Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low EGR valve position sensor output voltage is less than 0.1 V for 5 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

EGR valve assembly (EGR valve position sensor)

·

ECM


Comes on DTC stored
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High EGR valve position sensor output voltage is higher than 4.9 V for 5 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

EGR valve assembly (EGR valve position sensor)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for higher than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0405 Ignition switch ON for 5 seconds or more
P0406

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (VC) - B76-94 (VCEG) Always Below 1 Ω
i1-4 (VTA) - B76-118 (EGLS) Always Below 1 Ω
i1-3 (E2) - B76-95 (EEGL) Always Below 1 Ω
i1-2 (VC) or B76-94 (VCEG) - Body ground Always 10 kΩ or higher
i1-4 (VTA) or B76-118 (EGLS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC EGR CONTROL VALVE ASSEMBLY)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.
A204592
0.271,0.698 0.667,0.948 0.396,0.25 0.896,1.833 1.406,1.313 true 2.302,1.823 1.74,1.271 true 0.198,0.135 0.375,0.313 0.177,0.177 10 false *a 2.271,1.854 2.542,2.042 0.271,0.188 10 false E2 0.771,1.885 1.073,2.063 0.302,0.177 10 false VC 0.396,0.74 0.729,0.896 0.333,0.156 10 false i1
*a Front view of wire harness connector
(to Electric EGR Valve Assembly)


Disconnect the electric EGR control valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
i1-2 (VC) - i1-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>EGR VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (P0405 OR P0406)
4.CHECK WHETHER DTC OUTPUT RECURS (P0405 OR P0406)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Turn the ignition switch to ON for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.

OK:

DTC is not output again.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Turn the ignition switch to ON for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END