEX) P - BR Differential pressure sensor assembly Ignition switch ON 0.4 to 4.8 V
B76-101 (VNVC) - B76-100 (VNE2) G - L Power source of nozzle vane position sensor Ignition switch ON 4.5 to 5.5 V
B76-103 (NE+) - B76-102 (NE-) W - B Crankshaft position sensor Idling Pulse generation
(See waveform 10)
B76-104 (HAF2) - B76-46 (E05) L - W-B Air fuel ratio sensor heater Ignition switch ON 11 to 14 V
B76-105 (FIV) - B76-109 (E1) GR - BR Exhaust fuel addition injector assembly Engine warmed up, idling, every 1 to 2 minutes Pulse generation
B76-106 (ECBV) - B76-109 (E1) Y - BR No. 1 vacuum switching valve assembly (for EGR cooler) No. 1 vacuum switching valve assembly (for EGR cooler) on Below 1.5 V
No. 1 vacuum switching valve assembly (for EGR cooler) off 11 to 14 V
B76-107 (M-) - B76-109 (E1) W - BR DC motor (turbocharger sub-assembly) Idling with warm engine Pulse generation
(See waveform 11)
B76-108 (M+) - B76-109 (E1) B - BR DC motor (turbocharger sub-assembly) Idling with warm engine Pulse generation
(See waveform 11)
B76-109 (E1) - Body ground BR - - Earth (ground) circuit of ECM Always Below 1 Ω
B76-110 (THA) - B76-87 (ETHA) W - BR Intake air temperature sensor Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
B76-111 (THW) - B76-88 (ETHW) B - BR Engine coolant temperature sensor Idling, engine coolant temperature 60 to 120°C (140 to 248°F) 0.2 to 1.0 V
B76-112 (THF) - B76-89 (ETHF) GR - BR Fuel temperature sensor Ignition switch ON 0.5 to 3.4 V
B76-113 (THIA) - B76-90 (ETHI) Y - BR Intake air temperature sensor (turbo) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
B76-114 (PCR2) - B76-91 (E2S) W - L Fuel pressure sensor (sub) Idling 1.2 to 1.5 V
B76-116 (POP) - B76-70 (EPOP) R - BR Oil pressure sender gauge assembly Idling 0.1 to 0.9 V
B76-117 (PIM) - B76-72 (EPIM) G - BR Manifold absolute pressure sensor Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied 0.3 to 0.9 V
Atmospheric pressure 0.8 to 1.4 V
Positive pressure of 69 kPa (518 mmHg, 20.3 in.Hg) applied 1.6 to 2.2 V
B76-118 (EGLS) - B76-95 (EEGL) GR - BR EGR valve position sensor Ignition switch ON 1.03 to 1.37 V
B76-119 (VLU) - B76-96 (EVLU) G - BR Throttle position sensor Ignition switch ON, throttle valve fully opened 3.6 to 4.2 V
B76-121 (THCO) - B76-120 (ETCO) P - BR No. 3 Exhaust gas temperature sensor Engine warmed up, idling 4.6 to 4.9 V
B76-122 (THCI) - B76-99 (ETCI) L - BR No. 2 Exhaust gas temperature sensor Engine warmed up, idling 4.6 to 4.9 V
B76-123 (RLFF) - B76-109 (E1) V - BR Pressure discharge valve confirmation signal Engine warmed up, engine racing Pulse generation
(See waveform 9)
B76-124 (VNA) - B76-100 (VNE2) R - L Nozzle vane position sensor Ignition switch ON 2.3 to 2.7 V
B76-125 (AF2+) - B76-46 (E05) L - W-B Air fuel ratio sensor Ignition switch ON 2.0 to 2.5 V
B76-126 (AF2-) - B76-46 (E05) Y - W-B Air fuel ratio sensor Ignition switch ON 2.0 to 2.5 V


b.
A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

Using an oscilloscope, check waveform 1.

Waveform 1:

CAN Communication Signal

ECM Terminal Name Between CANL and E1
Between CANN and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON


HINT:

The waveform varies depending on the CAN communication signal.



c.
A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

Using an oscilloscope, check waveform 2.

Waveform 2:

CAN Communication Signal

ECM Terminal Name Between CANH and E1
Between CANP and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON


HINT:

The waveform varies depending on the CAN communication signal.



d.
A283574E01
0.438,0.313 1.167,0.625 0.729,0.313 10 5 V/DIV. 0.448,1.177 0.896,1.458 0.448,0.281 10 GND 1.688,1.885 2.708,2.104 1.021,0.219 10 10 ms./DIV.

Using an oscilloscope, check waveform 3.

Waveform 3:

Engine Speed Signal

ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling


HINT:

The wavelength becomes shorter as the engine speed increases.



e.
A283573E01
2.677,0.125 3.354,0.385 0.677,0.26 10 5 V/DIV. 2.833,1.229 3.25,1.531 0.417,0.302 10 GND 1.156,1.99 2.219,2.167 1.063,0.177 10 20 ms./DIV.

Using an oscilloscope, check waveform 4.

waveform 4:

Vehicle Speed Signal

ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, driving wheels rotating slowly


HINT:

The wavelength becomes shorter as the vehicle speed increases.



f.
A287796E03
2.594,1.635 3.052,1.833 0.458,0.198 10 GND 2.406,0.104 3.052,0.313 0.646,0.208 10 1 V/DIV. 1.198,1.938 1.917,2.115 0.719,0.177 10 2 ms./DIV.

Using an oscilloscope, check waveform 5.

waveform 5:

Engine Speed Signal

ECM Terminal Name Between NEO and E1
Tester Range 1 V/DIV., 2 ms./DIV.
Condition Idling with warm engine


HINT:

The waveform varies depending on the engine speed.



g.
A294242
0.115,1.229 0.573,1.427 0.458,0.198 10 GND 2.542,0.094 3.281,0.26 0.74,0.167 10 10 V/DIV. 1.365,1.906 2.104,2.073 0.74,0.167 10 5 ms./DIV.

Using an oscilloscope, check waveform 6.

Waveform 6:

Suction Control Valve Signal

ECM Terminal Name Between PCV+ and PCV-
Tester Range 10 V/DIV., 5 ms./DIV.
Condition Idling or cranking with warm engine


HINT:

The waveform varies depending on the suction control valve operation.



h.
A208447
2.729,0.146 3.302,0.313 0.573,0.167 10 5 V/DIV. 0.177,0.406 0.573,0.573 0.396,0.167 10 (a) #1 0.177,0.792 0.573,0.958 0.396,0.167 10 (b) #3 0.177,1.177 0.573,1.344 0.396,0.167 10 (c) #4 0.177,1.573 0.573,1.74 0.396,0.167 10 (d) #2 1.5,1.844 2.469,2.01 0.969,0.167 10 20 ms./DIV.

Using an oscilloscope, check waveform 7.

Waveform 7:

No. 1 Injector Assembly Injection Signal

No. 2 Injector Assembly Injection Signal

No. 3 Injector Assembly Injection Signal

No. 4 Injector Assembly Injection Signal

ECM Terminal Name (a) Between #1 and E1
(b) Between #3 and E1
(c) Between #4 and E1
(d) Between #2 and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


HINT:

The waveform varies depending on the injector injection.



i.
A208448
2.688,0.25 3.26,0.417 0.573,0.167 10 2 V/DIV. 1.594,1.802 2.563,1.969 0.969,0.167 10 20 ms./DIV.

Using an oscilloscope, check waveform 8.

Waveform 8:

Injector Injection Confirmation Signal

ECM Terminal Name Between INJF and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling


HINT:

The waveform varies depending on the injector injection.



j.
A243948
0.229,0.948 0.823,1.188 0.594,0.24 10 (b) RLFF 0.313,2.208 0.833,2.448 0.521,0.24 10 (a) PRD 1.646,2.75 2.5,2.99 0.854,0.24 10 1 ms./DIV. 2.719,0.24 3.271,0.479 0.552,0.24 10 2 V/DIV.

Using an oscilloscope, check waveform 9.

Waveform 9:

Pressure Discharge Valve Drive Signal and Pressure Discharge Confirmation Signal

ECM Terminal Name (a) Between PRD and E1
(b) Between RLFF and E1
Tester Range 2 V/DIV., 1 ms./DIV.
Condition Engine warmed up, engine racing


HINT:

The waveform becomes shorter as the engine speed.



k.
A268870
2.677,0.073 3.25,0.24 0.573,0.167 10 5 V/DIV. 0.063,0.531 0.51,0.698 0.448,0.167 10 (a) NE 0.135,1.167 0.531,1.333 0.396,0.167 10 (b) G 1.302,1.802 2.125,2.042 0.823,0.24 10 20 ms./DIV. 2.958,0.563 3.313,0.729 0.354,0.167 10 GND 2.958,1.271 3.313,1.438 0.354,0.167 10 GND

Using an oscilloscope, check waveform 10.

Waveform 10:

Crankshaft Position Sensor and Camshaft Position Sensor Signal

ECM Terminal Name (a) Between NE+ and NE-
(b) Between G2+ and G2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


HINT:

The waveform varies depending on the engine speed.



l.
A148021
2.688,0.25 3.229,0.396 0.542,0.146 10 5 V/DIV. 1.229,1.875 2.167,2.104 0.938,0.229 10 50 ms./ DIV.

Using an oscilloscope, check waveform 11.

Waveform 11:

DC Motor Positive Terminal and DC Motor Negative Terminal

ECM Terminal Name Between M+ and E1
Between M- and E1
Tester Range 5 V/DIV., 50 ms./DIV.
Condition Idling with warm engine


HINT:

The waveform varies depending on turbocharger sub-assembly operation.