Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) M

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  REGISTRATION  


PROCEDURE

Hide 1. LEARNING VALUES CONFIRMATION

This procedure uses the GTS to display the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the ECM.

A202032
0.104,0 2,0.344 1.896,0.344 10 false Learning Values Confirmation: 2.677,0.625 3.021,0.896 0.344,0.271 10 false Start 2.635,1.51 3.073,1.792 0.438,0.281 10 false Notice 2.469,2.302 3.208,2.583 0.74,0.281 10 false Select Item 2.01,4.906 3.677,5.198 1.667,0.292 10 false Confirm Learning Value(s) 2.5,4.396 2.823,4.646 0.323,0.25 10 false Next 2.906,1.896 3.229,2.146 0.323,0.25 10 false Next 2.906,1.063 3.229,1.313 0.323,0.25 10 false Next 1.542,5.167 1.885,5.448 0.344,0.281 10 false Back 5.302,3.073 6.323,3.396 1.021,0.323 10 false Retrieving Error 1.375,2.594 3.292,2.917 1.917,0.323 10 false - Injector Compensation Code 1.385,2.958 3.458,3.281 2.073,0.323 10 false - Pilot Quantity Learning Values 5.823,2.802 6.448,3.052 0.625,0.25 10 false Try Again 1.375,3.354 4.219,3.677 2.844,0.323 10 false - Crank Time Compensation Learning Values 2.719,5.906 3,6.188 0.281,0.281 10 false End 2.906,5.365 3.198,5.635 0.292,0.271 10 false Exit

HINT:
A204047

A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.

Powertrain > Engine > Utility
Tester Display
Learning Values Confirmation
50005 61 242

d.
A266977

Press "Next".


e.
A266978

Press "Next" again to proceed.


f.
A266979

Select the value to confirm and press "Next".


g.

When the next screen is displayed, confirm the contents and press "Exit".

A266980


Hide 2. LEARNING VALUES SAVE

This procedure uses the GTS to save the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the ECM in the GTS depending on the components being replaced.

A209877
0.135,0.031 1.625,0.219 1.49,0.188 10 false Learning Values Save: 3.24,0.604 3.594,0.76 0.354,0.156 10 false Start 3.448,1.021 3.813,1.198 0.365,0.177 10 false Next 3.448,1.854 3.813,2.031 0.365,0.177 10 false Next 3.177,1.479 3.625,1.656 0.448,0.177 10 false Notice 2.479,2.281 4.469,2.479 1.99,0.198 10 false Select Replaced Component(s) 2.49,2.615 3.417,2.781 0.927,0.167 10 false - Engine ECU 2.49,2.938 3.688,3.125 1.198,0.188 10 false - Engine Assembly 2.49,3.25 3.708,3.427 1.219,0.177 10 false - Injector Assembly 6.188,2.365 6.854,2.552 0.667,0.188 10 false Try Again 5.688,2.854 6.719,3.031 1.031,0.177 10 false Retrieving Error 3.052,4.333 3.396,4.51 0.344,0.177 10 false Next 2.302,5.042 4.438,5.208 2.135,0.167 10 false Learning Value(s) Save Complete 3.458,5.531 3.729,5.677 0.271,0.146 10 false Exit 3.292,6.031 3.604,6.198 0.313,0.167 10 false End 0.323,6.031 2.042,6.229 1.719,0.198 10 false No Learning Value to Save 2.167,6.25 2.417,6.417 0.25,0.167 10 false OK 4.906,5.26 5.563,5.438 0.656,0.177 10 false Overwrite 5.625,5.052 6.813,5.219 1.188,0.167 10 false Confirm Overwrite

HINT:
·

When replacing the engine assembly or the injector assembly together with the ECM, this function automatically determines the data which can be transferred (old data) and saves the data in the GTS.

·
A204057

When there is no data to read from the ECM, manually perform the procedure to register each compensation code and learning value in the ECM.

·
A204058

A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save.

Powertrain > Engine > Utility
Tester Display
Learning Values Save
50005 61 240

d.
A268095

Press "Next".


e.
A268096

Press "Next" again to proceed.


f.
A268097

Select any components being replaced and press "Next". If no applicable components are displayed, press "Next" without selecting anything.


g.
A204055

If the overwrite confirmation screen is displayed, press "Overwrite".


h.
A268098

When the operation is finished, confirm the date and time of the save operation, and press "Exit".


Hide 3. LEARNING VALUES WRITE

This procedure uses the GTS to write all of the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the GTS to the ECM.

A202034
0.146,0.115 1.635,0.458 1.49,0.344 10 Learning Values Write: 2.677,0.656 3.021,0.927 0.344,0.271 10 Start 2.625,1.521 3.063,1.802 0.438,0.281 10 Notice 2.042,2.354 3.656,2.635 1.615,0.281 10 Saved Date Confirmation 1.969,3.792 3.708,4.083 1.74,0.292 10 Following Setting Complete 2.49,2.875 2.813,3.125 0.323,0.25 10 Yes 2.458,4.26 2.781,4.51 0.323,0.25 10 Next 2.438,1.906 2.76,2.156 0.323,0.25 10 Next 2.927,1.063 3.25,1.313 0.323,0.25 10 Next 5.281,5.365 5.573,5.635 0.292,0.271 10 Exit 3.896,5.885 4.177,6.167 0.281,0.281 10 End 2.521,5.375 2.813,5.646 0.292,0.271 10 Exit 6.188,5.115 6.531,5.396 0.344,0.281 10 Back 1.531,5.125 1.875,5.406 0.344,0.281 10 Back 5.302,2.115 6.323,2.438 1.021,0.323 10 Retrieving Error 5.844,1.646 6.469,1.896 0.625,0.25 10 Try Again 5.26,2.448 6.385,2.771 1.125,0.323 10 Writing Code Fail 4.313,1.396 5,1.656 0.688,0.26 10 Data Error 4.365,1.146 4.927,1.406 0.563,0.26 10 No Data 4.313,4.865 6.125,5.156 1.813,0.292 10 Execute Following Functions 2.115,4.865 3.573,5.156 1.458,0.292 10 All Setting(s) Complete

HINT:
A204063

A malfunction may occur when writing the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write.

Powertrain > Engine > Utility
Tester Display
Learning Values Write
50005 61 241

d.
A268099

Press "Next".


e.
A268100

Press "Next" again to proceed.


f.
A204062

If the "Error Learning Values Write" screen indicating a problem with the saved value(s) or that there are no saved values is displayed, perform "Learning Values Save" again.


g.
A204064

Confirm the date and time of the save operation, and then press "Yes".


h.
A268101

Confirm the contents, and then press "Next".


i.
A268102

If any instructions are displayed on the GTS, manually perform the procedure to register each applicable compensation code or learning value in the ECM.


j.

Clear the DTCs.


Hide 4. INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

NOTICE:
·

When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing fuel injector compensation codes must be input into the new ECM.

·

Fuel injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect fuel injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

When a fuel injector compensation code is input into the ECM, the pilot quantity learning values stored in the ECM are initialized. Also, DTC P062F is stored when the pilot quantity learning values are initialized.



A203986
2.583,2.135 2.583,2.573 false 0.115,0.115 0.76,0.271 0.646,0.156 10 *a 2.51,2.635 2.729,2.885 0.219,0.25 10 *b
*a Example
*b Injector Compensation Code


a.

After replacing fuel injector(s) with new one(s), input compensation code(s) of the fuel injector(s) into the ECM as follows:

HINT:
·

Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each fuel injector.

·

When only one or more fuel injectors are replaced, input the fuel injector compensation code(s), perform pilot quantity learning, and then clear the DTCs.

·

When the ignition switch is turned to ON after replacing the ECM, DTC P062F is stored. This indicates that the fuel injector compensation code(s) need to be registered. Manually clear the DTC upon completion of pilot quantity learning.



i.

Input the compensation code(s), which is/are imprinted on the head portion(s) of the new fuel injector(s), into the GTS.


ii.

Input the new compensation code(s) into the ECM using the GTS.


iii.

Turn the GTS off and turn the ignition switch off.


iv.

Wait for at least 30 seconds.


v.

Turn the ignition switch to ON and turn the GTS on.


vi.

Perform pilot quantity learning.


vii.

Clear DTC P062F stored in the ECM using the GTS (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>DTC CHECK / CLEAR).

NOTICE:

If the DTCs are cleared without performing pilot quantity learning, DTC P062F is stored the next time the ignition switch is turned to ON.




b.

Register compensation codes.

A202035
0.146,0.125 2.042,0.406 1.896,0.281 10 Injector Compensation Code: 3.427,0.531 3.771,0.802 0.344,0.271 10 Start 2.823,2.833 4.469,3.115 1.646,0.281 10 Select Cylinder Number 3.688,3.229 4.01,3.469 0.323,0.24 10 Next 3.104,2.063 4.198,2.344 1.094,0.281 10 Select Function 3.688,2.458 4.01,2.708 0.323,0.25 10 Next 3.385,1.323 3.823,1.604 0.438,0.281 10 Notice 2.344,5.917 4.844,6.208 2.5,0.292 10 Register Compensation Code Complete 3.26,4.542 3.583,4.792 0.323,0.25 10 Next 3.688,1.698 4.01,1.948 0.323,0.25 10 Next 3.667,0.948 3.99,1.198 0.323,0.25 10 Next 3.469,7.063 3.75,7.344 0.281,0.281 10 End 3.646,6.406 3.938,6.677 0.292,0.271 10 Exit 1.74,6.146 2.083,6.427 0.344,0.281 10 Next 1.604,4.906 2.938,5.229 1.333,0.323 10 Invalid Number Input 0.854,5.188 1.479,5.438 0.625,0.25 10 Try Again 4.417,4.844 5.375,5.177 0.958,0.333 10 Compensation Failure 1.292,4.052 3.656,4.375 2.365,0.323 10 Confirm Injector Compensation Code 1.292,3.729 4.031,4.052 2.74,0.323 10 Input Injector Compensation Code Manually 5.583,5.188 6.208,5.438 0.625,0.25 10 Try Again 5.146,3.917 5.792,4.24 0.646,0.323 10 Keyboard 4.156,4.219 5.073,4.469 0.917,0.25 10 OK or Cancel 4.385,3.708 4.75,3.958 0.365,0.25 10 Input

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.
A295512

Enter the following menus: Powertrain / Engine and ECT / Utility / Injector Compensation.

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 61 239

v.

Press Next.


vi.
A295513

Press Next again to proceed.


vii.
A297892

Select "Set Compensation Code".


viii.

Press Next.


ix.
A295515

Select the number of the cylinder corresponding to the fuel injector compensation code that you want to register.


x.

Press Next.


xi.
A295516

Register compensation code.

1.

Press Input.

2.
A241920

Manually input the cylinder compensation code using the keyboard on the GTS screen. The code is a 30-digit, alphanumeric value printed on the injector head portion.

HINT:

Each fuel injector compensation code is unique. The compensation code for each selected cylinder must be input into the GTS correctly.


3.

Confirm that the compensation code for the selected cylinder is correct, and then press OK.



xii.
A297893
0.104,0.094 0.417,0.292 0.313,0.198 10 *a
*a Example


Check that the compensation code displayed on the screen is correct by comparing it with the 30-digit alphanumeric value on the head portion of the fuel injector.

NOTICE:

If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


HINT:
·

If a wrong compensation code is input or read, return to the Input Value screen by pressing Input.

·

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.




xiii.

Press Next to register the compensation code in the ECM.

HINT:
·

If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

·

If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.




xiv.
A295519

If you want to continue with other compensation code registrations, press Next. To finish the registration, press Exit.


xv.

Turn the ignition switch off, and then turn the GTS off.


xvi.

Wait for at least 30 seconds.


xvii.

Turn the ignition switch to ON, and then turn the GTS on.


xviii.

Perform pilot quantity learning.


xix.

Clear DTC P062F stored in the ECM using the GTS (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>DTC CHECK / CLEAR).

NOTICE:

If the DTCs are cleared without performing pilot quantity learning, DTC P062F is stored the next time the ignition switch is turned to ON.




Hide 5. PILOT QUANTITY LEARNING

·

"Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning (Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.

·

This procedure uses the GTS to perform "Pilot Quantity Learning".

·

When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).


A204080
0.094,0.073 1.708,0.354 1.615,0.281 10 Pilot Quantity Learning: 2.885,0.833 3.219,1.125 0.333,0.292 10 Next 2.833,3.813 3.167,4.104 0.333,0.292 10 Exit 2.823,2.76 3.156,3.052 0.333,0.292 10 Next 2.844,1.656 3.177,1.948 0.333,0.292 10 Next 1.854,1.208 3.656,1.552 1.802,0.344 10 Wait until Learning Possible 2.583,0.406 2.917,0.698 0.333,0.292 10 Start 1.229,2.333 4.25,2.625 3.021,0.292 10 Operate Accelerator Pedal to Perform Learning 1.25,3.385 4.25,3.646 3,0.26 10 Operate Accelerator Pedal to Perform Learning 2.635,4.25 2.938,4.469 0.302,0.219 10 End 4.958,2.333 5.99,2.542 1.031,0.208 10 Condition Error 4.958,3.385 5.99,3.594 1.031,0.208 10 Condition Error 6.24,2.531 6.896,2.74 0.656,0.208 10 Try Again 6.26,3.573 6.917,3.781 0.656,0.208 10 Try Again

NOTICE:

After completing this procedure, clear the DTCs using the GTS.


HINT:
·
A204031

If "Exit" is pushed during the step where the accelerator pedal is operated and "Pilot Quantity Learning" is canceled, turn the ignition switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.

·

If an error occurs during learning, check the vehicle condition after turning the ignition switch off, and then perform learning again.

·

If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the ignition switch off, and then perform learning again.

·
A297895

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot quantity learning.

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 61 235

e.
A297896

Press "Next".


f.
A297897

Press "Next" again to proceed.


g.
A297950
0.115,0.073 0.427,0.271 0.313,0.198 10 *a
*a Example


Confirm that the atmospheric pressure screen is displayed.

i.

Confirm the displayed atmospheric pressure.

Standard:

Atmosphere Pressure is 85 kPa or more


NOTICE:
·

If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".

·

If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.




ii.

If the atmospheric pressure is within the standard range, proceed to the next screen.



h.
A297951
0.115,0.073 0.427,0.271 0.313,0.198 10 *a
*a Example


Confirm the condition of the engine and wait until learning can be performed.

Essential Conditions for Learning
GTS Display Standard
Coolant Temp 70 to 100°C
Intake Air -25 to 120°C
Fuel Temperature 30 to 96°C
Fuel Return Temp 35 to 110°C
Battery Voltage 10 V or higher
Pilot Quantity State(CAT) READY

HINT:
·

If the values deviate from the standard above, "Pilot Quantity Learning" enters a standby state or is canceled.

·

When the essential conditions to perform learning are met, the screen will change automatically.



NOTICE:
·

Using the GTS, make sure that DTCs other than DTC P062F are not output.

·

If DTCs other than DTC P062F are output, perform troubleshooting for those DTCs.




i.
A297952
0.104,0.063 0.417,0.26 0.313,0.198 10 *a
*a Example


A204032

Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or more for no more than 2 seconds, and then let the engine return to idling.

HINT:
·

After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.

·

It is possible to confirm the status of the learning operation during "Pilot Quantity Learning" by observing the blinking pattern of the glow indicator light.



Glow Indicator Light Blinking Pattern
Learning Status Glow Indicator Light Condition
Conditions essential to start learning have not been met Blinking at 0.5 second intervals
Conditions essential to start learning have been met Blinking at 1 second intervals
During racing (learning is being performed) Blinking at 1 second intervals
Learning is finished Off
Learning has been canceled Blinking at 1.5 second intervals
Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern) Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)

A178592
0.031,0.01 2.354,0.302 2.323,0.292 10 Glow Indicator Light Blinking Pattern 0.083,0.833 0.354,1.073 0.271,0.24 10 ON 0.052,1.771 0.375,2.063 0.323,0.292 10 OFF 0.469,0.302 3.073,0.594 2.604,0.292 10 Essential Conditions for Learning not Met 3.167,0.583 4.458,0.917 1.292,0.333 10 Performing Learning 4.479,0.24 7.104,0.552 2.625,0.313 10 Canceled (not due to injector malfunction) 1.25,1.771 2.042,2.094 0.792,0.323 10 0.5 seconds 4.01,2.063 4.802,2.385 0.792,0.323 10 1.5 seconds 3.615,1.771 4.406,2.063 0.792,0.292 10 1.5 seconds 2.927,1.771 3.583,2.073 0.656,0.302 10 1 second 1.354,2.063 2.146,2.385 0.792,0.323 10 0.5 seconds 3.125,2.063 3.781,2.365 0.656,0.302 10 1 second

A178593
1.656,1.115 1.313,1.844 false 3.281,1.229 2.479,1.823 false 5.792,1.031 5.594,1.854 false 0.792,2.917 1.01,2.917 false 0.792,2.917 0.927,2.708 false 2.177,2.708 2.417,3.625 2.417,3.625 3.729,3.615 false 2.469,2.917 2.656,3.615 false 0.115,0.104 6.479,0.469 6.365,0.365 10 Glow Indicator Light Blinking Pattern (Learning Canceled Due to Cylinder 2 and 3 Injector Malfunction) 1.729,0.979 3.052,1.333 1.323,0.354 10 Beginning of Cycle 3.01,0.594 3.552,0.917 0.542,0.323 10 1 Cycle 3.323,1.063 4.948,1.417 1.625,0.354 10 Blinks 2 times to indicate problem with cylinder 2 5.833,0.948 7.021,1.302 1.188,0.354 10 Beginning of Cycle 0.021,2.833 0.813,3.125 0.792,0.292 10 0.1 seconds 1.448,3.323 2.24,3.469 0.792,0.146 10 3.6 seconds 3.781,3.531 4.615,3.76 0.833,0.229 10 0.8 seconds 0.24,1.927 0.49,2.115 0.25,0.188 10 ON 0.167,2.469 0.5,2.635 0.333,0.167 10 OFF 4.708,2.823 5.5,2.969 0.792,0.146 10 2.4 seconds 2.833,3.271 3.625,3.417 0.792,0.146 10 2.3 seconds


j.
A297953

When the screen changes, push "Exit".


k.

Turn the ignition switch off, and then turn the GTS off.


l.

Wait for at least 10 seconds.


m.

Turn the ignition switch to ON, and then turn the GTS on.



o.

Turn the ignition switch off.

NOTICE:

Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the ignition switch off.


HINT:
·

The main relay turns off after the learned value is stored in the ECM.

·

The main relay turns off within approximately 5 to 10 seconds of turning the ignition switch off.




Hide 6. PILOT QUANTITY LEARNING (DETAIL)

·

"Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning (Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.

It takes time to clear the learned values and perform learning for all cylinders.

·

This procedure uses the GTS to perform "Pilot Quantity Learning (Detail)".

·

When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).


A204080
0.052,0.031 2.552,0.313 2.5,0.281 10 Pilot Quantity Learning(Detail): 2.865,0.823 3.198,1.115 0.333,0.292 10 Next 2.854,3.844 3.188,4.135 0.333,0.292 10 Exit 2.865,2.75 3.198,3.042 0.333,0.292 10 Next 2.865,1.667 3.198,1.958 0.333,0.292 10 Next 1.875,1.208 3.677,1.552 1.802,0.344 10 Wait until Learning Possible 2.604,0.406 2.938,0.698 0.333,0.292 10 Start 1.25,2.344 4.333,2.635 3.083,0.292 10 Operate Accelerator Pedal to Perform Learning 1.271,3.385 4.271,3.646 3,0.26 10 Operate Accelerator Pedal to Perform Learning 2.635,4.25 2.969,4.469 0.333,0.219 10 End 4.948,2.333 5.979,2.542 1.031,0.208 10 Condition Error 4.948,3.406 5.979,3.615 1.031,0.208 10 Condition Error 6.271,2.542 6.927,2.75 0.656,0.208 10 Try Again 6.281,3.583 6.938,3.792 0.656,0.208 10 Try Again

NOTICE:

After completing this procedure, clear the DTCs using the GTS.


