When the position control ECU and switch assembly does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2651 | Reclining Sensor Malfunction | The forward and backward lock detection position of the sensor is the same. | ·
Position control ECU and switch assembly ·
Reclining motor (Separate type front seatback spring assembly) ·
Harness or connector |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Reclining |
Motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Reclining Motor [Separate Type Front Seatback Spring Assembly]) |
Disconnect the f1 reclining motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| f1-2 - f1-3 | Reclining switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Reclining Motor [Separate Type Front Seatback Spring Assembly]) |
Reconnect the f1 reclining motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| f1-2 - Body ground | Reclining switch on | 4.5 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e6 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e6-11 (SSRR) - f1-2 | Always | Below 1 Ω |
| e6-1 (SGND) - f1-3 | Always | Below 1 Ω |
| e6-11 (SSRR) - Body ground | Always | 10 kΩ or higher |
| e6-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the separate type front seatback spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY
Inspect the separate type front seatback spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e18 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e18-9 (RCL+) - f1-4 | Always | Below 1 Ω |
| e18-11 (RCL-) - f1-1 | Always | Below 1 Ω |
| e18-9 (RCL+) - Body ground | Always | 10 kΩ or higher |
| e18-11 (RCL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG