Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0116  Engine Coolant Temperature Circuit Range / Performance Problem  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor.

The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0116 Engine Coolant Temperature Circuit Range / Performance Problem Either of the following conditions is met (2 trip detection logic):
·

When engine is started cold and warmed up, the engine coolant temperature sensor value does not change.

·

After the warmed up engine is stopped and the next cold engine start is performed, the engine coolant temperature sensor value does not change.


·

Thermostat

·

Engine coolant temperature sensor


Comes on DTC stored

Related Data List
DTC No. Data List
P0116 Coolant Temp

HINT:

If DTC P0116 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0116 With the engine coolant temperature below 60°C (140°F), start the engine and idle it for 5 minutes. Then drive the vehicle at a speed of 40 km/h (25 mph) or more for a total of 5 minutes or more and check that the engine coolant temperature changes by 1°C (1.8°F) or higher.

MONITOR DESCRIPTION

Engine coolant temperature sensor cold start monitor

When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


Engine coolant temperature sensor soak monitor

If the engine coolant temperature sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0116 is output A
DTC P0116 and other DTCs are output B


HINT:

If any DTCs other than P0116 are output, troubleshoot those DTCs first.




A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT

Result:
Proceed to
OK
NG



OK

3.REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

4.REPLACE THERMOSTAT
3.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE THERMOSTAT
a.

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

d.

Check that the engine coolant temperature is 60°C (140°F) or less.


e.

Start the engine.


f.

Idle the engine for 5 minutes, and then drive the vehicle at a speed of 40 km/h (25 mph) or more for a total of 5 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



g.

Check that the engine coolant temperature changes by 1°C (1.8°F) or higher.


Result:
Proceed to
NEXT



NEXT

END