Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2012.12–2013.11
RM3090E _57 Power Source / Network _008434 NETWORKING _0048454 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U1002  Lost Communication with Gateway Module  


DESCRIPTION

·

The main body ECU (multiplex network body ECU) stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the sub bus 1.

·

When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to the sub bus 1, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to the sub bus 1. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to the sub bus 1 when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to the sub bus 1, the main body ECU (multiplex network body ECU) determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U1002 Lost Communication with Gateway Module Lost communication with the gateway module.
·

Sub bus 1 circuit

·

Main body ECU (multiplex network body ECU) CAN main wire or connector

·

Multiplex network door ECU CAN branch wire or connector

·

Position control ECU and switch assembly CAN branch wire or connector*1

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Multiplex network door ECU

·

Position control ECU and switch assembly*1

·

No. 4 CAN junction connector*2

·

No. 5 CAN junction connector

·

No. 6 CAN junction connector


Main body ECU (multiplex network body ECU)

*1: w/ Seat Memory

*2: for Power Seat

For vehicles with a power back door system.


WIRING DIAGRAM

C280386E02
5.865,0.719 6.479,0.917 0.615,0.198 10 false CANP 5.865,1.375 6.479,1.573 0.615,0.198 10 false CANN 0.854,5.208 1.469,5.406 0.615,0.198 10 false CANN 0.844,4.76 1.458,4.958 0.615,0.198 10 false CANP 0.156,5.552 0.771,5.75 0.615,0.198 10 false U18 0.167,5.708 2.615,6.063 2.448,0.354 10 false Multiplex Network Door ECU 0.198,1.615 0.813,1.813 0.615,0.198 10 false e6 0.208,1.802 1.802,2.156 1.594,0.354 10 false Position Control ECU and Switch Assembly*3 1.365,1.177 1.979,1.375 0.615,0.198 10 false 7 1.375,0.708 1.99,0.906 0.615,0.198 10 false 8 1.938,3.792 3.938,4.135 2,0.344 10 false N30 1.948,3.958 3.948,4.302 2,0.344 10 false No. 4 CAN Junction Connector*1 3.208,3.281 5.208,3.625 2,0.344 10 false 8 3.208,2.844 5.208,3.188 2,0.344 10 false 2 3.229,1.156 5.229,1.5 2,0.344 10 false 7 3.219,0.708 5.219,1.052 2,0.344 10 false 1 2.281,0.698 4.281,1.042 2,0.344 10 false 3 2.292,1.167 4.292,1.51 2,0.344 10 false 9 4.01,2.833 6.01,3.177 2,0.344 10 false 10 4.01,3.271 6.01,3.615 2,0.344 10 false 21 4.99,2.823 6.99,3.167 2,0.344 10 false 9 5,3.292 7,3.635 2,0.344 10 false 20 4.01,5.083 6.01,5.427 2,0.344 10 false 19 4.094,4.604 6.094,4.948 2,0.344 10 false 8 1.354,5.083 3.354,5.427 2,0.344 10 false 14 1.365,4.625 3.365,4.969 2,0.344 10 false 13 3.729,5.521 5.729,5.865 2,0.344 10 false N32 3.74,5.688 5.74,6.031 2,0.344 10 false No. 5 CAN Junction Connector 5.156,3.76 7.042,4.198 1.885,0.438 10 false N31 5.156,3.927 7.042,4.365 1.885,0.438 10 false No. 6 CAN Junction Connector 5.667,2.823 6.24,3.177 0.573,0.354 10 false 3 5.667,3.281 6.24,3.635 0.573,0.354 10 false 2 5.854,2.823 6.427,3.177 0.573,0.354 10 false CANH 5.875,3.521 6.448,3.875 0.573,0.354 10 false CANL 5.479,1.615 6.063,2.156 0.583,0.542 10 false G79 5.479,1.771 7.115,2.146 1.635,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.615,1.156 6.198,1.698 0.583,0.542 10 false 10 5.677,0.708 6.25,1.063 0.573,0.354 10 false 9 3.688,2.167 5.688,2.51 2,0.344 10 false *2 3.396,2.167 5.396,2.51 2,0.344 10 false *2 0.198,6.167 2.198,6.51 2,0.344 10 false *1: for Power Seat 0.833,0.823 1.448,1.021 0.615,0.198 10 false CANP 0.833,1.271 1.448,1.469 0.615,0.198 10 false CANN 0.198,6.469 2.198,6.813 2,0.344 10 false *2: except Power Seat 2.104,6.177 4.104,6.521 2,0.344 10 false *3: w/ Seat Memory

