| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0627 | Fuel Pump Control Circuit / Open | Even though the CPU (command area inside ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds.
(1 trip detection logic) |
·
Open or short in suction control valve circuit ·
Suction control valve ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0627 | Fuel Press
Target Common Rail Pressure |
For more information on the fuel supply pump (suction control valve) and common rail system, refer to the System Description (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).
When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine / Data List / Fuel Press.
Under a stable operating condition such as idling, Fuel Press is within +/-5000 kPa of Target Common Rail Pressure.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0627 | Idling for 1 second |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
After replacing the fuel supply pump, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *1 | Fuel Supply Pump |
| *a | Component without harness connected
(Suction Control Valve) |
Disconnect the suction control valve connector.
Measure the resistance according to the value(s) in the table below
No open or short circuit malfunction.
Reconnect the suction control valve connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B48-1 - B76-41 (PCV+) | Always | Below 1 Ω |
| B48-2 - B76-81 (PCV-) | Always | Below 1 Ω |
| B48-1 or B76-41 (PCV+) - Body ground | Always | 10 kΩ or higher |
| B48-2 or B76-81 (PCV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Proceed to |
|---|
| DTC is not output |
| DTC P0627 is output |
DTC is not output
DTC P0627 is output
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the suction control valve.
Click hereEngine / Hybrid System>2AD-FHV FUEL>SUCTION CONTROL VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Perform supply pump initialization.
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT