Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  


DESCRIPTION

HINT:

For more information on the injector assemblies and common rail system, refer to System Description (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).


The ECM detects combustion deterioration for a specific cylinder.

A113716C01
0.234,0.164 0.494,0.34 0.26,0.176 10 *a 2.79,1.168 2.951,1.338 0.161,0.17 10 *1 4.235,2.416 4.399,2.586 0.164,0.17 10 *4 2.809,3.156 2.975,3.327 0.166,0.17 10 *5 4.235,1.739 4.404,1.909 0.169,0.17 10 *2 2.754,1.951 2.92,2.121 0.166,0.17 10 *3 3.607,1.453 3.002,1.236 false 3.567,2.026 4.172,1.81 false 3.567,2.698 4.172,2.481 false 3.558,2.244 2.954,2.027 false 3.607,3.457 3.002,3.24 false
*1 Piezo Actuator *2 No. 1 Piston
*3 No. 2 Piston *4 Three-Way Valve
*5 Nozzle Needle - -
*a Injector Assembly Cross Section Diagram - -


HINT:
·

The cylinder which has the compensation value, indicated by Injection Feedback Val #1, #2, #3 and #4, that varies from the other cylinders may be malfunctioning.

·

If DTC P0093 (fuel leaks from high-pressure area) is stored simultaneously, a leakage malfunction of a specific cylinder has probably occurred.

·

If DTC P0201, P0202, P0203, P0204 and/or P062D (open or short in the injector driver or injector circuit) is stored simultaneously, there is probably a faulty circuit located between the ECM and the injector assembly including the injector driver.

·

If only DTC P0301, P0302, P0303 and/or P0304 (injector malfunction) has been stored, an injector assembly mechanical malfunction or insufficient compression (valve clearance, etc.) has probably occurred. An open or short malfunction of the ECM, injector driver or injector circuit is unlikely.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0301 Cylinder 1 Misfire Detected Injector Feedback Val #1 is 5.0 mm3/st and the engine speed fluctuation of No. 1 cylinder is large during idling.
(2 trip detection logic)
Main Trouble Area
·

No. 1 Injector assembly

·

Compression pressure


Related Trouble Area
·

Valve timing

·

Fuel with low cetane number used

·

ECM


Comes on DTC stored
P0302 Cylinder 2 Misfire Detected Injector Feedback Val #2 is 5.0 mm3/st and the engine speed fluctuation of No. 2 cylinder is large during idling.
(2 trip detection logic)
Main Trouble Area
·

No. 2 Injector assembly

·

Compression pressure


Related Trouble Area
·

Valve timing

·

Fuel with low cetane number used

·

ECM


Comes on DTC stored
P0303 Cylinder 3 Misfire Detected Injector Feedback Val #3 is 5.0 mm3/st and the engine speed fluctuation of No. 3 cylinder is large during idling.
(2 trip detection logic)
Main Trouble Area
·

No. 3 Injector assembly

·

Compression pressure


Related Trouble Area
·

Valve timing

·

Fuel with low cetane number used

·

ECM


Comes on DTC stored
P0304 Cylinder 4 Misfire Detected Injector Feedback Val #4 is 5.0 mm3/st and the engine speed fluctuation of No. 4 cylinder is large during idling.
(2 trip detection logic)
Main Trouble Area
·

No. 4 Injector assembly

·

Compression pressure


Related Trouble Area
·

Valve timing

·

Fuel with low cetane number used

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0301
P0302
P0303
P0304
·

Injection Volume

·

Injection Feedback Val #1 to #4

·

Fuel Press

·

Target Common Rail Pressure



HINT:
·

If DTC P0301, P0302, P0303 or P0304 is stored, the following symptoms may appear:

·

Rough idle

·

Poor driveability


·

After confirming DTC P0301, P0302, P0303 or P0304, check the internal fuel pressure on the GTS by entering the following menus: Powertrain / Engine / Data List / Fuel Press, Target Common Rail Pressure.

Under a stable condition such as idling or running the engine at 2500 rpm without load, Fuel Press is within 5000 kPa of Target Common Rail Pressure.



MONITOR DESCRIPTION

P0301, P0302, P0303 or P0304 (Injection malfunction, except open or short in injector circuit):

This DTC will be stored if the engine speed fluctuation between each cylinder is large. The ECM monitors changes in the crankshaft rotation speed using the crankshaft position sensor in order to detect improper combustion. The camshaft position sensor also plays a role in determining which cylinder has the problem. The fluctuation counter increases when irregular crankshaft rotation speed variation exceeds the threshold with the engine idling. Therefore, if any one of the cylinders is operating poorly (rough idle), the ECM stores this DTC.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0301 Warm up the engine and idle it for 60 seconds
P0302
P0303
P0304

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing the fuel supply pump assembly, the ECM needs initialization (Click here ).Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION

·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When this DTC is stored, be sure to carefully examine "Injection Feedback Val #1 to #4", "Injection Volume", "Fuel Press", "Target Common Rail Pressure", "Engine Speed", "MAF", "Coolant Temp" and "Vehicle Speed" in the freeze frame data.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0301, P0302, P0303 OR P0304)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC P0301, P0302, P0303 or P0304 is output
DTC P0301, P0302, P0303 or P0304 and other DTCs are output


HINT:
·

If any DTCs other than P0301, P0302, P0303 or P0304 are output, troubleshoot those DTCs first.

·

If DTCs other than P0301, P0302, P0303 or P0304 are not output, check the fuel condition before proceeding to the next step.





DTC P0301, P0302, P0303 or P0304 is output

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)

DTC P0301, P0302, P0303 or P0304 and other DTCs are output

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)
a.

Check the wire harness and connector connections.

OK:

The wire harness and connectors have been connected securely and there are good connections.



Result:
Proceed to
OK
NG



OK

3.CHECK INJECTOR COMPENSATION CODE

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation codes.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

OK:

Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)

NG

9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
4.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Val #1 to #4.

Powertrain > Engine > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
50003 61 368,369,370,371

d.

Read the value.

Standard value:

The compensatory injection volume is less than 3.0 mm3/st


HINT:
·

If the fuel injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.

·

If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector assembly to inject.




e.

Inspect and repair the cylinder that has an improper compensation value according to the following steps.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut / #1 to #4.

Powertrain > Engine > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

d.

Check the 4 cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

6.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
6.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Engine > Active Test
Tester Display
Check the Cylinder Compression
50004 61 111

Result:
Proceed to
OK
NG



OK

7.REPLACE INJECTOR ASSEMBLY

NG

12.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
7.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Perform the pilot quantity learning.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0301, P0302, P0303 OR P0304)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0301, P0302, P0303 OR P0304)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine.


f.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0301, P0302, P0303 or P0304.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P0301, P0302, P0303 or P0304 is output A
All Readiness ABNORMAL A
NORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, increase the idling time.





A

11.REPLACE ECM

B

END

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine.


g.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


h.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0301, P0302, P0303 or P0304.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END