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



HINT:

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


PROCEDURE

1.CHECK SUB BUS 1
a.
C216700C09
0.531,2.51 0.958,2.75 0.427,0.24 0.479,0.875 0.917,1.115 0.438,0.24 1.719,0.896 1.375,0.229 1.375,0.229 1.188,0.229 true 1.427,0.885 1.146,0.542 1.146,0.542 1.01,0.542 true 2.146,2.802 2.292,3.083 2.292,3.083 2.469,3.083 true 1.969,0.875 2.104,0.51 2.104,0.51 2.292,0.51 true 0.104,1.958 0.323,2.156 0.219,0.198 10 *b 0.104,0.073 0.323,0.271 0.219,0.198 10 *a 0.781,0.146 1.156,0.302 0.375,0.156 10 CANL 0.604,0.469 1.052,0.667 0.448,0.198 10 CANH 2.531,3.01 2.844,3.208 0.313,0.198 10 BAT 0.615,2.552 0.906,2.75 0.292,0.198 10 G14 0.573,0.917 0.896,1.115 0.323,0.198 10 N31 2.344,0.438 2.656,0.635 0.313,0.198 10 E
*a Component with harness connected
(No. 6 CAN Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Resistance: Malfunction
N31-3 (CANH) - N31-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 53 Ω: Short in line
N31-3 (CANH) - N31-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
N31-3 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
N31-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
N31-3 (CANH) - N31-1 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short
N31-2 (CANL) - N31-1 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short



Result:
Result Proceed to
OK A
NG
- Open in CAN main wire
B
NG
- Short in CAN bus wire
C
NG
- +B short
- Ground short
D



A

2.CHECK FOR DTC

B

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 CAN JUNCTION CONNECTOR)

C

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)

D

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)
2.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC U1002 is output from main body ECU (multiplex network body ECU) A
Other DTC is output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.
C266890C05
2.406,1.094 2.813,1.354 0.406,0.26 0.896,0.76 1.104,0.76 1.104,0.76 1.385,1.167 true 0.896,1.635 1.135,1.635 1.135,1.635 1.375,1.302 true 1.083,1.865 1.323,1.865 1.323,1.865 1.448,1.292 true 0.969,0.5 1.177,0.5 1.177,0.5 1.458,1.188 true 0.063,0.052 0.375,0.208 0.313,0.156 10 *a 2.479,1.146 2.792,1.302 0.313,0.156 10 N32 0.344,0.688 0.885,0.875 0.542,0.188 10 CANH*c 0.365,1.552 0.917,1.75 0.552,0.198 10 CANL*c 0.552,1.781 1.104,1.979 0.552,0.198 10 CANL*b 0.406,0.406 0.948,0.594 0.542,0.188 10 CANH*b
*a Rear view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 6 CAN Junction Connector
*c to No. 4 CAN Junction Connector (for Power Seat) or Main Body ECU (Multiplex Network Body ECU) (except Power Seat)


Disconnect the No. 5 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N32-9 (CANH) - N32-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N32-10 (CANH) - N32-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to No. 6 CAN junction connector CAN main wire) B
NG (to No. 4 CAN junction connector CAN main wire) (for Power Seat) C
NG (to main body ECU [multiplex network body ECU] CAN main wire) (except Power Seat) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

4.CONNECT CONNECTOR

C

6.CONNECT CONNECTOR

D

10.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)
a.
C210060C18
0.323,0.917 0.802,1.167 0.479,0.25 0.948,0.49 1.115,0.49 1.115,0.49 1.344,0.865 true 2.24,0.344 2.063,0.344 2.063,0.344 1.729,0.854 true 0.51,0.417 0.948,0.594 0.438,0.177 10 CANH 0.427,0.958 0.844,1.188 0.417,0.229 10 N31 0.063,0.063 0.271,0.24 0.208,0.177 10 *a 2.313,0.281 2.75,0.458 0.438,0.177 10 CANL
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)


Disconnect the No. 6 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-3 (CANH) - N31-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

6.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.
C277472C03
1.438,0.135 1.854,0.385 0.417,0.25 1.292,1.125 0.917,0.75 0.917,0.75 0.667,0.75 true 1.26,1.448 1.01,1.74 1.01,1.74 0.677,1.74 true 1.448,1.146 1.25,0.417 1.25,0.417 1,0.417 true 1.448,1.417 1.281,2 1.281,2 1.115,2 true 0.104,0.083 0.417,0.24 0.313,0.156 10 *a 1.521,0.177 1.917,0.417 0.396,0.24 10 N30 0.125,0.677 0.75,0.896 0.625,0.219 10 CANH*b 0.167,1.667 0.813,1.917 0.646,0.25 10 CANL*b 0.542,1.917 1.188,2.167 0.646,0.25 10 CANL*c 0.458,0.333 1.083,0.552 0.625,0.219 10 CANH*c
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to No. 5 CAN Junction Connector


Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-1 (CANH) - N30-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N30-2 (CANH) - N30-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to main body ECU [multiplex network body ECU] CAN main wire) B
NG (to No. 5 CAN junction connector CAN main wire) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

8.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 4 CAN JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 4 CAN JUNCTION CONNECTOR)
a.
C277474C01
0.292,0.969 0.833,1.26 0.542,0.292 2.604,1.604 2.354,1.604 2.354,1.604 1.854,1.104 true 2.438,1.927 2.188,1.927 2.188,1.927 1.802,1.094 true 0.104,0.094 0.417,0.25 0.313,0.156 10 *a 2.646,1.531 3.208,1.865 0.563,0.333 10 CANP 0.417,1.031 0.979,1.365 0.563,0.333 10 G79 2.479,1.844 3.115,2.115 0.635,0.271 10 CANN
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-9 (CANP) - G79-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 4 CAN JUNCTION CONNECTOR)

10.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 5 CAN JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 5 CAN JUNCTION CONNECTOR)
a.
C277474C01
0.292,0.969 0.833,1.26 0.542,0.292 2.604,1.604 2.354,1.604 2.354,1.604 1.854,1.104 true 2.438,1.927 2.188,1.927 2.188,1.927 1.802,1.094 true 0.104,0.094 0.417,0.25 0.313,0.156 10 *a 2.646,1.531 3.208,1.865 0.563,0.333 10 CANP 0.417,1.031 0.979,1.365 0.563,0.333 10 G79 2.479,1.844 3.115,2.115 0.635,0.271 10 CANN
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-9 (CANP) - G79-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 5 CAN JUNCTION CONNECTOR)

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)
a.
C266890C06
2.406,1.094 2.813,1.354 0.406,0.26 0.896,0.76 1.104,0.76 1.104,0.76 1.385,1.167 true 0.896,1.635 1.135,1.635 1.135,1.635 1.375,1.302 true 1.083,1.865 1.323,1.865 1.323,1.865 1.448,1.292 true 0.969,0.5 1.177,0.5 1.177,0.5 1.458,1.188 true 1.875,1.885 1.656,1.885 1.656,1.885 1.521,1.292 true 1.917,0.427 1.75,0.427 1.75,0.427 1.542,1.188 true 0.063,0.052 0.375,0.208 0.313,0.156 10 *a 2.479,1.146 2.792,1.302 0.313,0.156 10 N32 0.344,0.688 0.885,0.875 0.542,0.188 10 CANH*d 0.365,1.552 0.917,1.75 0.552,0.198 10 CANL*d 0.552,1.781 1.104,1.979 0.552,0.198 10 CANL*c 0.406,0.406 0.948,0.594 0.542,0.188 10 CANH*c 1.906,1.813 2.458,2.01 0.552,0.198 10 CANL*b 1.958,0.333 2.5,0.521 0.542,0.188 10 CANH*b
*a Rear view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
*c to No. 6 CAN Junction Connector
*d to No. 4 CAN Junction Connector (for Power Seat) or Main Body ECU (Multiplex Network Body ECU) (except Power Seat)


Disconnect the No. 5 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N32-8 (CANH) - N32-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N32-9 (CANH) - N32-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N32-10 (CANH) - N32-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to multiplex network door ECU CAN branch wire) B
NG (to No. 6 CAN junction connector CAN main wire) C
NG (to No. 4 CAN junction connector CAN main wire) (for Power Seat) D
NG (to main body ECU [multiplex network body ECU] CAN main wire) (except Power Seat) E



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

13.CONNECT CONNECTOR

C

15.CONNECT CONNECTOR

D

17.CONNECT CONNECTOR

E

23.CONNECT CONNECTOR
13.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX NETWORK DOOR ECU)
14.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX NETWORK DOOR ECU)
a.
C251435C05
0.313,1.042 0.76,1.302 0.448,0.26 2.708,1.688 2.406,1.688 2.406,1.688 2.229,1.188 true 2.719,1.385 2.49,1.385 2.49,1.385 2.313,1.188 true 2.771,1.302 3.188,1.469 0.417,0.167 10 CANP 2.75,1.604 3.167,1.771 0.417,0.167 10 CANN 0.406,1.094 0.719,1.292 0.313,0.198 10 U18 0.135,0.115 0.552,0.281 0.417,0.167 10 *a
*a Rear view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U18-13 (CANP) - U18-14 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX NETWORK DOOR ECU (CANP, CANN)

15.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 CAN JUNCTION CONNECTOR)
16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 CAN JUNCTION CONNECTOR)
a.
C210060C18
0.323,0.917 0.802,1.167 0.479,0.25 0.948,0.49 1.115,0.49 1.115,0.49 1.344,0.865 true 2.24,0.344 2.063,0.344 2.063,0.344 1.729,0.854 true 0.51,0.417 0.948,0.594 0.438,0.177 10 CANH 0.427,0.958 0.844,1.188 0.417,0.229 10 N31 0.063,0.063 0.271,0.24 0.208,0.177 10 *a 2.313,0.281 2.75,0.458 0.438,0.177 10 CANL
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)


Disconnect the No. 6 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-3 (CANH) - N31-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

17.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR)
18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR)
a.
C277472C04
1.438,0.135 1.854,0.385 0.417,0.25 1.292,1.125 0.917,0.75 0.917,0.75 0.667,0.75 true 1.26,1.448 1.01,1.74 1.01,1.74 0.677,1.74 true 1.448,1.146 1.25,0.417 1.25,0.417 1,0.417 true 1.448,1.417 1.281,2 1.281,2 1.115,2 true 2.229,1.917 2,1.917 2,1.917 1.625,1.458 true 2.25,0.458 2.021,0.458 2.021,0.458 1.635,1.135 true 0.104,0.083 0.417,0.24 0.313,0.156 10 *a 1.521,0.177 1.917,0.417 0.396,0.24 10 N30 0.125,0.677 0.75,0.896 0.625,0.219 10 CANH*b 0.167,1.667 0.813,1.917 0.646,0.25 10 CANL*b 0.542,1.917 1.188,2.167 0.646,0.25 10 CANL*c 0.458,0.333 1.083,0.552 0.625,0.219 10 CANH*c 2.281,1.813 2.927,2.063 0.646,0.25 10 CANL*d 2.292,0.344 2.917,0.563 0.625,0.219 10 CANH*d
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to No. 5 CAN Junction Connector
*d to Position Control ECU and Switch Assembly (w/ Seat Memory)


Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-1 (CANH) - N30-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N30-2 (CANH) - N30-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N30-3 (CANH) - N30-9 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to main body ECU [multiplex network body ECU] CAN main wire) B
NG (to position control ECU and switch assembly CAN branch wire) (w/ Seat Memory) C
NG (to No. 5 CAN junction connector CAN main wire) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

19.CONNECT CONNECTOR

C

21.CONNECT CONNECTOR

D

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

19.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
20.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
C277474C01
0.292,0.969 0.833,1.26 0.542,0.292 2.604,1.604 2.354,1.604 2.354,1.604 1.854,1.104 true 2.438,1.927 2.188,1.927 2.188,1.927 1.802,1.094 true 0.104,0.094 0.417,0.25 0.313,0.156 10 *a 2.646,1.531 3.208,1.865 0.563,0.333 10 CANP 0.417,1.031 0.979,1.365 0.563,0.333 10 G79 2.479,1.844 3.115,2.115 0.635,0.271 10 CANN
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-9 (CANP) - G79-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTED TO MAIN BODY ECU (CANP, CANN)

21.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH ASSEMBLY)
22.CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH ASSEMBLY)
a.
C219233C02
1.302,1.417 1.698,1.688 0.396,0.271 2.594,1.76 2.458,1.76 2.458,1.76 2.302,1.573 true 2.521,1.969 2.385,1.969 2.385,1.969 2.219,1.573 true 0.083,0.063 0.396,0.302 0.313,0.24 10 false *a 1.406,1.438 1.771,1.667 0.365,0.229 10 false e6 2.635,1.646 3.177,1.917 0.542,0.271 10 false CANN 2.573,1.875 3.115,2.146 0.542,0.271 10 false CANP
*a Rear view of wire harness connector
(to Position Control ECU and Switch Assembly)


Disconnect the position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-8 (CANP) - e6-7 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTED TO POSITION CONTROL ECU AND SWITCH ASSEMBLY (CANP, CANN)

23.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 5 CAN junction connector.

C278787C01
6.01,0.781 6.438,1.042 0.427,0.26 2.51,0.844 2.938,1.104 0.427,0.26 4.615,0.396 4.781,0.396 4.781,0.396 5.083,0.76 true 5.927,1.354 5.75,1.354 5.75,1.354 5.583,1.135 true 2.177,1.448 1.979,1.448 1.979,1.448 1.708,1 true 1.094,0.531 1.26,0.531 1.26,0.531 1.563,0.896 true 1.167,0.323 1.375,0.323 1.375,0.323 1.635,0.896 true 2.344,0.25 2.146,0.25 2.146,0.25 1.708,0.906 true 1.229,1.344 1.396,1.344 1.396,1.344 1.552,1.021 true 1.313,1.583 1.479,1.583 1.479,1.583 1.635,1 true 0.104,0.083 0.417,0.24 0.313,0.156 10 *a 2.406,0.167 3.135,0.333 0.729,0.167 10 CANH*c 4.021,0.094 4.333,0.25 0.313,0.156 10 *b 2.219,1.365 2.948,1.531 0.729,0.167 10 CANL*c 0.781,1.5 1.51,1.667 0.729,0.167 10 CANL*d 0.698,1.25 1.427,1.417 0.729,0.167 10 CANL*e 0.563,0.458 1.292,0.625 0.729,0.167 10 CANH*e 0.604,0.229 1.333,0.396 0.729,0.167 10 CANH*d 5.979,1.281 6.708,1.448 0.729,0.167 10 BAT 4.375,0.323 5.104,0.49 0.729,0.167 10 CG 2.604,0.896 3.333,1.063 0.729,0.167 10 N32 6.083,0.833 6.813,1 0.729,0.167 10 G14
*a Rear view of wire harness connector
(to No. 5 CAN Junction Connector)
*b Front view of DLC3
*c to Multiplex Network Door ECU *d to No. 6 CAN Junction Connector
*e to No. 4 CAN Junction Connector (for Power Seat) or Main Body ECU (Multiplex Network Body ECU) (except Power Seat) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to

*1: for Power Seat

*2: except Power Seat

N32-8 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Multiplex network door ECU
N32-19 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
N32-8 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
N32-19 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
N32-9 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short No. 6 CAN junction connector
N32-20 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
N32-9 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
N32-20 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
N32-10 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short
·

No. 4 CAN junction connector*1

·

Main body ECU (multiplex network body ECU)*2


N32-21 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
N32-10 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
N32-21 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short


Result:
Result Proceed to
OK A
NG (to multiplex network door ECU CAN branch wire) B
NG (to No. 6 CAN junction connector CAN main wire) C
NG (to No. 4 CAN junction connector CAN main wire) (for Power Seat) D
NG (to main body ECU [multiplex network body ECU] CAN main wire) (except Power Seat) E




A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

25.CONNECT CONNECTOR

C

27.CONNECT CONNECTOR

D

29.CONNECT CONNECTOR

E

35.CONNECT CONNECTOR
25.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX NETWORK DOOR ECU)
26.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX NETWORK DOOR ECU)
a.
C251432C02
0.281,2.49 0.677,2.719 0.396,0.229 0.375,0.854 0.771,1.083 0.396,0.229 1.042,2.01 1.281,2.01 1.281,2.01 1.656,2.427 true 2.229,2.865 2.51,3.135 2.51,3.135 2.802,3.135 true 2.313,1.104 2.5,1.333 2.5,1.333 2.74,1.333 true 2.25,1.104 2.323,1.604 2.323,1.604 2.563,1.604 true 0.073,0.042 0.385,0.198 0.313,0.156 10 *a 0.125,1.917 0.438,2.073 0.313,0.156 10 *b 0.344,2.531 0.625,2.719 0.281,0.188 10 G14 0.438,0.906 0.719,1.094 0.281,0.188 10 U18 2.583,1.531 3.094,1.698 0.51,0.167 10 CANN 2.771,1.26 3.281,1.427 0.51,0.167 10 CANP 2.833,3.063 3.344,3.229 0.51,0.167 10 BAT 0.802,1.927 1.313,2.094 0.51,0.167 10 CG
*a Rear view of wire harness connector
(to Multiplex Network Door ECU)
*b Front view of DLC3


Disconnect the multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U18-13 (CANP) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
U18-14 (CANN) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
U18-13 (CANP) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
U18-14 (CANN) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX NETWORK DOOR ECU (CANP, CANN)

27.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 CAN JUNCTION CONNECTOR)
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 CAN JUNCTION CONNECTOR)
a.
C251147C04
2.438,0.708 2.854,0.969 0.417,0.26 0.469,2.51 0.885,2.771 0.417,0.26 1.052,1.188 1.198,1.188 1.198,1.188 1.396,0.906 true 1.333,0.313 1.479,0.313 1.479,0.313 1.677,0.729 true 2.438,3.083 2.323,3.083 2.323,3.083 2.198,2.844 true 1.302,2.104 1.479,2.104 1.479,2.104 1.667,2.438 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.094,1.969 0.406,2.125 0.313,0.156 10 false *b 0.948,0.25 1.354,0.396 0.406,0.146 10 false CANL 0.594,1.125 1.042,1.375 0.448,0.25 10 false CANH 2.51,0.771 2.958,1.021 0.448,0.25 10 false N31 0.531,2.563 0.979,2.813 0.448,0.25 10 false G14 1.052,2.031 1.5,2.281 0.448,0.25 10 false CG 2.479,3.01 2.927,3.26 0.448,0.25 10 false BAT
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)
*b Front view of DLC3


Disconnect the No. 6 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-3 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N31-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N31-3 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N31-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

29.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR)
30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 4 CAN junction connector.

C278788C02
2.521,0.833 2.906,1.094 0.385,0.26 6.021,0.844 6.406,1.104 0.385,0.26 5.594,1.125 5.719,1.375 5.719,1.375 5.875,1.375 true 4.802,0.51 4.948,0.51 4.948,0.51 5.083,0.76 true 1.094,0.594 1.24,0.594 1.24,0.594 1.521,0.844 true 1.323,0.24 1.469,0.24 1.469,0.24 1.656,0.844 true 1.135,1.25 1.281,1.25 1.281,1.25 1.521,1.052 true 1.344,1.583 1.469,1.583 1.469,1.583 1.646,1.063 true 1.771,1.052 1.948,1.458 1.948,1.458 2.104,1.458 true 1.76,1.052 1.938,1.458 1.938,1.458 2.094,1.458 true 1.771,0.844 2,0.229 2,0.229 2.156,0.229 true 0.104,0.094 0.417,0.25 0.313,0.156 10 *a 4.021,0.167 4.333,0.323 0.313,0.156 10 *b 0.521,0.5 1.167,0.74 0.646,0.24 10 CANH*c 0.823,1.479 1.49,1.677 0.667,0.198 10 CANL*d 0.604,1.167 1.25,1.406 0.646,0.24 10 CANL*c 0.75,0.135 1.417,0.333 0.667,0.198 10 CANH*d 5.906,1.281 6.573,1.479 0.667,0.198 10 BAT 4.583,0.427 5.25,0.625 0.667,0.198 10 CG 2.583,0.885 3.25,1.083 0.667,0.198 10 N30 6.083,0.885 6.75,1.083 0.667,0.198 10 G14 2.198,0.125 2.865,0.323 0.667,0.198 10 CANH*e 2.146,1.344 2.813,1.542 0.667,0.198 10 CANL*e
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3
*c to Main Body ECU (Multiplex Network Body ECU) *d to No. 5 CAN Junction Connector
*e to Position Control ECU and Switch Assembly (w/ Seat Memory) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to

*: w/ Seat Memory

N30-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Main body ECU (multiplex network body ECU)
N30-7 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
N30-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
N30-7 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
N30-2 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short No. 5 CAN junction connector
N30-8 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
N30-2 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
N30-8 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
N30-3 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short Position control ECU and switch assembly*
N30-9 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
N30-3 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
N30-9 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to main body ECU [multiplex network body ECU] CAN main wire) B
NG (to position control ECU and switch assembly CAN branch wire or connector) (w/ Seat Memory) C
NG (to No. 5 CAN junction connector CAN main wire) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

31.CONNECT CONNECTOR

C

33.CONNECT CONNECTOR

D

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

31.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Result
NEXT



NEXT

32.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
32.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
C277475C01
0.313,2.542 0.708,2.823 0.396,0.281 0.354,0.885 0.75,1.167 0.396,0.281 1.104,2.156 1.313,2.156 1.313,2.156 1.625,2.469 true 2.635,3.156 2.406,3.156 2.406,3.156 2.188,2.896 true 2.49,1.656 2.26,1.656 2.26,1.656 1.833,1.188 true 2.344,1.917 2.115,1.917 2.115,1.917 1.781,1.188 true 0.188,0.167 0.5,0.323 0.313,0.156 10 *a 0.167,1.927 0.479,2.083 0.313,0.156 10 *b 0.365,2.604 0.938,2.958 0.573,0.354 10 G14 0.417,0.948 0.885,1.198 0.469,0.25 10 G79 2.552,1.583 3.188,1.813 0.635,0.229 10 CANP 2.375,1.844 3.01,2.073 0.635,0.229 10 CANN 0.865,2.094 1.5,2.323 0.635,0.229 10 CG 2.698,3.073 3.333,3.302 0.635,0.229 10 BAT
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-9 (CANP) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G79-10 (CANN) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G79-9 (CANP) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G79-10 (CANN) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)

33.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Result
NEXT



NEXT

34.CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH ASSEMBLY)
34.CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH ASSEMBLY)
a.
C251433C05
0.531,0.865 0.948,1.115 0.417,0.25 0.302,2.5 0.719,2.75 0.417,0.25 1.656,2.427 1.5,2.063 1.5,2.063 1.396,2.063 true 2.25,2.865 2.333,3.135 2.333,3.135 2.49,3.135 true 2.042,1.135 2.125,1.406 2.125,1.406 2.281,1.406 true 1.896,1.125 2.063,1.635 2.063,1.635 2.26,1.635 true 0.052,0.063 0.365,0.219 0.313,0.156 10 false *a 0.094,2.031 0.406,2.188 0.313,0.156 10 false *b 0.656,0.906 0.969,1.063 0.313,0.156 10 false e6 0.385,2.552 0.698,2.708 0.313,0.156 10 false G14 1.146,1.979 1.458,2.135 0.313,0.156 10 false CG 2.531,3.073 2.99,3.302 0.458,0.229 10 false BAT 2.302,1.531 2.865,1.76 0.563,0.229 10 false CANP 2.323,1.313 2.885,1.542 0.563,0.229 10 false CANN
*a Rear view of wire harness connector
(to Position Control ECU and Switch Assembly)
*b Front view of DLC3


Disconnect the position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-8 (CANP) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
e6-7 (CANN) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
e6-8 (CANP) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
e6-7 (CANN) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTED TO POSITION CONTROL ECU AND SWITCH ASSEMBLY (CANP, CANN)

35.CONNECT CONNECTOR
a.

Reconnect the No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

32.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)