Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM U

1AD-FTV ENGINE CONTROL  ECD SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE CHART


If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.

HINT:

PM regeneration may be prohibited depending on the malfunctioning part of the exhaust treatment system (DPF related portion).


DTC No. Detection Item Fail-safe Operation Fail-safe Deactivation Condition
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) ECM turns off air fuel ratio sensor heater Ignition switch off
EGR learning is stopped. Pass condition detected
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) ECM turns off air fuel ratio sensor heater Ignition switch off
EGR learning is stopped. Pass condition detected
P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance The engine power is limited. Ignition switch off
P0047 Turbocharger/ Supercharger Boost Control "A" Circuit Low The engine power is limited. Ignition switch off
P0048 Turbocharger/ Supercharger Boost Control "A" Circuit High The engine power is limited. Ignition switch off
P007C Charge Air Cooler Temperature Sensor Circuit Low The intake air temperature is fixed at a specified value. Pass condition detected
P007D Charge Air Cooler Temperature Sensor Circuit High The intake air temperature is fixed at a specified value. Pass condition detected
P0087 Fuel Rail / System Pressure - Too Low The engine power is reduced by 90%.* Ignition switch off
P0088 Fuel Rail / System Pressure - Too High The engine power is reduced by 90%.* Ignition switch off
P0093 Fuel System Leak Detected - Large Leak The engine power is reduced by 90%.* Ignition switch off
P0100 Mass Air Flow Circuit Malfunction The engine power is limited by approximately 50%. Pass condition detected
P0101 Mass or Volume Air Flow Circuit Range / Performance Problem The engine power is limited by approximately 50%. Ignition switch off
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
·

The turbo pressure is fixed at a specified value.

·

The engine power is limited by using a fuel injection amount that corresponds to no boost.


Pass condition detected
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input
·

The turbo pressure is fixed at a specified value.

·

The engine power is limited by using a fuel injection amount that corresponds to no boost.


Pass condition detected
P0112 Intake Air Temperature Circuit Low Input The intake air temperature value is fixed. Pass condition detected
P0113 Intake Air Temperature Circuit High Input The intake air temperature value is fixed. Pass condition detected
P0115 Engine Coolant Temperature Circuit The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). Pass condition detected
P0117 Engine Coolant Temperature Circuit Low Input The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). Pass condition detected
P0118 Engine Coolant Temperature Circuit High Input The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). Pass condition detected
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P0168 Fuel Temperature Too High The maximum common rail pressure and maximum injection volume are reduced. Pass condition detected
P0180 Fuel Temperature Sensor "A" Circuit The fuel temperature is fixed at a specified value. Pass condition detected
P0182 Fuel Temperature Sensor "A" Circuit Low Input The fuel temperature is fixed at a specified value. Pass condition detected
P0183 Fuel Temperature Sensor "A" Circuit High Input The fuel temperature is fixed at a specified value. Pass condition detected
P0190 Fuel Rail Pressure Sensor Circuit
·

The main and sub circuits of the fuel pressure sensor are malfunctioning:

·

The engine power is reduced by 90%.*


·

The main or sub circuit of the fuel pressure sensor is malfunctioning:

·

The engine power is limited.



Ignition switch off
P0191 Fuel Rail Pressure Sensor Circuit Range / Performance
·

The main and sub circuits of the fuel pressure sensor are malfunctioning:

·

The engine power is reduced by 90%.*


·

The main or sub circuit of the fuel pressure sensor is malfunctioning:

·

The engine power is limited.



Ignition switch off
P0192 Fuel Rail Pressure Sensor Circuit Low Input
·

The main and sub circuits of the fuel pressure sensor are malfunctioning:

·

The engine power is reduced by 90%.*


·

The main or sub circuit of the fuel pressure sensor is malfunctioning:

·

The engine power is limited.



Ignition switch off
P0193 Fuel Rail Pressure Sensor Circuit High Input
·

The main and sub circuits of the fuel pressure sensor are malfunctioning:

·

The engine power is reduced by 90%.*


·

The main or sub circuit of the fuel pressure sensor is malfunctioning:

·

The engine power is limited.



Ignition switch off
P0201 Injector Circuit / Open - (Cylinder 1) The engine power is limited. Ignition switch off to ON or STA on
P0202 Injector Circuit / Open - (Cylinder 2) The engine power is limited. Ignition switch off to ON or STA on
P0203 Injector Circuit / Open - (Cylinder 3) The engine power is limited. Ignition switch off to ON or STA on
P0204 Injector Circuit / Open - (Cylinder 4) The engine power is limited. Ignition switch off to ON or STA on
P0299 Turbocharger / Supercharger Underboost The engine power is limited. Pass condition detected
P0335 Crankshaft Position Sensor "A" Circuit The engine power is reduced by 90%.* Pass condition detected
P0339 Crankshaft Position Sensor "A" Circuit Intermittent The engine power is reduced by 90%.* Pass condition detected
P0340 Camshaft Position Sensor Circuit Malfunction The engine power is reduced by 90%.* Pass condition detected
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) The engine power is reduced by 90%.* Pass condition detected
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) The engine power is reduced by 90%.* Pass condition detected
P0400 Exhaust Gas Recirculation Flow The engine power is limited. Ignition switch off
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low The engine power is limited. Ignition switch off
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High The engine power is limited. Ignition switch off
P042E Exhaust Gas Recirculation "A" Control Stuck Open The engine power is limited. Ignition switch off
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance The engine power is limited. Ignition switch off
P0489 Exhaust Gas Recirculation Control Circuit Low The engine power is limited. Ignition switch off
P0490 Exhaust Gas Recirculation Control Circuit High The engine power is limited. Ignition switch off
P0500 Vehicle Speed Sensor "A" The vehicle speed is fixed at 0 km/h (0 mph). Pass condition detected
P0522 Engine Oil Pressure Sensor / Switch Low The oil pressure is maintained at a normal oil pressure
(high oil pressure control mode).
Pass condition detected
P0523 Engine Oil Pressure Sensor / Switch High The oil pressure is maintained at a normal oil pressure
(high oil pressure control mode).
Pass condition detected
P0524 Engine Oil Pressure Too Low
·

The oil pressure is maintained at a normal oil pressure

(high oil pressure control mode).

·

The maximum injection volume is reduced.


Pass condition detected
P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1) The exhaust gas temperature is fixed at a specified value. Ignition switch off
P0546 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1) The exhaust gas temperature is fixed at a specified value. Ignition switch off
P0606 ECM / PCM Processor The engine power is reduced by 90%.* Pass condition detected
P060A Internal Control Module Monitoring Processor Performance The engine power is reduced by 90%.* Pass condition detected
P060B Internal Control Module A/D Processing Performance The engine power is reduced by 90%.* Pass condition detected
P0627 Fuel Pump Control Circuit / Open The engine power is limited. Pass condition detected
P062D No. 1 Fuel Injector Driver Circuit Performance
·

1 malfunctioning cylinder detected:

·

The engine power is limited.



·

2 or more malfunctioning cylinders detected:

·

Stalls the engine.



Ignition switch off
P06DB Engine Oil Pressure Control Circuit Low The oil pressure is maintained at a normal oil pressure
(high oil pressure control mode).
Pass condition detected
P06DC Engine Oil Pressure Control Circuit High The oil pressure is maintained at a normal oil pressure
(high oil pressure control mode).
Pass condition detected
P1229 Fuel Pump System The engine power is limited. Ignition switch off
P1251 Turbocharger / Supercharger Overboost Condition (Too High) The engine power is limited. Ignition switch off
P1271 Fuel Regulator Circuit Malfunction (EDU Drive) The engine power is limited. Ignition switch off
P1272 Fuel Pressure Regulator Malfunction The engine power is limited. Ignition switch off
P1626 Idle Signal Output Value Too Low The engine power is limited. Ignition switch off
P1627 Idle Signal Output Value Too High The engine power is limited. Ignition switch off
P200C Diesel Particulate Filter Over Temperature Bank 1 PM forced regeneration is prohibited. Ignition switch off
P200E Catalyst System Temperature Too High Bank 1 PM forced regeneration is prohibited. Ignition switch off
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2) The exhaust gas temperature is fixed at a specified value. Pass condition detected
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2) The exhaust gas temperature is fixed at a specified value. Pass condition detected
P2084 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 PM forced regeneration is prohibited. Pass condition detected
P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit
·

The engine power is reduced by 90%.*

·

PM forced regeneration is prohibited.


Pass condition detected
P20CF Exhaust Aftertreatment Fuel Injector "A" Stuck Open The engine power is reduced by 90%.* Pass condition detected
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P2138 Throttle / Pedal Position Sensor / Switch "D"/"E" Voltage Correlation The engine power is limited to an amount which allows the vehicle to be driven to a safe area. Ignition switch off
P2141 Diesel Throttle Motor Circuit Low The engine power is limited. Ignition switch off
P2142 Diesel Throttle Motor Circuit High The engine power is limited. Ignition switch off
P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2226 Barometric Pressure Circuit The atmospheric pressure is fixed at a specified value. Pass condition detected
P2228 Barometric Pressure Circuit Low Input The atmospheric pressure is fixed at a specified value. Pass condition detected
P2229 Barometric Pressure Circuit High Input The atmospheric pressure is fixed at a specified value. Pass condition detected
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2428 Exhaust Gas Temperature Too High Bank 1 PM forced regeneration is prohibited. Ignition switch off
P242B Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P242C Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P242D Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P244A Diesel Particulate Filter Differential Pressure Too Low PM forced regeneration is prohibited. Ignition switch off
P244B Diesel Particulate Filter Differential Pressure Too High The engine power is limited. Ignition switch off
P244C Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 1 PM forced regeneration is prohibited. Ignition switch off
P2453 Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance PM forced regeneration is prohibited. Pass condition detected
P2454 Diesel Particulate Filter Pressure Sensor "A" Circuit Low PM forced regeneration is prohibited. Pass condition detected
P2455 Diesel Particulate Filter Pressure Sensor "A" Circuit High PM forced regeneration is prohibited. Pass condition detected
P2463 Diesel Particulate Filter Restriction - Soot Accumulation The engine power is limited. Repair is complete
P2564 Turbocharger/ Supercharger Boost Control Position Sensor "A" Circuit Low The engine power is limited. Ignition switch off
P2565 Turbocharger/ Supercharger Boost Control Position Sensor "A" Circuit High The engine power is limited. Ignition switch off

HINT:

*: Engine power is limited immediately after the DTC is stored.