Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM J

2AD-FHV ENGINE CONTROL  ECD SYSTEM  Injector Circuit  


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INJECTOR DRIVER (EDU))
a.
A204910C02
0.49,1.021 0.896,1.281 0.406,0.26 1.958,0.958 2.458,0.698 true 1.948,1.406 2.354,1.615 true 2.521,0.604 2.813,0.823 0.292,0.219 10 +B 2.406,1.573 2.792,1.792 0.385,0.219 10 GND 0.229,0.208 0.406,0.365 0.177,0.156 10 *a 0.552,1.063 0.854,1.229 0.302,0.167 10 B51
*a Front view of wire harness connector
(to Injector Driver (EDU))


Disconnect the injector driver (EDU) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B51-2 (+B) - B51-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - BODY GROUND)
a.

Disconnect the injector driver (EDU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT EDU RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT EDU RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EDU RELAY)

NG

REPLACE EDU RELAY

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EDU RELAY)
a.
A298899
0.094,0.375 0.406,0.531 0.313,0.156 10 *1 2.021,1.115 2.333,1.271 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EDU Relay


Remove the EDU relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EDU relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - EDU RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EDU RELAY)

5.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - EDU RELAY)
a.

Disconnect the injector driver (EDU) connector.


b.

Remove the EDU relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-2 (+B) - 3 (EDU relay) Always Below 1 Ω
B51-2 (+B) or 3 (EDU relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM - EDU RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECM - EDU RELAY)
a.

Disconnect the ECM connector.


b.

Remove the EDU relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A61-44 (IREL) - 1 (EDU relay) Always Below 1 Ω
A61-44 (IREL) or 1 (EDU relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EDU RELAY - EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (EDU RELAY - EFI-MAIN NO. 2 RELAY)
a.

Remove the EDU relay and EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EDU relay) - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
2 (EDU relay) or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT EFI-MAIN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT EFI-MAIN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)
a.
A298897
0.063,0.052 0.375,0.208 0.313,0.156 10 *1 1.896,0.531 2.208,0.688 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 2 relay


Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

10.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ECM - EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ECM - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the ECM connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A61-45 (MREL) - 1 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
A61-45 (MREL) or 1 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR