Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0111  Intake Air Temperature Sensor Gradient Too High  


DESCRIPTION

A293042E01
3.323,2.188 3.74,1.771 false 2,0.51 3.073,0.708 1.073,0.198 10 Resistance 1.604,0.229 2.677,0.427 1.073,0.198 10 Fig. 1: 2.115,0.792 3.188,0.99 1.073,0.198 10 [kΩ] 2.208,0.99 2.531,1.188 0.323,0.198 10 30 2.208,1.156 3.281,1.354 1.073,0.198 10 20 2.208,1.438 3.281,1.635 1.073,0.198 10 10 2.281,1.719 3.354,1.917 1.073,0.198 10 5 2.281,1.938 3.354,2.135 1.073,0.198 10 3 2.281,2.104 3.354,2.302 1.073,0.198 10 2 2.271,2.365 3.344,2.563 1.073,0.198 10 1 2.167,2.677 2.667,2.917 0.5,0.24 10 0.5 2.167,2.865 3.24,3.063 1.073,0.198 10 0.3 2.156,3.042 3.229,3.24 1.073,0.198 10 0.2 2.156,3.313 3.229,3.51 1.073,0.198 10 0.1 2.458,3.708 3.531,3.906 1.073,0.198 10 -20 2.833,3.708 3.906,3.906 1.073,0.198 10 0 3.104,3.708 4.177,3.906 1.073,0.198 10 20 3.427,3.708 4.5,3.906 1.073,0.198 10 40 3.729,3.708 4.802,3.906 1.073,0.198 10 60 4.052,3.708 5.125,3.906 1.073,0.198 10 80 4.313,3.708 5.385,3.906 1.073,0.198 10 100 4.802,3.708 5.875,3.906 1.073,0.198 10 [°C] 2.5,3.958 3.573,4.156 1.073,0.198 10 -4 2.802,3.958 3.875,4.156 1.073,0.198 10 32 3.115,3.958 4.188,4.156 1.073,0.198 10 68 3.396,3.958 3.76,4.281 0.365,0.323 10 104 3.698,3.958 4.094,4.292 0.396,0.333 10 140 4.021,3.958 4.417,4.292 0.396,0.333 10 176 4.333,3.958 4.729,4.292 0.396,0.333 10 212 4.781,3.969 5.854,4.167 1.073,0.198 10 [°F] 2.854,4.281 3.927,4.479 1.073,0.198 10 Temperature 3.771,1.625 4.844,1.823 1.073,0.198 10 Acceptable

The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0111 Intake Air Temperature Sensor Gradient Too High Either of the following conditions is met (2 trip detection logic).
·

The intake air temperature change from the previous trip warm up to the following trip is small.

·

The change in the intake air temperature after engine start is less than the threshold value.


Mass air flow meter sub-assembly Comes on DTC stored

MONITOR DESCRIPTION

The ECM performs OBD II monitoring based on the values from the intake air temperature sensor. If there is no change of the sensor value within the normal range, the ECM will not be able to perform OBD II monitoring or will misdiagnose that there is a malfunction in the sensor. The ECM detects when the intake air temperature sensor value is stuck by performing monitoring after the ignition switch is turned off or the engine is started (short soak or long soak).

MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A198822E32
2.229,2.917 2.906,3.302 0.677,0.385 10 Warming Up 2.896,2.927 4.063,3.115 1.167,0.188 10 5 minutes or more 2.021,2.094 2.333,2.365 0.313,0.271 10 [A] 2.51,1.792 2.875,2.063 0.365,0.271 10 [B] 3.354,1.771 3.635,2.083 0.281,0.313 10 [C] 3.99,3.125 4.229,3.292 0.24,0.167 10 [D] 1.135,1.094 1.677,1.313 0.542,0.219 10 40 km/h 1.302,1.927 1.771,2.198 0.469,0.271 10 Idling 0.5,2.208 1.74,2.417 1.24,0.208 10 Ignition Switch ON 4.167,0.177 5.927,0.375 1.76,0.198 10 Total of 5 minutes or more 4.833,0.698 5.125,1.01 0.292,0.313 10 [E] 6.156,3.385 6.354,3.563 0.198,0.177 10 [F]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

HINT:

During steps [A] through [C], if the change in the intake air temperature is below 1°C (1.8°F), the intake air temperature sensor (mass air flow meter sub-assembly) is malfunctioning. It is not necessary to continue this procedure.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0111.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].



13.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result again [F].

HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F] again.



CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0111 and other DTCs are output A
DTC P0111 is output B


HINT:
·

If any DTCs other than P0111 are output, troubleshoot those DTCs first.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





A

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY