Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) J

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the EFI-MAIN NO. 1 relay, closing the contacts and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A299783
5.604,0.354 5.771,0.521 0.167,0.167 10 false 9 5.833,0.448 6.25,0.615 0.417,0.167 10 false IG2D 5.417,0.917 7,1.25 1.583,0.333 10 false Certification ECU (Smart Key ECU Assembly)*2 5.833,1.875 6.25,2.042 0.417,0.167 10 false IGSW 5.833,2.375 6.167,2.542 0.333,0.167 10 false +B2 5.833,2.844 6.083,3.01 0.25,0.167 10 false +B 5.833,3.729 6.333,3.896 0.5,0.167 10 false MREL 5.833,4.26 6.083,4.427 0.25,0.167 10 false E1 6.167,4.667 6.583,4.833 0.417,0.167 10 false ECM 5.49,2.375 5.823,2.542 0.333,0.167 10 false A62 5.5,1.979 5.833,2.146 0.333,0.167 10 false A62 5.531,1.792 5.781,1.958 0.25,0.167 10 false 37 5.573,2.188 5.74,2.354 0.167,0.167 10 false 3 5.573,2.656 5.74,2.823 0.167,0.167 10 false 2 5.531,3.542 5.781,3.708 0.25,0.167 10 false 46 5.531,4.073 5.781,4.24 0.25,0.167 10 false 16 2.094,4.052 3.177,4.219 1.083,0.167 10 false EFI-MAIN NO. 1 2.948,3.625 3.115,3.792 0.167,0.167 10 false 1 2.948,3.198 3.115,3.365 0.167,0.167 10 false 3 2.167,3.198 2.333,3.365 0.167,0.167 10 false 5 2.167,3.625 2.333,3.792 0.167,0.167 10 false 2 2.49,2.667 2.823,2.833 0.333,0.167 10 false IG2 2.167,2.146 2.333,2.313 0.167,0.167 10 false 2 2.948,2.135 3.115,2.302 0.167,0.167 10 false 1 2.948,1.875 3.115,2.042 0.167,0.167 10 false 5 2.167,1.875 2.333,2.042 0.167,0.167 10 false 3 0.865,2.125 1.198,2.292 0.333,0.167 10 false IG2 0.5,3.458 1.583,3.625 1.083,0.167 10 false EFI-MAIN NO. 1 0.542,4.448 1.042,4.698 0.5,0.25 10 false Battery 0.375,1.198 0.708,1.365 0.333,0.167 10 false AM2 1,0.833 1.25,1 0.25,0.167 10 false G4 1,1 2.75,1.25 1.75,0.25 10 false Ignition Switch Assembly*1 1.208,0.563 1.625,0.729 0.417,0.167 10 false AM2 2.01,0.563 2.344,0.729 0.333,0.167 10 false IG2 2.333,0.354 2.5,0.521 0.167,0.167 10 false 3 1.031,0.354 1.198,0.521 0.167,0.167 10 false 4 4.146,2.135 4.479,2.302 0.333,0.167 10 false IGN 5.417,0.75 5.75,0.917 0.333,0.167 10 false G82 5.49,2.844 5.823,3.01 0.333,0.167 10 false A62 5.49,3.729 5.823,3.896 0.333,0.167 10 false A62 5.5,4.26 5.833,4.427 0.333,0.167 10 false B77 2.323,4.667 4.333,4.865 2.01,0.198 10 false *1: w/o Entry and Start System 2.323,5 4.25,5.198 1.927,0.198 10 false *2: w/ Entry and Start System 0.396,3.896 0.979,4.063 0.583,0.167 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 RELAY VOLTAGE)
a.
A298898C03
0.073,0.073 0.385,0.229 0.313,0.156 10 *1 2.031,0.75 2.344,0.906 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 IG2 Relay


Remove the IG2 relay from the engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IG2 relay terminal 1 - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/o Entry and Start System) B
NG (w/ Entry and Start System) C



A

2.CHECK HARNESS AND CONNECTOR (BATTERY - IG2 RELAY, EFI-MAIN NO. 1 RELAY)

B

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

C

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - IG2 RELAY)
2.CHECK HARNESS AND CONNECTOR (BATTERY - IG2 RELAY, EFI-MAIN NO. 1 RELAY)
a.
A298898C03
0.073,0.073 0.385,0.229 0.313,0.156 10 *1 2.031,0.75 2.344,0.906 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 IG2 Relay


Remove the IG2 relay from the engine room relay block and junction block assembly.


b.
A296485C01
0.083,0.073 0.396,0.229 0.313,0.156 10 *1 2.063,3.635 2.375,3.792 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 1 Relay


Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
IG2 relay terminal 3 - Body ground Always 11 to 14 V
EFI-MAIN NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT IG2 RELAY, EFI-MAIN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT IG2 RELAY, EFI-MAIN NO. 1 RELAY

b.

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG2 RELAY, EFI-MAIN NO. 1 RELAY - BODY GROUND)

NG

REPLACE IG2 RELAY OR EFI-MAIN NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (IG2 RELAY, EFI-MAIN NO. 1 RELAY - BODY GROUND)
a.

Remove the IG2 relay from the engine room relay block and junction block assembly.


b.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 relay terminal 2 - Body ground Always Below 1 Ω
EFI-MAIN NO. 1 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY, EFI-MAIN NO. 1 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY, EFI-MAIN NO. 1 RELAY - ECM)
a.

Remove the IG2 relay from the engine room relay block and junction block assembly.


b.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 relay terminal 5 - A62-37 (IGSW) Always Below 1 Ω
EFI-MAIN NO. 1 relay terminal 3 - A62-2 (+B) Always Below 1 Ω
EFI-MAIN NO. 1 relay terminal 3 - A62-3 (+B2) Always Below 1 Ω
EFI-MAIN NO. 1 relay terminal 1 - A62-46 (MREL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-16 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G4-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - IG2 RELAY)
a.

Remove the IG2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-9 (IG2D) - IG2 relay terminal 1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR