This DTC is stored when the speed of a specific cylinder becomes low and the idle speed becomes unstable. This DTC is also stored if the vehicle runs out of fuel. Be sure to check whether there is enough fuel in the fuel tank before inspection.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1605 | Rough Idling | When the accelerator pedal is fully closed and the engine is idling, the speed of a specific cylinder is low for 2 to 10 seconds (1 trip detection logic). | ·
Injector assembly ·
Injector compensation code ·
Fuel leak ·
Glow system ·
Intake system leakage ·
Intake system blockage ·
EGR system ·
Throttle valve system ·
Suction control valve ·
Low quality fuel ·
Fuel filter element assembly air bleed problem ·
Accessory problem (A/C, generator, etc.) ·
Engine assembly ·
ECM |
Does not come on | DTC stored |
| DTC No. | Data List |
|---|---|
| P1605 | ·
Target Idle Engine Speed ·
Engine Speed ·
MAP ·
MAF ·
Coolant Temp ·
Battery Voltage ·
Engine Speed of Cyl #1 (to #4) ·
Intake Air ·
Target Common Rail Pressure ·
Fuel Press ·
Common Rail Pres Sens 2 ·
Target Pump SCV Current ·
Injection Feedback Val #1 (to #4) ·
Injection Volume ·
Actual Throttle Position ·
Target EGR Position ·
Actual EGR Valve Pos. ·
EGR Close Lrn. Status ·
EGR Close Lrn. Val. ·
Glow Control Unit Duty |
In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1605 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as rough idling.
As the DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.
If any other DTCs are output, perform troubleshooting for those DTCs first.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.
In order for idling to be stable, glow system operation, fuel system operation and compression sufficient to maintain the target idling speed are necessary.
Glow system
The following malfunctions may be present in the glow system.
Engine coolant temperature sensor malfunction.
Glow plug assembly malfunction.
Glow plug controller malfunction.
Fuel system
The following malfunctions may be present in the fuel system.
Fuel leakage.
Problem with injector assemblies.
Problem with supply pump assembly.
Air in fuel pipe.
Engine assembly
The following malfunctions may be present in the engine assembly.
Insufficient compression.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Record the stored DTCs and freeze frame data.
This freeze frame data shows the actual engine conditions when the engine idling problem occurred.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P1605 is output | A |
| DTC P1605 and other DTCs are output | B |
If any DTCs other than DTC P1605 are output, troubleshoot those DTCs first.
A
B
Determine the cause of the problem based on the freeze frame data recorded in Procedure 1.
| Judgment of Data List Values | Problem Cause | Diagnosis Note |
|---|---|---|
| Rough Idle #1 to #4 in the freeze frame data is ON | Injector assembly | If the cylinder that displays Rough Idle ON also has a value of more than 3.0 mm3/st for Injection Feedback Val, improper combustion in that cylinder is suspected.
|
| Judgment of Data List Values | Problem Cause | Diagnosis Note |
|---|---|---|
| Injection Feedback Val #1 to #4 in the freeze frame data is higher than 3.0 mm3/st | Injector assembly | If the cylinder that displays Rough Idle ON also has a value of higher than 3.0 mm3/st for Injection Feedback Val, improper combustion in that cylinder is suspected. |
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>Rough Idling or Excessive Engine Vibrations