HINT:
·
A206037

If "Exit" is pushed during the step where the accelerator pedal is operated and "Pilot Quantity Learning (Detail)" is canceled, turn the ignition switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.

·

If an error occurs during learning, check the vehicle condition after turning the ignition switch off, and then perform learning again.

·

If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the ignition switch off, and then perform learning again.

·
A297954
0.104,0.073 0.417,0.271 0.313,0.198 10 *a
*a Example


A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot quantity learning (Detail).

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning(Detail)
50005 61 236

e.
A297955

Press "Next".


f.
A297956

Press "Next" again to proceed.


g.
A297957
0.083,0.083 0.396,0.281 0.313,0.198 10 *a
*a Example


Confirm that the atmospheric pressure screen is displayed.

i.

Confirm the displayed atmospheric pressure.

Standard:

Atmosphere Pressure is 85 kPa or more


NOTICE:
·

If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".

·

If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.




ii.

If the atmospheric pressure is within the standard range, proceed to the next screen.



h.
A297958
0.156,0.115 0.469,0.313 0.313,0.198 10 *a
*a Example


Confirm the condition of the engine and wait until learning can be performed.

Essential Conditions for Learning
GTS Display Standard
Coolant Temp 70 to 100°C
Intake Air -25 to 120°C
Fuel Temperature 30 to 96°C
Fuel Return Temp 35 to 110°C
Battery Voltage 10 V or higher
Pilot Quantity State(CAT) READY

HINT:
·

If the values deviate from the standard above, "Pilot Quantity Learning (Detail)" enters a standby state or is canceled.

·

When the essential conditions to perform learning are met, the screen will change automatically.



NOTICE:
·

Using the GTS, make sure that DTCs other than DTC P062F are not output.

·

If DTCs other than DTC P062F are output, perform troubleshooting for those DTCs.




i.
A297959
0.146,0.083 0.458,0.281 0.313,0.198 10 *a
*a Example


A206038

Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or more for no more than 2 seconds, and then let the engine return to idling.

HINT:
·

After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.

·

It is possible to confirm the status of the learning operation during "Pilot Quantity Learning (Detail)" by observing the blinking pattern of the glow indicator light.



Glow Indicator Light Blinking Pattern
Learning Status Glow Indicator Light Condition
Conditions essential to start learning have not been met Blinking at 0.5 second intervals
Conditions essential to start learning have been met Blinking at 1 second intervals
During racing (learning is being performed) Blinking at 1 second intervals
Learning is finished Off
Learning has been canceled Blinking at 1.5 second intervals
Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern) Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)

A178592
0.031,0.01 2.354,0.302 2.323,0.292 10 Glow Indicator Light Blinking Pattern 0.083,0.833 0.354,1.073 0.271,0.24 10 ON 0.052,1.771 0.375,2.063 0.323,0.292 10 OFF 0.469,0.302 3.073,0.594 2.604,0.292 10 Essential Conditions for Learning not Met 3.167,0.583 4.458,0.917 1.292,0.333 10 Performing Learning 4.479,0.24 7.104,0.552 2.625,0.313 10 Canceled (not due to injector malfunction) 1.25,1.771 2.042,2.094 0.792,0.323 10 0.5 seconds 4.01,2.063 4.802,2.385 0.792,0.323 10 1.5 seconds 3.615,1.771 4.406,2.063 0.792,0.292 10 1.5 seconds 2.927,1.771 3.583,2.073 0.656,0.302 10 1 second 1.354,2.063 2.146,2.385 0.792,0.323 10 0.5 seconds 3.125,2.063 3.781,2.365 0.656,0.302 10 1 second

A178593
1.656,1.115 1.313,1.844 false 3.281,1.229 2.479,1.823 false 5.792,1.031 5.594,1.854 false 0.792,2.917 1.01,2.917 false 0.792,2.917 0.927,2.708 false 2.177,2.708 2.417,3.625 2.417,3.625 3.729,3.615 false 2.469,2.917 2.656,3.615 false 0.115,0.104 6.479,0.469 6.365,0.365 10 Glow Indicator Light Blinking Pattern (Learning Canceled Due to Cylinder 2 and 3 Injector Malfunction) 1.729,0.979 3.052,1.333 1.323,0.354 10 Beginning of Cycle 3.01,0.594 3.552,0.917 0.542,0.323 10 1 Cycle 3.323,1.063 4.948,1.417 1.625,0.354 10 Blinks 2 times to indicate problem with cylinder 2 5.833,0.948 7.021,1.302 1.188,0.354 10 Beginning of Cycle 0.021,2.833 0.813,3.125 0.792,0.292 10 0.1 seconds 1.448,3.323 2.24,3.469 0.792,0.146 10 3.6 seconds 3.781,3.531 4.615,3.76 0.833,0.229 10 0.8 seconds 0.24,1.927 0.49,2.115 0.25,0.188 10 ON 0.167,2.469 0.5,2.635 0.333,0.167 10 OFF 4.708,2.823 5.5,2.969 0.792,0.146 10 2.4 seconds 2.833,3.271 3.625,3.417 0.792,0.146 10 2.3 seconds


j.
A297960

When the screen changes, push "Exit".


k.

Turn the ignition switch off, and then turn the GTS off.


l.

Wait for at least 10 seconds.


m.

Turn the ignition switch to ON, and then turn the GTS on.



o.

Turn the ignition switch off.

NOTICE:

Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the ignition switch off.


HINT:
·

The main relay turns off after the learned value is stored in the ECM.

·

The main relay turns off within approximately 5 to 10 seconds of turning the ignition switch off.




Hide 7. PILOT QUANTITY LEARNING VALUE CLEAR

HINT:
·

If the atmospheric pressure is below the threshold value, "Pilot Quantity Learning" will not be completed and DTC P062F is stored. After "Pilot Quantity Learning Value Clear" is performed, DTC P062F will not be stored.

·

Clear the learned values using the following procedure.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON, and then turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot Quantity Learning Value Clear

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning Values Clear
50005 61 2142

d.
A297961

Press "Next".


e.
A297962
0.146,0.094 0.458,0.292 0.313,0.198 10 *a
*a Example


Confirm that the atmospheric pressure screen is displayed.

i.

Confirm the displayed atmospheric pressure.

Standard:

Atmosphere Pressure is below 85 kPa


NOTICE:
·

If the atmospheric pressure is higher than the standard range for performing "Pilot Quantity Learning Value Clear", do not clear the learned values. Instead, perform "Pilot Quantity Learning".

·

When the atmospheric pressure is higher than the standard range, perform "Pilot Quantity Learning" without initializing the learned values using "Pilot Quantity Learning Value Clear". If the learned values are initialized when the atmospheric pressure is higher than the standard range, the following symptoms may appear. Be sure to correctly follow procedures.

·

Driveability problems

·

Rough idle

·

Emission of white or black smoke, etc.





ii.

Proceed to the next screen.



f.
A297963

Select the cylinders whose learned value will be cleared.

NOTICE:
·

Multiple cylinders can be selected.

·

Only the cylinders for which fuel injector compensation codes have been written must have their learned value cleared.




g.

After selecting the cylinders whose learned value will be cleared, press "Next" to begin the initialization.


h.
A297964

When the screen changes, push "Exit".


i.

Turn the ignition switch off, and then turn the GTS off.


j.

Wait for at least 10 seconds.


k.

Turn the ignition switch to ON, and then turn the GTS on.



m.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


n.

Turn the ignition switch to ON for 1 second.


o.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

p.

Read the DTCs.


q.

Confirm that no DTCs are output.


Hide 8. DESCRIPTION OF VIN

NOTICE:

The Vehicle Identification Number (VIN) must be input into the replacement ECM.


HINT:

The VIN is a 17-digit alphanumeric number. The GTS is required to register the VIN.


a.

Read VIN: Explains the VIN reading process in a flowchart. This process allows the Vin stored in the ECM to be read, in order to confirm that the two VINs, provided with the vehicle and stored in the vehicle's ECM, are the same.


b.

Write VIN: Explains the VIN writing process in a flowchart. This process allows the VIN to be input into the ECM. If the ECM is changed, or the ECM VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.


Hide 9. READ VIN

a.

Confirm the vehicle VIN.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / VIN.

Powertrain > Engine > Utility
Tester Display
VIN
50005 61 196
A297965
3.885,4.552 4.448,5.104 false 3.208,1.458 4.396,1.448 false 4.51,1.365 4.823,1.563 0.313,0.198 10 *a 3.469,2.792 3.781,2.99 0.313,0.198 10 *b 1.271,3.396 1.583,3.594 0.313,0.198 10 *c 3.5,3.406 3.813,3.604 0.313,0.198 10 *d 5.729,3.385 6.042,3.583 0.313,0.198 10 *e 5.729,5.052 6.042,5.25 0.313,0.198 10 *f 3.479,6.177 3.792,6.375 0.313,0.198 10 *f 1.25,4.771 1.563,4.969 0.313,0.198 10 *f 4.51,5.094 4.823,5.292 0.313,0.198 10 *g 3.344,7.208 3.656,7.406 0.313,0.198 10 *h
*a Select VIN Read *b Next
*c DTC P0630 Set *d VIN Previously Stored
*e VIN Not Stored *f Exit
*g 17-digit VIN displayed *h End



Hide 10. WRITE VIN

a.

Confirm the vehicle VIN.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / VIN.

Powertrain > Engine > Utility
Tester Display
VIN
50005 61 196
A297966
1.542,1.563 2.792,1.458 false 5.969,5.083 6.594,5.51 false 2.885,1.375 3.198,1.573 0.313,0.198 10 *a 1.781,5.771 2.094,5.969 0.313,0.198 10 *b 1.427,6.333 1.74,6.531 0.313,0.198 10 *b 5.552,6.365 5.865,6.563 0.313,0.198 10 *b 1.625,7.365 1.938,7.563 0.313,0.198 10 *c 6.646,5.51 6.958,5.708 0.313,0.198 10 *e 5.583,3.823 5.896,4.021 0.313,0.198 10 *d
*a Select VIN Write *b Next
*c Continue to next illustration *d VIN Previously Stored
*e 17-digit VIN displayed - -


A297967
1.604,4.271 2.417,3.792 false 1.271,3.26 1.583,3.458 0.313,0.198 10 *a 2.479,3.688 2.792,3.885 0.313,0.198 10 *b 1.469,4.969 1.781,5.167 0.313,0.198 10 *c 0.917,5.406 1.229,5.604 0.313,0.198 10 *c 3.438,6.719 3.75,6.917 0.313,0.198 10 *c 5.698,6.719 6.01,6.917 0.313,0.198 10 *c 3.469,5.51 3.781,5.708 0.313,0.198 10 *d 5.677,5.531 5.99,5.729 0.313,0.198 10 *d 0.198,5.719 0.51,5.917 0.313,0.198 10 *g 1.281,8.052 1.594,8.25 0.313,0.198 10 *e 1.115,8.396 1.427,8.594 0.313,0.198 10 *f
*a Input *b Manually input the VIN
*c OK *d Input Error
*e Next *f Continue to next illustration
*g Example - -


A297968
1.781,1.26 2.094,1.458 0.313,0.198 10 *a 4.625,1.302 4.938,1.5 0.313,0.198 10 *b 5.26,2.458 5.573,2.656 0.313,0.198 10 *c 1.802,3.781 2.115,3.979 0.313,0.198 10 *c 1.646,4.167 1.958,4.365 0.313,0.198 10 *d 5.948,3.208 6.26,3.406 0.313,0.198 10 *d 4.292,2.813 4.604,3.01 0.313,0.198 10 *e 4.469,3.229 4.781,3.427 0.313,0.198 10 *f
*a Writing Successful *b Writing Error
*c Exit *d End
*e Try Again *f To VIN Write Screen